Huawei k5160 4g usb mobile broadband

GiaNN

I also add that if i create a PPP the Huawei LED starts blinking until it reaches purple which should mean that it's connected but you should check the connection if it's active

stephenw10

@GiaNN said in Huawei k5160 4g usb mobile broadband:

if i create a PPP the Huawei LED starts blinking

Create it how?

There's a good chance there are multiple versions of that modem and that they behave differently, Many modems do.

Steve

GiaNN

@stephenw10 through the interfaces GUI, in the section PPP.
Then if i enable the interface the LED starts blinking but it cannot properly start PPP

stephenw10

So you see USB serial ports created? Like cuaU0-3?

GiaNN

@stephenw10 i don't remember, where i see that?
I used as device the /dev/cuau0 and then it started blinking if enabled.

stephenw10

/dev/cuau0 is one of the on-board com ports not the modem. The ports created by a modem are shown with an uppercase 'U' to indicate they are USB connected.

Plug in the modem and then check the system log. If it's recognised you will see log entries showing the new ports created.

GiaNN

@stephenw10 in dmesg shows this:

ugen2.2: <Vodafone (Huawei) Vodafone (Huawei)> at usbus2
umass0 on uhub0
umass0: <Mass Storage> on usbus2
cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
cd0: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
cd0: Serial Number 0123456789ABCDEF
cd0: 40.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd0: quirks=0x10<10_BYTE_ONLY>
da0 at umass-sim0 bus 0 scbus2 target 0 lun 1
da0: <HUAWEI TF CARD Storage 2.31> Removable Direct Access SCSI-2 device
da0: Serial Number 0123456789ABCDEF
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da0: quirks=0x2<NO_6_BYTE>

stephenw10

Ok, so u3g doesn't recognise it. You should see something like:

uhub0: 8 ports with 8 removable, self powered
ugen0.2: <Huawei Technologies Co., Ltd. HUAWEI Mobile> at usbus0
u3g0 on uhub0
u3g0: <Huawei Mobile Connect - Modem> on usbus0
u3g0: Found 5 ports.

If it can work at all it probably needs to be modeswitched. Or reflashed with different firmware.

Note that the OP here never got this modem working, they switched to a different device. And I don't see an entry for it in u3g:
https://github.com/pfsense/FreeBSD-src/blob/devel-main/sys/dev/usb/serial/u3g.c#L339

Steve

GiaNN

@stephenw10 said in Huawei k5160 4g usb mobile broadband:

If it can work at all it probably needs to be modeswitched. Or reflashed with different firmware.

How? i'll make the last try. Then maybe i'll get a different model o try maybe with an OpenWRT VM or something linux based (i tried on Debian and there it's plug & play)

stephenw10

Ok, first thing is to get the USB IDs it's presenting as currently using the usbconfig command:

usbconfig -d ugen2.2 dump_all_desc

GiaNN

@stephenw10 i'm putting it on pastebin because it gets flagged as spam idk why. If there a way to post it without getting it flagged i'll do it.

stephenw10

Aha, it has two config indexes and second one has a coms device interface. Try:

usbconfig -d ugen2.2 set_config 1

See what the system log shows. Or on the console if you're using that directly.

GiaNN

@stephenw10 if i do dmesg it doesn't show anything new after that comand.
And in PPP there's still the default interface

stephenw10

Hmm, it really showed nothing in the system log?

That other config doesn't have com ports but it should have exposed the USB Ethernet interface, ue0. That should be in the log.

Try: usbconfig -d ugen2.2 dump_curr_config_desc

Make sure it shows config index 1.

GiaNN

@stephenw10 this is the dump it should be on config index 1.
This is dmesg since i inserted the Huawei there's nothing new after the comand:

ugen2.2: <Vodafone (Huawei) Vodafone (Huawei)> at usbus2
umass0 on uhub0
umass0: <Mass Storage> on usbus2
cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
cd0: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
cd0: Serial Number 0123456789ABCDEF
cd0: 40.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd0: quirks=0x10<10_BYTE_ONLY>
da0 at umass-sim0 bus 0 scbus2 target 0 lun 1
da0: <HUAWEI TF CARD Storage 2.31> Removable Direct Access SCSI-2 device
da0: Serial Number 0123456789ABCDEF
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da0: quirks=0x2<NO_6_BYTE>
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 c1 00 00 04 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59c1
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 fe 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59fe
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 fe 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59fe
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 c1 00 00 04 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59c1
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 fe 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59fe
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 fe 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59fe
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back
(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 ff 00 00 01 00 
(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
(cd0:umass-sim0:0:0:0): Info: 0x59ff
(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
(cd0:umass-sim0:0:0:0): cddone: got error 0x5 back

And this is a screenshot of the syslog maybe it's easier to read

stephenw10

Hmm, odd it shows config index 1 in the output. But nothing new was logged? Those logs all appear to be ~20mins old.

Try running ifconfig, do you see a ue0 interface?

GiaNN

@stephenw10 yes i put only the log after i inserted the Huawei, after i did that command nothing new showed up, now i've removed it and reinserted back, did usbconfig -d ugen2.2 set_config 1 and if i do ifconfig the new interface is this:

ppp1: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: OPT1
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

And maybe this

enc0: flags=0<> metric 0 mtu 1536
	groups: enc
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

the other are re0 my LAN, em0 my WAN
this is the entire list without the IPs

ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN
	options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
	ether 90:1b:0e:87:da:fa
	inet6 fe80::921b:eff:fe87:dafa%re0 prefixlen 64 scopeid 0x1
	inet6  prefixlen 64
	inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
	media: Ethernet autoselect (1000baseT <full-duplex>)
	status: active
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
em0: flags=8863<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1410
	options=481209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>
	ether 1c:fd:08:70:a0:88
	inet6 fe80::1efd:8ff:fe70:a088%em0 prefixlen 64 scopeid 0x2
	media: Ethernet autoselect (1000baseT <full-duplex>)
	status: active
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0<> metric 0 mtu 1536
	groups: enc
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
	inet6 ::1 prefixlen 128
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
	inet 127.0.0.1 netmask 0xff000000
	groups: lo
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
pflog0: flags=100<PROMISC> metric 0 mtu 33152
	groups: pflog
pfsync0: flags=0<> metric 0 mtu 1500
	maxupd: 128 defer: off
	syncok: 1
	groups: pfsync
ovpns1: flags=8043<UP,BROADCAST,RUNNING,MULTICAST> metric 0 mtu 1500
	options=80000<LINKSTATE>
	inet6 fe80::921b:eff:fe87:dafa%ovpns1 prefixlen 64 scopeid 0x8
	inet6  prefixlen 64
	inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255
	groups: tun openvpn
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	Opened by PID 27828
ovpns2: flags=8043<UP,BROADCAST,RUNNING,MULTICAST> metric 0 mtu 1500
	options=80000<LINKSTATE>
	inet6 fe80::921b:eff:fe87:dafa%ovpns2 prefixlen 64 scopeid 0x9
	inet6  prefixlen 64
	inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255
	groups: tun openvpn
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	Opened by PID 47091
pppoe0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> metric 0 mtu 1402
	description: 
	inet6 fe80::921b:eff:fe87:dafa%pppoe0 prefixlen 64 scopeid 0x7
	inet  netmask 0xffffffff
	nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
ppp1: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: OPT1
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

If it's useful i'm on PFsense+ 23.05.1-RELEASE

stephenw10

Hmm, curious. Testing that here in 23.05.1 it applies imediately:

Sep 18 14:07:58 	kernel 		ue0: Ethernet address: 02:1e:10:1f:00:00
Sep 18 14:07:58 	kernel 		ue0: <USB Ethernet> on cdce0
Sep 18 14:07:58 	kernel 		cdce0: <CDC Ethernet Control Model (ECM)> on usbus0
Sep 18 14:07:58 	kernel 		cdce0 on uhub0
Sep 18 14:07:58 	kernel 		u3g0: detached
Sep 18 14:07:58 	kernel 		u3g0: at uhub0, port 4, addr 1 (disconnected)

If you replug the modem into the port does it go back to config index 0?

It could be the index 1 interfaces are still not recognised but I would expect something because the virtual cd drive not present in index 1.

Other things you can try are; ejecting the virtual CD drive. Or using usbmodeswitch directly.

cdcontrol eject

GiaNN

@stephenw10 if i replug it, there's still config index 1
if i do cdcontrol eject nothing seems to happen

Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): Error 5, Unretryable error
Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): Info: 0x59c1
Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): SCSI sense: MEDIUM ERROR asc:11,0 (Unrecovered read error)
Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): SCSI status: Check Condition
Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): CAM status: SCSI Status Error
Sep 18 15:57:41 	kernel 		(cd0:umass-sim0:0:0:0): READ(10). CDB: 28 00 00 00 59 c1 00 00 04 00
Sep 18 15:57:35 	kernel 		da0: quirks=0x2<NO_6_BYTE>
Sep 18 15:57:35 	kernel 		da0: Attempt to query device size failed: NOT READY, Medium not present
Sep 18 15:57:35 	kernel 		da0: 40.000MB/s transfers
Sep 18 15:57:35 	kernel 		da0: Serial Number 0123456789ABCDEF
Sep 18 15:57:35 	kernel 		da0: <HUAWEI TF CARD Storage 2.31> Removable Direct Access SCSI-2 device
Sep 18 15:57:35 	kernel 		da0 at umass-sim0 bus 0 scbus2 target 0 lun 1
Sep 18 15:57:35 	kernel 		cd0: quirks=0x10<10_BYTE_ONLY>
Sep 18 15:57:35 	kernel 		cd0: Attempt to query device size failed: NOT READY, Medium not present
Sep 18 15:57:35 	kernel 		cd0: 40.000MB/s transfers
Sep 18 15:57:35 	kernel 		cd0: Serial Number 0123456789ABCDEF
Sep 18 15:57:35 	kernel 		cd0: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
Sep 18 15:57:35 	kernel 		cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Sep 18 15:57:35 	kernel 		umass0: <Mass Storage> on usbus2
Sep 18 15:57:35 	kernel 		umass0 on uhub0
Sep 18 15:57:35 	kernel 		ugen2.2: <Vodafone (Huawei) Vodafone (Huawei)> at usbus2

If i want to try with usbmodeswitch how should i do?

stephenw10

So it still showed it was using config index 1 after replugging? That's surprising.

Yes, you can try usb_modeswitch. Install the pkg like:

[23.05.1-RELEASE][admin@6100.stevew.lan]/root: pkg install usb_modeswitch
Updating pfSense-core repository catalogue...
pfSense-core repository is up to date.
Updating pfSense repository catalogue...
pfSense repository is up to date.
All repositories are up to date.
The following 1 package(s) will be affected (of 0 checked):

New packages to be INSTALLED:
	usb_modeswitch: 2.6.0 [pfSense]

Number of packages to be installed: 1

64 KiB to be downloaded.

Proceed with this action? [y/N]: y
[1/1] Fetching usb_modeswitch-2.6.0.pkg: 100%   64 KiB  65.8kB/s    00:01    
Checking integrity... done (0 conflicting)
[1/1] Installing usb_modeswitch-2.6.0...
[1/1] Extracting usb_modeswitch-2.6.0: 100%
[23.05.1-RELEASE][admin@6100.stevew.lan]/root: rehash

https://man.freebsd.org/cgi/man.cgi?query=usb_modeswitch