AP with onboard built in NAS abilities/multiple MAC Hardware Layer 2 addresses

[johnpoz]

@JonathanLee if your talking about someone creating a rouge AP (evil twin) and using something like wifi-pumpkin to have users connect to their AP vs the actual AP..

Your AP
MySSID, psk P@55W0rd!

And someone fires up another AP with the same SSID and psk - there is nothing pfsense could do to prevent a client from connecting to that AP..

If you want to lock down a client to only connect to a specific BSSID, keep in mind someone setting up a evil twin AP would more then likely use the same BSSID (mac) as the official one..

How do you think pfsense could have anything to do with such traffic?

edit: your scenario of connecting to the wrong wifi, I had a friend that couldn't figure out why she couldn't print.. Well she was using default SSID "linksys" and was connecting to her neighbors wifi, not hers - heheh So no she couldn't print to the printer on her network ;)

[JKnott]

@JonathanLee

I think you may be creating your own issues. Why are you so worried about ARP etc. If pfSense or any other device wants to access the AP for configuration, etc., it will do an ARP request and then get the MAC at that time. You can also configure the DHCP server to provide static mappings for the AP or any other device. This is what I do here. Any device I own, other than my main desktop computer and my pfSense box get their addresses that way.
Where would this loop come from? Having a different L2 address for a L3 address wouldn't cause a loop. The old address would be replaced in the ARP cache by the new. Broadcast storms are typically caused by a L2 loop.
As for the ARP cache, anything in it expires after a fairly short time, requiring a new ARP request.

[JKnott]

@JonathanLee said in AP unit has multiple MAC Hardware Layer 2 addresses:

when I do an ARP -a it shows it mapped on the devices as the RJ-45 of the AP. I thought it would be on device side the Wi-FI MAC not the RJ-45 again, it's bridged right? Hence, why I think it could have broadcast storms looking for the WiFi or 2.4 or 5ghz MAC.

You're way overthinking this. ARP -a will only show the devices that have connected recently, that is until the cache entry expires. If you don't see something in the cache, then ping it, it will now be in the cache. Again, if you have broadcast storms, it's likely because you created a loop when connecting the various devices. BTW, please say Ethernet or wired connection, rather than "RJ-45", so that you think the way everyone else does. You will never see BSSIDs in pfSense. That's a WiFi only thing.

[JonathanLee]

@JKnott I thought maybe it could someway see the BSSID and the MAC as they are tied together. It could see it if I used I used a wifi card directly installed on the firewall itself I know that. I also found this on Netgate docs.

Per Netgate docs for wifi card:

"Due to the way wireless works in BSS mode (Basic Service Set, client mode) and IBSS mode (Independent Basic Service Set, Ad-Hoc mode), and the way bridging works, a wireless interface cannot be bridged in BSS or IBSS mode. Every device connected to a wireless card in BSS or IBSS mode must present the same MAC address. With bridging, the MAC address passed is the actual MAC of the connected device. This is normally a desirable facet of how bridging works. With wireless, the only way this can function is if all the devices behind that wireless card present the same MAC address on the wireless network."

https://docs.netgate.com/pfsense/en/latest/wireless/bridges.html

Scenario one: Device MAC passed to wireless AP MAC passed to AP Ethernet MAC to PfSense to manage with static mappings.

Scenario two: Device arps out for the AP connected NAS Arp request goes to the AP and AP responses to the device directly again this AP it's in bridge mode so does the AP send the Arp requests up to PfSense still? If so, PfSense says that does not match for my MAC in my static IP mapping for the AP for the NAS I have the Ethernet mapped what does PfSense do with that ARP request?

Scenario three: PfSense is set to dynamically assignment on DHCP. There is no static mappings they are dynamic.

Good research ️

Again, they must present the same MAC on the wireless network, so in theory when in
bridge mode it should pass the actual Mac of the connected devices. Again my AP has a huge HDD that is used for my NAS for example and that is what I think use to cause the Strom and noise all the time. It's MAC is a different MAC and not the Ethernet MAC on that same device. The AP device doesn't care about it just let's users connect, it's the firewall that cares as the MAC does not match it's the Ethernet MAC for that device assigned to that IP. So when devices send ARPs out to find the NAS it's still statically assigned with a different MAC at that firewall. The firewall is hypotheticaly like "good day Mr ARP request I don't have that AP NAS mapping, hmmm but I have the Ethernet MAC mapped on this list." The AP's NAS is hypotheticaly like, "I am already past the bouncer, and traffic is flowing and IPs dancing already."

Again with my set up the NAS works currently, but lots of unwanted noise.

You can see above the MAC-IP host names got mix matched when I was testing this. Why would they Mis Match the hostnames?It should stay with the Ethernet hostname as that MAC is mapped to that IP and hostname.

We can agree that, bridges do not break up broadcast domains only the routers do that.

To quote another airport extreme AP user that spoke with Apple support help desk on this, "According to the tech (apple support) the AirPort Extreme is "unpredictable" if you attempt to use USB drives when the router(AP) is in bridge mode.."

That is exactly what I have done. The AP is in bridge mode and it's using the USB drive huge HDD drive at the same time.

[JKnott]

@JonathanLee said in AP unit has multiple MAC Hardware Layer 2 addresses:

I thought maybe it could someway see the BSSID and the MAC as they are tied together. It could see it if I used I used a wifi card directly installed on the firewall itself I know that. I also found this on Netgate docs.

You appear to be using an AP and not a WiFi card. This means there's no way pfSense can see the SSID.

[JonathanLee]

@JKnott BSSID is what I am saying. That is the MAC mapping of that WiFi network.

"SSID, BSSID, and ESSID are all descriptions of wireless networks. However, these three terms have slightly different meanings which are described here. An access point is only one of many devices that make up a wireless network and the Basic Service Set Identifier (BSSID) refers to any device in the WLAN.

Basic Service Set Identifiers (BSSID) are 48-bit labels that identify which devices conform to MAC-48 conventions. These identifiers are usually linked with a wireless access points MAC address, like when the identifier is sent in an AP beacon but can not be seen without some type of signal analyzer or radio tool."

That's the MAC tied to my NAS usb drive within the airport extreme itself.

Ref: https://internetspeedtest.world/wiki/bssid

There for the reason for the mixed host name with multiple Mac IP mappings, and why I have configured pfSense this way it's for my airport extreme with NAS running in bridge mode. It just works better for me. Under normal non NAS APs, just one MAC would be needed here. However I need two layer 2 addresses because of the NAS for ARP requests to work for it.

Bridges work on the data link layer. This will send everything to the firewall even the ARP request to find the NAS.

[JKnott]

@JonathanLee said in AP unit has multiple MAC Hardware Layer 2 addresses:

BSSID is what I am saying. That is the MAC mapping of that WiFi network.

Forget about the WiFi side. PfSense can't see it. All it can see is the Ethernet connection, which includes the MAC and IP addresses for that connection only. Beyond that, it can see the devices connected via WiFi. The WiFi frame carries the Ethernet frame as payload and adds it's own headers to it.

You can get books about WiFi, if you want to learn more about it. There are some 802.11 books by Matthew Gast, published by O'Reilly that have far more info than you'll ever want to know.

[stephenw10]

In access point mode it does usually just bridge the interfaces. Potentially I could imagine an AP using it's wifi interface as the DHCP client and hence that MAC. I'm pretty sure OpenWRT would do that if you configured it to do it. But I have have never tried nor have I ever seen that happen.

[JonathanLee]

@JKnott

"According to the tech (apple support) the AirPort Extreme is "unpredictable" if you attempt to use USB drives when the router(AP) is in bridge mode.." The AP has a MAC mapped for it's NAS USB drive right? You state that PfSense can not see it again if it's in bridge mode under this configuration it still sees the same broadcast domains and arp requests to find that NAS correct?

Yes let's agree under normal APs without a NAS built in it wouldn't care and it would only need the one MAC for Ethernet and it passes the traffic normally.

But for a network attached storage plugged in by way of USB into the AP why would it act unpredictable per the AP developer when set to bridge mode? It still works.

It creates a kind of weird condition here that I think would require both MACs to mapped. Again it does spot the other host name here meaning it saw and mapped it for a while before it changed the MAC when it updated the table and left the old hostname.

[stephenw10]

The NAS function should still use the Ethernet MAC IMO. If it randomly uses any MAC from the bridge that sounds like a bug.
The only reason I could imagine it using a wireless interface directly would be if it's running as a wireless NAS. But that's quite an extreme edge case.

Probably the best thing here is don't use a WIFI AP as a NAS.

[stephenw10]

It's still using the Ethernet MAC in that screenshot. But because you have 3 hostnames configured for the same IP address it's probably just showing the last matched.

[JonathanLee]

@stephenw10 yeahhh that was the goal so it could find the MAC-IP map when needed and the Ethernet MAC-IP map. Yeahhh so it's updating when needed again it leaves the hostname when it updated to the other MAC in the Arp table but the point is the wireless AP's NAS is mapped.

[JonathanLee]

@stephenw10 it's essentially a wireless NAS it's part of the AP. It's the airport extreme AP/ apple time machine software.

(AP bridge mode to pfSense Firewall)

(Set to Bridge Mode)

(NAS within the AP itself)

(Accessible NAS within bridge mode set AP)

[JonathanLee]

@stephenw10 I made a Redmine ticket for the hostname mix ups because it should update the hostname or block inputting different ones because logs could be wrong if it doesn't use the right hostnames.

[johnpoz]

@JonathanLee said in AP with onboard built in NAS abilities/multiple MAC Hardware Layer 2 addresses:

I made a Redmine ticket for the hostname mix ups

And what is this redmine number? Seems like lack of understanding of basic concepts if you ask me vs some issue with pfsense.

[stephenw10]

If there's a bug here it's probably that you shouldn't be able to add the same IP address to multiple dhcp static mappings.
But you can't ever prevent all config errors.

[JonathanLee]

@stephenw10 we can try to prevent all the errors

[JonathanLee]

@johnpoz https://redmine.pfsense.org/issues/14516

Opened

[johnpoz]

@JonathanLee

"With Multiple static ARP MAC-IP pairing to the same IP address"

So you don't see the problem with this? Thought you wanted to reduce traffic?

So if I create multiple entries for say 192.168.1.100 for like 3 different mac addresses.. And then I want to send traffic to 192.168.1.100 - so I will put 3 packets on the wire? Sending to all 3 mac addresses?

Like I said lack of understanding of basic concepts is the issue here.

[JonathanLee]

@johnpoz Why does the GUI allow it? Leading to, it does allow it. Therefore, why does it map to the wrong host names? If only one shows as an active DHCP lease at a time wouldn't it only send packets to that device? It also would not recognize active leases with multiple entries it shows them offline. Hypothetical situation, an admin has a list of thousands of static DHCP entries, wouldn't he want some type or control for multiple entries and or a way to log the correct hostname that in use at that particular time if he needed multiple entries? It didn't list the right hostname in my example. The PfSense system software now has experimenatal layer 2 Ethernet filtering rules as of 23.05, shouldn't we start to research this? Spoofed MAC addresses so on?