Implemented IPV6...Still Feel Left in the Dark!

[Gertjan]

@NollipfSense

Compare your :

with my :

Your DHCPv6 server hasn't a prefix (see Subnet) to work with ....

Check the DHCP6c on the WAN side (activate "DHCP6 Debug" on System>Advanced>Networking ) to be sure you obtained a (at least one) prefix.

[NollipfSense]

@JKnott said in Implemented IPV6...Still Feel Left in the Dark!:

I've been running pfSense, including with IPv6 for almost 8 years and it works well for me.

@Gertjan said in Implemented IPV6...Still Feel Left in the Dark!:

to be sure you obtained a (at least one) prefix.

For some unknown reason, it only started working after I configure from the cmdline...all is good...

[NollipfSense]

@Gertjan said in Implemented IPV6...Still Feel Left in the Dark!:

Your DHCPv6 server hasn't a prefix (see Subnet) to work with ....

How did you get your DHCPv5 server to show the WAN IP...had it in post #8 above. I am trying to get DHCPv6 server to work alongside RA; however, mine is showing my ULA IP and every range appears either outside the specified range, even with default :1000 - :2000 or a valid range must be specified...I am doing something wrong if I have 65,536 available...I put :0000:0009 - :0000:0154 or ::009 - ::0154 and I have ULA IP:: - ULA IP:0:ffff:ffff:ffff:ffff available range.

[Gertjan]

@NollipfSense said in Implemented IPV6...Still Feel Left in the Dark!:

How did you get your DHCPv5 server to show the WAN IP

After :
Set WAN to DHCP6 and just one setting in the "DHCPv6 Prefix Delegation size" : /64
Set the LAN interface up to tracking, where "Track IPv6 Interface" is set to WAN and selected

"0" here (no choice, just one prefix)

Now, when I activate the LAN DHCPv6 server, the prefix is shown as I've shown above, as it is known upfront : Delegated Prefix: WAN/0 (2a01:cb19:beef:a6dc::/64) : selected prefix "0" from the available 'range" (just 1 or 0 from 0) = 2a01:cb19:beef:a6dc:: with a standard /64 size.
The whole goal of using the DHCPv6 server is that is shouldn't use 'ULA" IPv6 .... (AFAIK).
The pfSense LAN (OPTx) DHCPv6 server should be one of the assigned (on the LAN/OPTx settings page) assigned to pfSense by an upstream DHCPv6 server, like my ISP router. Or it could even come from much farther upstream, your ISP equipment.
This obtained - by the pfSense WAN DHCPc6 client - prefix should be shown in the DHCP logs.

[NollipfSense]

@Gertjan It seems that my problem is that it does not show the Delegated Prefix despite DCHPv6 is enabled showing W/0...no IPv6 IP...then device gets an IPv6 IP despite Dashboard shows no LAN IPv6 IP...firewall shows no traversal...only if configure LAN interface via cmdline does it work but that uses the ULA...I did enabled IPv6 debug...

[Gertjan]

@NollipfSense said in Implemented IPV6...Still Feel Left in the Dark!:

I did enabled IPv6 debug...

dhcp6c logs ?

Like these : (read from bottom to top - it all happens in less then 30 ms)

2023-10-17 14:53:45.531447+02:00 	dhcp6c 	6769 	got an expected reply, sleeping.
2023-10-17 14:53:45.531395+02:00 	dhcp6c 	6769 	removing an event on ix3, state=RENEW
2023-10-17 14:53:45.531316+02:00 	dhcp6c 	6769 	script "/var/etc/dhcp6c_wan_script.sh" terminated
2023-10-17 14:53:45.530464+02:00 	dhcp6c 	68882 	dhcp6c renew, no change - bypassing update on ix3
2023-10-17 14:53:45.524339+02:00 	dhcp6c 	6769 	executes /var/etc/dhcp6c_wan_script.sh
2023-10-17 14:53:45.524316+02:00 	dhcp6c 	6769 	update a prefix 2a01:cb19:beef:a6dc::/64 pltime=600, vltime=1800
2023-10-17 14:53:45.524284+02:00 	dhcp6c 	6769 	update an IA: PD-0
2023-10-17 14:53:45.524261+02:00 	dhcp6c 	6769 	Domain search list[0] home.
2023-10-17 14:53:45.524238+02:00 	dhcp6c 	6769 	nameserver[0] 2a01:cb19:907:a600:46d4:54ff:fe2a:3600
2023-10-17 14:53:45.524202+02:00 	dhcp6c 	6769 	dhcp6c Received INFO
2023-10-17 14:53:45.524179+02:00 	dhcp6c 	6769 	get DHCP option domain search list, len 6
2023-10-17 14:53:45.524158+02:00 	dhcp6c 	6769 	get DHCP option DNS, len 16
2023-10-17 14:53:45.524139+02:00 	dhcp6c 	6769 	preference: 255
2023-10-17 14:53:45.524119+02:00 	dhcp6c 	6769 	get DHCP option preference, len 1
2023-10-17 14:53:45.524094+02:00 	dhcp6c 	6769 	IA_PD prefix: 2a01:cb19:beef:a6dc::/64 pltime=600 vltime=1800
2023-10-17 14:53:45.524068+02:00 	dhcp6c 	6769 	get DHCP option IA_PD prefix, len 25
2023-10-17 14:53:45.524048+02:00 	dhcp6c 	6769 	IA_PD: ID=0, T1=300, T2=480
2023-10-17 14:53:45.524028+02:00 	dhcp6c 	6769 	get DHCP option IA_PD, len 41
2023-10-17 14:53:45.524008+02:00 	dhcp6c 	6769 	DUID: 00:03:00:01:44:d4:54:2a:36:00
2023-10-17 14:53:45.523982+02:00 	dhcp6c 	6769 	get DHCP option server ID, len 10
2023-10-17 14:53:45.523961+02:00 	dhcp6c 	6769 	DUID: 00:01:00:01:2b:5a:d7:6b:90:ec:77:29:39:2c
2023-10-17 14:53:45.523929+02:00 	dhcp6c 	6769 	get DHCP option client ID, len 14
2023-10-17 14:53:45.523896+02:00 	dhcp6c 	6769 	receive reply from fe80::46d4:54ff:fe2a:3600%ix3 on ix3
2023-10-17 14:53:45.505302+02:00 	dhcp6c 	6769 	send renew to ff02::1:2%ix3
2023-10-17 14:53:45.504977+02:00 	dhcp6c 	6769 	set IA_PD
2023-10-17 14:53:45.504957+02:00 	dhcp6c 	6769 	set IA_PD prefix
2023-10-17 14:53:45.504934+02:00 	dhcp6c 	6769 	set option request (len 4)
2023-10-17 14:53:45.504912+02:00 	dhcp6c 	6769 	set elapsed time (len 2)
2023-10-17 14:53:45.504893+02:00 	dhcp6c 	6769 	set server ID (len 10)
2023-10-17 14:53:45.504873+02:00 	dhcp6c 	6769 	set client ID (len 14)
2023-10-17 14:53:45.504848+02:00 	dhcp6c 	6769 	a new XID (806046) is generated
2023-10-17 14:53:45.504824+02:00 	dhcp6c 	6769 	Sending Renew
2023-10-17 14:53:45.504791+02:00 	dhcp6c 	6769 	reset a timer on ix3, state=RENEW, timeo=0, retrans=9648
2023-10-17 14:53:45.504702+02:00 	dhcp6c 	6769 	IA timeout for PD-0, state=ACTIVE

It looks a bit like DHCPv4 : the client set some options, and fires a request to the server.
Identification isn't MAC based, but "dude" (DUID) based.
"2a01:cb19:beef:a6dc::/64" is the prefix pfSense received - and is used for the DHCPv6 server on LAN.

[NollipfSense]

@Gertjan

Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::9)
Oct 17 08:53:03 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 08:53:03 dhcp6c 19566 get DHCP option IA_PD, len 18
Oct 17 08:53:03 dhcp6c 19566 IA_PD: ID=0, T1=0, T2=0
Oct 17 08:53:03 dhcp6c 19566 get DHCP option status code, len 2
Oct 17 08:53:03 dhcp6c 19566 status code: no prefixes
Oct 17 08:53:03 dhcp6c 19566 server ID: 00:03:00:01:54:47:cc:30:05:31, pref=-1
Oct 17 08:53:03 dhcp6c 19566 advertise contains no address/prefix
Oct 17 08:53:07 dhcpd 27048 Internet Systems Consortium DHCP Server 4.4.3-P1
Oct 17 08:53:07 dhcpd 27048 Copyright 2004-2022 Internet Systems Consortium.
Oct 17 08:53:07 dhcpd 27048 All rights reserved.

I shall try rebooting the modem...

[NollipfSense]

@Gertjan Restarted the modem...

Oct 17 09:00:59 dhcp6c 19566 duplicated DNS address (fd00:976a::10)
Oct 17 09:00:59 dhcp6c 19566 get DHCP option IA_PD, len 18
Oct 17 09:00:59 dhcp6c 19566 IA_PD: ID=0, T1=0, T2=0
Oct 17 09:00:59 dhcp6c 19566 get DHCP option status code, len 2
Oct 17 09:00:59 dhcp6c 19566 status code: no prefixes
Oct 17 09:00:59 dhcp6c 19566 server ID: 00:03:00:01:54:47:cc:30:05:31, pref=-1
Oct 17 09:00:59 dhcp6c 19566 advertise contains no address/prefix
Oct 17 09:02:50 dhcp6c 19566 Sending Solicit
Oct 17 09:02:50 dhcp6c 19566 set client ID (len 14)
Oct 17 09:02:50 dhcp6c 19566 set elapsed time (len 2)
Oct 17 09:02:50 dhcp6c 19566 set option request (len 4)
Oct 17 09:02:50 dhcp6c 19566 set IA_PD prefix
Oct 17 09:02:50 dhcp6c 19566 set IA_PD
Oct 17 09:02:50 dhcp6c 19566 send solicit to ff02::1:2%vtnet0
Oct 17 09:02:50 dhcp6c 19566 reset a timer on vtnet0, state=SOLICIT, timeo=11, retrans=120720
Oct 17 09:02:50 dhcp6c 19566 receive advertise from fe80::5647:ccff:fe30:531%vtnet0 on vtnet0
Oct 17 09:02:50 dhcp6c 19566 get DHCP option server ID, len 10
Oct 17 09:02:50 dhcp6c 19566 DUID: 00:03:00:01:54:47:cc:30:05:31
Oct 17 09:02:50 dhcp6c 19566 get DHCP option client ID, len 14
Oct 17 09:02:50 dhcp6c 19566 DUID: 00:01:00:01:2c:b2:0d:3d:36:62:bf:c7:26:75
Oct 17 09:02:50 dhcp6c 19566 get DHCP option opt_82, len 4
Oct 17 09:02:50 dhcp6c 19566 unknown or unexpected DHCP6 option opt_82, len 4
Oct 17 09:02:50 dhcp6c 19566 get DHCP option DNS, len 256

[Gertjan]

@NollipfSense said in Implemented IPV6...Still Feel Left in the Dark!:

advertise contains no address/prefix

I presume that the other side said : "sorry, no prefixes for you".

My example a both is just a 'renew' from what was already obtained.
I do see the setup part

2023-10-17 14:53:45.504977+02:00 	dhcp6c 	6769 	set IA_PD
2023-10-17 14:53:45.504957+02:00 	dhcp6c 	6769 	set IA_PD prefix
2023-10-17 14:53:45.504934+02:00 	dhcp6c 	6769 	set option request (len 4)
2023-10-17 14:53:45.504912+02:00 	dhcp6c 	6769 	set elapsed time (len 2)
2023-10-17 14:53:45.504893+02:00 	dhcp6c 	6769 	set server ID (len 10)
2023-10-17 14:53:45.504873+02:00 	dhcp6c 	6769 	set client ID (len 14)

which includes the question "a prefix for me please".

Yours doesn't show that. And "not asked" is "not getting".

Another xample :
I've :
IA_PD: ID=0, T1=300, T2=480
You :
IA_PD: ID=0, T1=0, T2=0

And this one goes without comment :
status code: no prefixes

Still : my dhcp6c clients settings :

with just one explanation : I've set "/64" and that's it. No other options.

Not that it really matters, but where is the upstream dhcp6 server ? An ISP router ?
At the ISP side ?

Be aware : if you have even the slightest thoughts that your ISP isn't IPv6-ready jet, do not forget the he.net option.
It's free, probably not the speediest one, but it works as advertised. You get a static /48 (that a lot of prefixes ...) I've been using them for many years.
No 'tracking' needed : you assign static IPv6 /4 to every LAN and done.
If needed, set up a DHCPv6 server on every LAN with a pool in the prefix of that LAN, and you're good.

[NollipfSense]

@Gertjan Wow, I thought, according to the instructions I followed, I needed to enable these:

[JKnott]

@NollipfSense

If you only request an IPv6 prefix, you will not get an IPv6 address on your WAN port. That's not a problem, but makes it easier to use a VPN, etc. if you have one. So, if your ISP provides a WAN address, you might as well use it. Your prefix delegation size should be whatever your ISP provides. Mine provides a /56 prefix, so I put 56 in that box.

[NollipfSense]

@Gertjan said in Implemented IPV6...Still Feel Left in the Dark!:

but where is the upstream dhcp6 server ? An ISP router ?
At the ISP side ?

Either I am not asking or the ISP (T-Mobile/Fast 5688w)

Oct 17 09:53:39 dhcp6c 22871 Sending Solicit
Oct 17 09:53:39 dhcp6c 22871 set client ID (len 14)
Oct 17 09:53:39 dhcp6c 22871 set identity association
Oct 17 09:53:39 dhcp6c 22871 set elapsed time (len 2)
Oct 17 09:53:39 dhcp6c 22871 set option request (len 4)
Oct 17 09:53:39 dhcp6c 22871 set IA_PD
Oct 17 09:53:39 dhcp6c 22871 send solicit to ff02::1:2%vtnet0
Oct 17 09:53:39 dhcp6c 22871 reset a timer on vtnet0, state=SOLICIT, timeo=2, retrans=3915
Oct 17 09:53:43 dhcp6c 22871 Sending Solicit
Oct 17 09:53:43 dhcp6c 22871 set client ID (len 14)
Oct 17 09:53:43 dhcp6c 22871 set identity association
Oct 17 09:53:43 dhcp6c 22871 set elapsed time (len 2)
Oct 17 09:53:43 dhcp6c 22871 set option request (len 4)
Oct 17 09:53:43 dhcp6c 22871 set IA_PD
Oct 17 09:53:43 dhcp6c 22871 send solicit to ff02::1:2%vtnet0
Oct 17 09:53:43 dhcp6c 22871 reset a timer on vtnet0, state=SOLICIT, timeo=3, retrans=7534
Oct 17 09:53:51 dhcp6c 22871 Sending Solicit
Oct 17 09:53:51 dhcp6c 22871 set client ID (len 14)
Oct 17 09:53:51 dhcp6c 22871 set identity association
Oct 17 09:53:51 dhcp6c 22871 set elapsed time (len 2)
Oct 17 09:53:51 dhcp6c 22871 set option request (len 4)
Oct 17 09:53:51 dhcp6c 22871 set IA_PD
Oct 17 09:53:51 dhcp6c 22871 send solicit to ff02::1:2%vtnet0
Oct 17 09:53:51 dhcp6c 22871 reset a timer on vtnet0, state=SOLICIT, timeo=4, retrans=14941
Oct 17 09:54:06 dhcp6c 22871 Sending Solicit
Oct 17 09:54:06 dhcp6c 22871 set client ID (len 14)
Oct 17 09:54:06 dhcp6c 22871 set identity association
Oct 17 09:54:06 dhcp6c 22871 set elapsed time (len 2)
Oct 17 09:54:06 dhcp6c 22871 set option request (len 4)
Oct 17 09:54:06 dhcp6c 22871 set IA_PD

[Gertjan]

@NollipfSense

Thats a lot "solicits" without any answer.

Do you have a link about your ISP's instructions ?

[NollipfSense]

@JKnott This is my prefix according to my ISP DHCPv6: 2607:fd90:d591:4ef3::/64

Where could I manually input this?

[NollipfSense]

@Gertjan Going to look up...will be holding for 1/2 hr to speak with the ISP support.

[NollipfSense]

@Gertjan said in Implemented IPV6...Still Feel Left in the Dark!:

Do you have a link about your ISP's instructions

The Bad news - the T-Mobile Fast 5688w does not support passing the prefix...I get a IPv6/64 but it's one single IP.

[JKnott]

@NollipfSense said in Implemented IPV6...Still Feel Left in the Dark!:

I get a IPv6/64 but it's one single IP.

With Rogers, I get 1 address on the phone, but a /64 prefix for tethered devices. I can tether via WiFi or USB.

[NollipfSense]

@JKnott What if I add the prefix...but it seems that the ISP changes the IPv6 frequently...where would I add the static address manually or use a IPv6 bridge to the ULA? I can add static IPv6 for IPv6 configuration type...

[JKnott]

@NollipfSense

I assume your ISP uses DHCPv6-PD, unless they tell you otherwise. Is that what you do? You do not normally add the prefix manually. Have you called your ISP's support? They can tell you better than we can.

[NollipfSense]

@JKnott said in Implemented IPV6...Still Feel Left in the Dark!:

Have you called your ISP's support?

Yes, that's how I got the supposed news. Then, they offered a Cradlepoint 300...first, they said it's the same $55/mth but a onetime $75 charge for the modem. So, I said okay and went to checkout...the modem is free but $85/mth. I said stop, bye.

Apparently, the modem needs to have two lines, one for data and the other to pass the IPv6 prefix, hence, two sims and why the Fast5688w would not work having one line...