1100 upgrade, 22.05->23.01, high mem usage
-
@beerguzzle said in 1100 upgrade, 22.05->23.01, high mem usage:
My mem usage jumped up at precisely 3 AM this morning, when the cron job scripts in /etc/periodic/daily fired off. Something in these scripts caused "unbound" to return to its 179M of resident memory again. To answer questions, yes I do use DNSBL in pfblockerng, with DNSBL groups Easylist and ADs_basic. For DNS over HTTPS, I block Firefox and Google in that list. I also pull in the ASNs for Facebook, to block them in/out all ports.
Here is my mem graph at the moment. The first dip was the upgrade, the second was my reboot at noon yesterday. The big jump was the 3 AM cron job. At this point, I'm going to leave it alone and keep an eye on the memory over the coming days (and hope it doesn't croak).
Same here. Thought my 6100 was stabilized, it hasn’t left 35% since I woke up this morning…. Over double than 22.05.
-
Same here on my 1100. I had to do a fresh install after the upgrade locked it up. I have a very basic config with ZFS and a few openVPN tunnels. After a reboot the memory starts out around 29% and in the course of a day is running at 85%
This sort of problem makes me think twice about spending the extra money to buy netgate hardware.
Roy...
-
Mine is a 2100 and I've noticed that something around 3 am is causing a change (and not giving it back) until I reboot.
Everything left of the red line is 22.05 every right after the update to 23.01
once it changes it stays at the new level even if passing through a second 3am. It does NOT add "more" to the memory footprint on passing a second 3am. just stays right about there.
Not too worried about it in my case because the changes are pretty static. But yes it appear that a 3am there is something causing a spike that doesn't really give it back, or take more next time.
-
@jrey said in 1100 upgrade, 22.05->23.01, high mem usage:
Mine is a 2100 and I've noticed that something around 3 am is causing a change (and not giving it back) until I reboot.
Everything left of the red line is 22.05 every right after the update to 23.01
once it changes it stays at the new level even if passing through a second 3am. It does NOT add "more" to the memory footprint on passing a second 3am. just stays right about there.
Not too worried about it in my case because the changes are pretty static. But yes it appear that a 3am there is something causing a spike that doesn't really give it back, or take more next time.
My 6100 is doing the exact same thing around 3AM and not giving it back. This is the last 2 days:
-
-
-
@rpsmith said in 1100 upgrade, 22.05->23.01, high mem usage:
This sort of problem makes me think twice about spending the extra money to buy netgate hardware.
Roy...
To be fair, what you are seeing is not related to netgate appliances, but something in 23.01 (software) that does not release memory as intended. It does look like it does not claim even more memory at next run (so there is reuse going on at 3:00am).
But this needs to fixed in software, not hardware.
-
This graph is from a SG-3100, which uses UFS and not ZFS.
I only installed Acme package in it. -
Not convinced it is Acme, on my system that is schedule for 3:16 the change happens at 3:00 through 3:10
couple of items I see starting at exactly 3:00 are
the section Rotate log files every hour, if necessary.
the entry "newsyslog"the Section perform daily/weekly/monthly maintenance.
the entry for "periodic daily"and under the section
pfSense specific crontab entries
Created: February 19, 2023, 8:06 pm
the entry for "/etc/rc.periodic daily"Everything else at the 3 hour either has multiple minutes (like 1,31) or a specific mday.
So think here is one of those two maintenance routines, rotation of the logs should be fairly boring.
I might move one of the periodic daily to say hour 2 (nothing else specifically scheduled there on my system) and see if the memory change then aligns to the one or the other.i want to check first and see if the two have to run at the same time for some reason, because the "weekly" and "monthly" run at paired times as well.
-
@jrey So, its not acme, its not ZFS (because UFS system is also affected), its not pfblockerng/snort/suricata since I don't have those installed and I'm facing the same problem around the same time as you guys.
I'm not sure if this is related to logs since I'm not writing anything to the disk (remote syslog):
-
After leaving things alone for a couple of days, the mem usage jumps to about 63% at 3 AM and slowly drops over the next 24 hours to about 53%, then jumps back to 63%. So it is "stable" between these two numbers. I have had no ill effects of this new memory usage since going to 23.01.
Thinking that "unbound" might be holding more DNS cache info than it needs, and that it might be a DNS cache timeout issue, I looked around there in Services->DNS Resolver->Advanced. My "TTL for host cache entries" is 15 minutes, and the "Max TTL for RRsets" is one day. Hmmm. I wonder if I reduced the Max TTL if anything good or bad would happen. I nervous about futzing with anything here.
-
Only difference I have in those settings is the local logging is unchecked for me. Even though I also send to a syslog
Log rotation is generally such a trivial task, I can't see it running for the 10 minutes (in my case)
to me the periodic daily are more likely the cause of the slow, one time over the 10 minutes memory burn.
Now, if left alone at this point it won't change anymore. It will just stay at these new levels. (pretty flat line 1-2% bumps up/down here and there, but nothing near the level of the first 3am after a restart)
based on the before/after upgrade graph or even after a reboot
a) the system isn't very memory stressed (I only have about 45-50 devices behind it)
b) this has only started since the upgrade and is consistent at only happening the first 3am cycle after a restartRed line left of is 22.05 to the right is 23.01
pretty obvious when this was introduced. -
I would think if this were DNS related, memory would fluctuate more often and be less flatline, as has been shown at least in my case where the change is only at first 3am after a reboot.
For the record I don't run DHCP on this NG, that is handled by one of the internal systems for all devices on the network. All devices on LAN point to it for DNS (primarily for pfBlockerNG) but the NG forwards all missing requests to 2 (AD paired DNS systems, both of which have the ability to reach "outside" if they don't have the answer. But neither of the 2 DNS servers accept queries coming in.I'm supporting about 45-50 systems behind the 2100. and typically the memory is 10-15% until at 3am it jumps to 37%-%40 typically after the restart yesterday it was at 12% this morning 39% and it will stay right about there until the next restart.
Not concerned, just more of an observation.
JR -
FYI, there's now package updates available for pfBlockerNG and Suricata. Perhaps this will help.
-
@beerguzzle I posted in similar thread https://forum.netgate.com/topic/177886/23-1-using-more-ram/41. Based on my second day it should not increase again, it's just the first day after reboot from what I see.
-
Unlikely, pfBlockerNG does nothing at 3am and I don't run Suricata. As others have also noted.
-
@jrey I totally agree, but this would also not be the first time that pfBlocker had a memory leak after an update and that package was definitely updated during the upgrade to 23.01. I'll know for sure tomorrow morning!
-
I just applied the pfblockerng update, going from 3.2.0.1 to 3.2.0.2. I did not reboot. The wired mem usage jumped from 55% to 63%.
-
question will be, after the new version settles in, does that new memory come down?
is it's not 3am where you are is it?
The specific (and only) increase I have ever seen, is always and only at 3am, like clockwork.
At that time it jumps up a good 20% and then stays there until the next system restart. Regardless of other activity on the system. Look at the graph I posted memory is a pretty flat line. If the memory usage were a heart rhythm I'd be worried it is so flat.Granted I also see some posts where others have memory usage with really wild fluctuations, they are usually running a lot more stuff on the box than I.
In my case I don't think it has anything to do with Acme, or pfBlockerNG for the reasons and timing of the events i've previously reported.
-
@keyser -- the main reason I went with netgate hardware was this firewall was going to be located 750 miles and 3 states away from me and I was led to believe netgate would be testing all new releases on their different hardware platforms prior to releasing new versions.
That clearly doesn't appear to be the case as my SG-1100 is a "Plain Jane" as you could possibly find and there is a major flaw in 23.01 on their hardware!
Roy...
-
So here you go. in my case the issue is 100% cause by "periodic daily" that runs at 3:00am
left of the red line is where it was after last night's spike, and represents the point at which I restarted the system now.
Green line mark is showing the re-establishing of what I would consider the "normal base line" after a reboot and before the next 3:00am cycle
Blue line is me "pretending" it is currently 3:00am and running "period daily" from an ssh session...there goes the memory.
periodic daily is the default "periodic" provided by freebsd (I don't see any comments with to say that pfsense has modified it)
the other /etc/rc.periodic that also normally runs at 3:00 seems to be the pfsense specific stuff. I didn't even run it in this tests be well the memory is already consumed !Sorry I may have captured and marked up the first screen capture too soon to show the flat line after periodic daily completed
-
@jrey Same here on my 6100. That's the only cron job that kicks off at 3AM besides the hourly pfBlocker updates.