How To Disable/Enable Energy Efficient Ethernet (EEE)?
-
OK and still no link losses logged? Just gateway alarms?
What about the interface stats in Status > Interfaces? Does it show errors, dropped packets? How about in the output of
netstat -idirectly? -
MTU 1492 In/out packets 27805509/14754894 (27.99 GiB/6.21 GiB) In/out packets (pass) 27805509/14754894 (27.99 GiB/6.21 GiB) In/out packets (block) 5606/0 (222 KiB/0 B) In/out errors 0/0 Collisions 0netstat -i
Ierrs/Idrop/Oerrsare all0or- -
On the parent NIC? Both?
-
@stephenw10 here is a more detailed look:
-
No errors or drops on anything then. Which NICs are the PPPoE WANs using?
Could just be something upstream like a bad modem.
-
@stephenw10 icg1 & icg2. Yeah, it could be what are the chances they are both problematic and both drop at the same exact time?
-
Same ISP?
-
@stephenw10 different ISP, different modem make, and different tech (adsl vs fiber)
-
Hmm, very unlikely then. So neither NIC ever loses link. The PPPoE sessions do not get disconnected. The PPPoE connections simply stop passing traffic.
Do you see it logging missing LCP echos in the ppp log when this happens? It has to drop 5 before the ppp link is restarted and that doesn't appear to be happening but if the NICs stop passing traffic it would drop some LCP packets.
Do you have access to the modems on a private IP at all? You could assign the parent interfaces with those IPs as gateway and they would then be monitored separately to the PPP link.
-
@stephenw10 said in How To Disable/Enable Energy Efficient Ethernet (EEE)?:
Do you see it logging missing LCP echos in the ppp log when this happens
No. In 10 days of PPP logs, I only see a single "LCP: no reply to 1 echo request"
Do you have access to the modems on a private IP at all
no. One modem doesn't have a web interface afaik, and the other is being used in bridge mode (so the router doesnt do any tcp/ip stuff with it, as I understand)
-
@lazyt said in How To Disable/Enable Energy Efficient Ethernet (EEE)?:
No. In 10 days of PPP logs, I only see a single "LCP: no reply to 1 echo request"
Hmm, and the ppp sessions remain up on both WANs?
And I assume you saw multiple WAN alarms during that time?
-
@stephenw10 said in How To Disable/Enable Energy Efficient Ethernet (EEE)?:
And I assume you saw multiple WAN alarms during that time?
sure, tons
-
@stephenw10 said in How To Disable/Enable Energy Efficient Ethernet (EEE)?:
Hmm, and the ppp sessions remain up on both WANs?
Importantly that? ^ The uptime on both WANs shows they never disconnected?
If that's the case this looks like something completely different. Like maybe it lost routing. Or something hung whilst reloading the filter maybe. I would expect to see something logged in either case though.
-
L lazyt referenced this topic on
-
@stephenw10 thank you so much for your help! I'm nearing the end of my rope with these disconnects (as are my Zoom colleagues), and I think I'll just try a new box. Thanks so much!!
-
Hi sorry for asking for this to be simplified but apparently virgin media has broken there 2.5gig port with the latest firmware for the hub5 the thread on the forums say it is due to eee and would like to test this but so far can’t find out how to get info if it is enabled or not, am using an intel x710 card
Currently on pfsense 23.09-1
Can someone list the commands needed to get info about that state of eee my card is listed as ixl0 and ixl1, 0 is the wan port
Thread for virgin media https://community.virginmedia.com/t5/Tech-Chatter/Hub-5-Firmware-Upgrade/td-p/5480079/page/2
-
On ixl it is set by:
[24.03-BETA][admin@7100.stevew.lan]/root: sysctl -d dev.ixl.0.eee.enable dev.ixl.0.eee.enable: Enable Energy Efficient Ethernet (EEE) [24.03-BETA][admin@7100.stevew.lan]/root: sysctl dev.ixl.0.eee.enable dev.ixl.0.eee.enable: 0You can also check to see if it's sending or receiving LPI symbols:
[24.03-BETA][admin@7100.stevew.lan]/root: sysctl dev.ixl.0.eee dev.ixl.0.eee.rx_lpi_count: 0 dev.ixl.0.eee.tx_lpi_count: 0 dev.ixl.0.eee.rx_lpi_status: 0 dev.ixl.0.eee.tx_lpi_status: 0 dev.ixl.0.eee.enable: 0Steve
-
thanks for that
would i be correct in saying that eee is enabled?
sysctl dev.ixl.0.eee
dev.ixl.0.eee.rx_lpi_count: 1205843
dev.ixl.0.eee.tx_lpi_count: 1448892
dev.ixl.0.eee.rx_lpi_status: 1
dev.ixl.0.eee.tx_lpi_status: 1
dev.ixl.0.eee.enable: 1 -
Yes that's enabled and it's both seeing and ending LPI.
-
This post is deleted! -
okay so managed to disable it but doesn't seem to be persistant through a reboot, but turning it off does solve the virgin media problem, just need to make it permament now
to disable it i had to use sysctl dev.ixl.0.eee.enable:0
and adding dev.ixl.0.eee.enable as a system tunable and a value of 0 survives a reboot :)
