10G SPF+ ports are not working on my Supermicro E300-9A

grim-reaper

@stephenw10 Thanks for all the help, I will get fiber modules for both the spf+ ports. Do you know if this will work with pfsense https://store-ui.in/collections/unifi-accessories/products/10-gbps-multi-mode-optical-module

stephenw10

No, sorry, I've never tested that. I would expect it to though if the NIC accepts it.

grim-reaper

@stephenw10 Ohh no worries, I will try and talk to supermicro folks and update this thread on what I ended up doing.

grim-reaper

@stephenw10 so I got SPF+ fiber modules from super micro and they work fine within ubiquiti to ubiquiti connection with LC type cable.

But when I connect my supermicro SFP+ to my ubiquiti USW it doesn't

Here are the output of same commands:

ix3: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 39.91 C Voltage: 3.37 Volts
	RX: 0.41 mW (-3.83 dBm) TX: 0.69 mW (-1.56 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

I don't know what I am doing wrong, supermicro support said these modules are compatible with E300-9A.

stephenw10

The switch ports are at 10G?

Do you see link if you connect two ix ports on the SM?

You tried ifconfig down/up on the interface?

grim-reaper

@stephenw10 I will try it today. And also I just wanted to mention that all the interfaces except two WAN interfaces are in bridge mode.

grim-reaper

@stephenw10

Using SFP+ DAC modules while ix2 and ix3 not part of BRIDGE interfaces

Output of ifconfig -vvvm [ix2, ix3] :

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect (10Gbase-Twinax <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect (10Gbase-Twinax <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Screenshot from 2023-01-13 19-53-36.png

Connection from pfsense to USW-Agg via 10G DAC without being a part of BRIDGE

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Using SFP+ fiber modules while ix2 and ix3 not part of BRIDGE interfaces

Output of `ifconfig -vvvm [ix3, ix2]`

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect (10Gbase-SR <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0257 DATE: 2022-11-30
	module temperature: 35.81 C Voltage: 3.34 Volts
	RX: 0.60 mW (-2.17 dBm) TX: 0.63 mW (-1.94 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 37 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1D
	00 00 11 98 5C 37 04 BB 03 86 91 6F C4 46 7D 3C
	44 D5 BA 00 00 00 00 00 00 00 00 00 1D C2 8C 47

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect (10Gbase-SR <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 41.13 C Voltage: 3.37 Volts
	RX: 0.56 mW (-2.47 dBm) TX: 0.69 mW (-1.56 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

Screenshot from 2023-01-13 20-08-53.png

Connection from pfsense to USW-Agg using SPF+ fiber modules without being a part of BRIDGE:

Output of ifconfig -vvvm [ix3, ix2] :

I tried ifconfig ix3/ix2 up/down but that doesn't seem to have any effect...

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0257 DATE: 2022-11-30
	module temperature: 41.54 C Voltage: 3.34 Volts
	RX: 0.49 mW (-3.04 dBm) TX: 0.64 mW (-1.87 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 37 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1D
	00 00 11 98 5C 37 04 BB 03 86 91 6F C4 46 7D 3C
	44 D5 BA 00 00 00 00 00 00 00 00 00 1D C2 8C 47

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 44.41 C Voltage: 3.37 Volts
	RX: 0.00 mW (-40.00 dBm) TX: 0.70 mW (-1.49 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

Screenshot from 2023-01-13 20-16-06.png

stephenw10

Hmm, so none of those tests include ix2/3 as part of a bridge?

grim-reaper

@stephenw10 yeah... I am so confused...

stephenw10

Hmm, so you give two sets of output above where the link is up correctly. Can you not use either of those setups?
I'm not sure what the difference is in the last output that fails...

grim-reaper

@stephenw10 I am not sure either. But I want the interfaces to be a part of the BRIDGE group. And connecting from SM to USW-Agg never works, it always auto negotiates to 1G instead of 10G

stephenw10

Hmm, so when the ports are part of a bridge they link to the switch but only at 1G? Presumably as shown above with pfSense showing 'Unknown' and the switch showing 1G?

But when removed from the bridge they are able to link at 10G?

You're running 2.6 here? You might try a 2.7 snapshot as a test. The behaviour of bridges inherited port settings changed there recently.

Steve

grim-reaper

@stephenw10 said in 10G SPF+ ports are not working on my Supermicro E300-9A:

Hmm, so when the ports are part of a bridge they link to the switch but only at 1G? Presumably as shown above with pfSense showing 'Unknown' and the switch showing 1G?

No, the connection to the switch never work no matter if the ports in SM are part of BRIDGE or not. At most they auto-negotiate to 1G with both DAC and Fiber module.

@stephenw10 said in 10G SPF+ ports are not working on my Supermicro E300-9A:

But when removed from the bridge they are able to link at 10G?

The link between SM work when removed from BRIDGE with both fiber and DAC cable.

So I still give 2.7 a try?

grim-reaper

@stephenw10

@stephenw10 said in 10G SPF+ ports are not working on my Supermicro E300-9A:

You're running 2.6 here?

I'm running pfsense+ and the version is 22.05.

stephenw10

Then try 23.01. If you're running ZFS you can roll back the BE snap to 22.05 if required.

grim-reaper

@stephenw10 Tried the 23.01 build but same issue no luck there either. Tested all similar cases with it but none worked.

stephenw10

So unable to get a link to the switch at all or only able to link 1G?

You haven't seen a 10G link to the switch at any time?

grim-reaper

@stephenw10 Unfortunately no ... I tried all cables and all other suggestions mentioned in this thread.

stephenw10

Hmm. What options does the switch give you for link speeds on the port?

grim-reaper

@stephenw10 These are the options I see on all 10G ports on both my Ubiquiti SWs

Screenshot 2023-01-17 at 11.19.42 PM.png

10G SPF+ ports are not working on my Supermicro E300-9A

Using SFP+ DAC modules while ix2 and ix3 not part of BRIDGE interfaces

Connection from pfsense to USW-Agg via 10G DAC without being a part of BRIDGE

Using SFP+ fiber modules while ix2 and ix3 not part of BRIDGE interfaces

Output of ifconfig -vvvm [ix3, ix2]

Connection from pfsense to USW-Agg using SPF+ fiber modules without being a part of BRIDGE:

Output of `ifconfig -vvvm [ix3, ix2]`