Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.

    Scheduled Pinned Locked Moved General pfSense Questions
    17 Posts 3 Posters 1.1k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • C
      cinlung @stephenw10
      last edited by cinlung

      @stephenw10 said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

      @cinlung said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

      Can you tell me how to set VLAN ID in the PPPoE settings?

      Setup a VLAN 391 on the WAN interface in pfSense. Then move the PPPoE config from WAN to the new VLAN on WAN. Then remove the VLAN config from the modem.

      PPPoE in general works fine in 2.7, I'm using it here. I've seen some issues with IPv6 but v4 works exactly as it did in 2.6.

      Your PPP log shows there is no response at all from the other end which implies it might be using the wrong interface?
      Check the conf file /var/etc/mpd_xxx.conf. Make sure it#s on WAN and the other details in there are correct.

      Steve

      I have been checking back and forth and I cannot seem to see where in WAN interface is this VLAN setting value. I even went to PPP settings and it was not there too. Am I seeing at the wrong place? Clicking "Advanced and MLPPP" buttons brings me to PPP Config page.

      Here is my WAN Screen:
      97e99a90-5046-40a7-a8d2-f12bec02adda-image.png

      And Here is my ppp settings screen:
      cd75ce58-5bac-41ff-9508-5a5e1b8786f3-image.png

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Your WAN interface is igb0 so you first need to create VLAN 391 on igb0. Then you will see igb0.391 as an interface available to set as the PPP parent.

        C 1 Reply Last reply Reply Quote 1
        • fireodoF
          fireodo @cinlung
          last edited by fireodo

          @cinlung said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

          I have been working with 2.6.0 and it was OK with the same settings on the bridge side. After updating to 2.7.0 and even reflash the 2.7.0 RELEASE, the same error persist.

          Your PPPOE settings in extended should look something like that: pppoe.png

          but the Modem should not set any VLAN.

          Kettop Mi4300YL CPU: i5-4300Y @ 1.60GHz RAM: 8GB Ethernet Ports: 4
          SSD: SanDisk pSSD-S2 16GB (ZFS) WiFi: WLE200NX
          pfsense 2.8.0 CE
          Packages: Apcupsd, Cron, Iftop, Iperf, LCDproc, Nmap, pfBlockerNG, RRD_Summary, Shellcmd, Snort, Speedtest, System_Patches.

          C 1 Reply Last reply Reply Quote 0
          • C
            cinlung @stephenw10
            last edited by cinlung

            @stephenw10 said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

            Your WAN interface is igb0 so you first need to create VLAN 391 on igb0. Then you will see igb0.391 as an interface available to set as the PPP parent.

            I actually was able to mimic other post. Here what I did:

            1. Create VLAN 391 and set the igb0 as my Interface
              f4ca560f-ded6-4429-82e1-ddb2c75aeec4-image.png

            2. Create PPP using VLAN as my interface
              8c37d54d-4250-4c24-bd6f-952c93365ae8-image.png

            3. Then went to Interface Assignment and choopse PPP over VLAN and I got this error:

            Aug 7 22:57:41	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
            Aug 7 22:57:41	ppp	6380	[wan_link0] Link: reconnection attempt 3
            Aug 7 22:57:38	ppp	6380	[wan_link0] Link: reconnection attempt 3 in 3 seconds
            Aug 7 22:57:38	ppp	6380	[wan_link0] LCP: Down event
            Aug 7 22:57:38	ppp	6380	[wan_link0] Link: DOWN event
            Aug 7 22:57:38	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
            Aug 7 22:57:29	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
            Aug 7 22:57:29	ppp	6380	[wan_link0] Link: reconnection attempt 2
            Aug 7 22:57:28	ppp	6380	[wan_link0] Link: reconnection attempt 2 in 1 seconds
            Aug 7 22:57:28	ppp	6380	[wan_link0] LCP: Down event
            Aug 7 22:57:28	ppp	6380	[wan_link0] Link: DOWN event
            Aug 7 22:57:28	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
            Aug 7 22:57:19	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
            Aug 7 22:57:19	ppp	6380	[wan_link0] Link: reconnection attempt 1
            Aug 7 22:57:16	ppp	6380	[wan_link0] Link: reconnection attempt 1 in 3 seconds
            Aug 7 22:57:16	ppp	6380	[wan_link0] LCP: Down event
            Aug 7 22:57:16	ppp	6380	[wan_link0] Link: DOWN event
            Aug 7 22:57:16	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
            Aug 7 22:57:07	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
            Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: LayerStart
            Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: state change Initial --> Starting
            Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: Open event
            Aug 7 22:57:07	ppp	6380	[wan_link0] Link: OPEN event
            Aug 7 22:57:07	ppp	6380	[wan] Bundle: Interface ng0 created
            Aug 7 22:57:07	ppp	6380	web: web is not running
            Aug 7 22:57:07	ppp	6380	process 6380 started, version 5.9
            Aug 7 22:57:07	ppp	6380	Multi-link PPP daemon for FreeBSD
            

            Doing the step above will break DHCP setting when you revert to DHCP by backtracking the steps. I had to create PPPoE again in WAN, go to PPP and attach auto created PPPoE to the igb0 (WAN) save. Then revert to DHCP.
            This 2.7.0 RELEASE is surely buggy. For some reason, after this vlan thing, changing back to DHCP on wan does not attach the WAN interface to the DHCP rules and had to be tricked by the method I mentioned above..

            fireodoF 1 Reply Last reply Reply Quote 0
            • fireodoF
              fireodo @cinlung
              last edited by

              @cinlung

              And in the Modem you disabled the VLAN setting? (maybe a modem cold start after that)

              Kettop Mi4300YL CPU: i5-4300Y @ 1.60GHz RAM: 8GB Ethernet Ports: 4
              SSD: SanDisk pSSD-S2 16GB (ZFS) WiFi: WLE200NX
              pfsense 2.8.0 CE
              Packages: Apcupsd, Cron, Iftop, Iperf, LCDproc, Nmap, pfBlockerNG, RRD_Summary, Shellcmd, Snort, Speedtest, System_Patches.

              C 1 Reply Last reply Reply Quote 0
              • C
                cinlung @fireodo
                last edited by

                @fireodo said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

                @cinlung said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

                I have been working with 2.6.0 and it was OK with the same settings on the bridge side. After updating to 2.7.0 and even reflash the 2.7.0 RELEASE, the same error persist.

                Your PPPOE settings in extended should look something like that: pppoe.png

                but the Modem should not set any VLAN.

                I did that actually,

                Turn VLAN Off on modem and here is my steps:

                1. Create VLAN 391 and Interface igb0
                2. Create PPPoE using VLAN 391 as the link interface
                3. Set the Assign interface for WAN to PPPoE over VLAN

                I got this error

                Aug 7 22:57:41	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
                Aug 7 22:57:41	ppp	6380	[wan_link0] Link: reconnection attempt 3
                Aug 7 22:57:38	ppp	6380	[wan_link0] Link: reconnection attempt 3 in 3 seconds
                Aug 7 22:57:38	ppp	6380	[wan_link0] LCP: Down event
                Aug 7 22:57:38	ppp	6380	[wan_link0] Link: DOWN event
                Aug 7 22:57:38	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
                Aug 7 22:57:29	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
                Aug 7 22:57:29	ppp	6380	[wan_link0] Link: reconnection attempt 2
                Aug 7 22:57:28	ppp	6380	[wan_link0] Link: reconnection attempt 2 in 1 seconds
                Aug 7 22:57:28	ppp	6380	[wan_link0] LCP: Down event
                Aug 7 22:57:28	ppp	6380	[wan_link0] Link: DOWN event
                Aug 7 22:57:28	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
                Aug 7 22:57:19	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
                Aug 7 22:57:19	ppp	6380	[wan_link0] Link: reconnection attempt 1
                Aug 7 22:57:16	ppp	6380	[wan_link0] Link: reconnection attempt 1 in 3 seconds
                Aug 7 22:57:16	ppp	6380	[wan_link0] LCP: Down event
                Aug 7 22:57:16	ppp	6380	[wan_link0] Link: DOWN event
                Aug 7 22:57:16	ppp	6380	[wan_link0] PPPoE connection timeout after 9 seconds
                Aug 7 22:57:07	ppp	6380	[wan_link0] PPPoE: Connecting to 'INTERNET'
                Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: LayerStart
                Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: state change Initial --> Starting
                Aug 7 22:57:07	ppp	6380	[wan_link0] LCP: Open event
                Aug 7 22:57:07	ppp	6380	[wan_link0] Link: OPEN event
                Aug 7 22:57:07	ppp	6380	[wan] Bundle: Interface ng0 created
                Aug 7 22:57:07	ppp	6380	web: web is not running
                Aug 7 22:57:07	ppp	6380	process 6380 started, version 5.9
                Aug 7 22:57:07	ppp	6380	Multi-link PPP daemon for FreeBSD
                

                One more thing. Doing the step above will break DHCP setting when you revert to DHCP. I had to create PPPoE again in WAN, go to PPP and attach auto create PPP to the igb0 (WAN) save. Then revert to DHCP. This 2.7.0 RELEASE is surely buggy.

                fireodoF 1 Reply Last reply Reply Quote 0
                • fireodoF
                  fireodo @cinlung
                  last edited by

                  @cinlung said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

                  I did that actually,

                  ๐Ÿ˜ž ๐Ÿ˜ž ๐Ÿ˜ž

                  Maybe Steve has an Idea - I do not!

                  Kettop Mi4300YL CPU: i5-4300Y @ 1.60GHz RAM: 8GB Ethernet Ports: 4
                  SSD: SanDisk pSSD-S2 16GB (ZFS) WiFi: WLE200NX
                  pfsense 2.8.0 CE
                  Packages: Apcupsd, Cron, Iftop, Iperf, LCDproc, Nmap, pfBlockerNG, RRD_Summary, Shellcmd, Snort, Speedtest, System_Patches.

                  1 Reply Last reply Reply Quote 0
                  • C
                    cinlung @fireodo
                    last edited by

                    @fireodo said in PPPoE Connection (OVER VLAN) does not work after Upgrade to 2.7.0 Tonight. Please help.:

                    @cinlung

                    And in the Modem you disabled the VLAN setting? (maybe a modem cold start after that)

                    I did. I did not do a cold start. It was not necessary with 2.6.0. I will probably try again tomorrow. Or I might use another non pfsense router to test.

                    1 Reply Last reply Reply Quote 1
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Using something none FreeBSD based as a test would be good.

                      The logs show no reply from the server side at all so either it's not seeinng your requests, pfSense is not seeing the replies, or it's rejecting the requests for some reason.

                      Some ISPs require specific client side identification strings to be sent but nothing there has changed in 2.7.

                      It's possible you're hitting something like this: https://redmine.pfsense.org/issues/12821
                      Though not exactly that since that applied in 2.6 and is fixed in 2.7. That was a change in the igb driver though and might come into play if your ISP is priority tagging.

                      I would try running a packet capture on igb0 dircetly and see if anything is shown coming back from the ISP.

                      Steve

                      C 1 Reply Last reply Reply Quote 0
                      • C
                        cinlung @stephenw10
                        last edited by

                        @stephenw10 I will try to use my TP Link router to check tomorrow. I am not very optimistic on this as it seems nothing more I can do nor any solutions out there.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.