pfSense on Watchguard M370
-
@nicknitro
Hey Nick,
How did you go about installing exsi on a headless system?
I tried setting up a kickstarter file using this guide: https://www.virten.net/2014/12/unattended-esxi-installations-from-an-usb-flash-drive/
and setting up the serial console using parts from here: www.vmwareadmins.com/installing-esxi-serial-console-headless-video-card/
I can boot from USB but when it installs it cant seem to find any fixed disks and then installs to the USB stick, my guess is drivers but have you got any idea what I need to add to the iso at all?
-
Esxi 6.5 is the latest you can install..maybe 6.7. Definitely not 7.0 as that version does not support the sata ports.
I ran esxi 6.5 from usb. Used the msata to store iso's and sata ssd's to store the vm's
I switched to proxmox 8.0. Got a custom debian iso from https://fai-project.org/FAIme/# that gives an auto headless install with ssh. After that enable serial console and add the proxmox
https://pve.proxmox.com/wiki/Install_Proxmox_VE_on_Debian_11_Bullseye and you are on your way. -
Ah thats where I was going wrong then! I started off with 8.0 then 7.0 but nothing below that i'll give 6.7 a go, let people know how I get on, thanks again and for the heads up for promox too.
-
@tapnet said in pfSense on Watchguard M370:
Ah thats where I was going wrong then! I started off with 8.0 then 7.0 but nothing below that i'll give 6.7 a go, let people know how I get on, thanks again and for the heads up for promox too.
Just wanted to update on this.
6.7 installs fine works really well, I would recommend using a Kickstarter file for unnattneded access.
I upgrade the CPU with a i5 7600k without needing to make any changes to bios or microcode. I am still running on the standard bios.
Now just need to configure virtual pfsense and retire my USG-3P thanks again.
-
Did you or anyone get anywhere with this? I have a female to female pcie cable and a Intel X530-DA2 card I can see the card powering on and evidence of life in unfi but its not being seen at all by esxi I tried all in the latest VIB file from vmware but its being superseeded so wont install
I am going to make a 3d printed enclosure for the card so it wont just sit out the case like that :) -
@tapnet said in pfSense on Watchguard M370:
evidence of life in unfi
What exactly are you seeing there?
-
Hi ,
I am trying to upgrade the MSATA drive in these from the 16Gb supplied to 256Gb.
I know it is overkill but it is giving me CAM errors and write delayed errors, along with operation not permitted errors ATA retry command exhausted.
This is not a new drive, I had the same errors with a second hand 128Gb one.
I have destroyed the partitions and the drive should be blank.
But I get the same error messages each time.
I booted system rescue cd over serial and examined the drive whilst in the WatchGuard. Smartmon tools find the driver healthy with no errors.
I am going to try a 2.5 120Gb SSD instead of the MSATA, but I will have to order one in.
Any advise on anything else to try? Everything installs fine on the original 16GB Transcend.
-
CAM errors like that are almost always a bad drive or drive controller. Do you have the exact error you were seeing?
-
@stephenw10 said in pfSense on Watchguard M370:
CAM errors like that are almost always a bad drive or drive controller. Do you have the exact error you were seeing?
It's during the installer stage.
Everything installs fine with the original 16gb.
Anyway of capturing the installer data or do I need to manually write it down else where?
But from what I recall you choose zfs auto and it immediately says operation not permitted.
When you try and create a ufs system the drive spews these ATA timeout cam errors.
I booted system rescue cd over serial and ran smartmon tools and they pass the drive after a health check.
I agree that errors like this are normally a bad drive, just wondering if the msata port has a max drive limit?
-
I'm not aware of a limit. 256GB isn't especially large.
Can you not copy/paste the error from the terminal during the install? Or grab a screenshot?
-
@stephenw10 said in pfSense on Watchguard M370:
I'm not aware of a limit. 256GB isn't especially large.
Can you not copy/paste the error from the terminal during the install? Or grab a screenshot?
Possibly but the screen rolls the error and returns to the installer screen.
I can definitely get the data from smartmon tools.
I have just ordered an 120gb msata and another 2.5 120gb ssd.
That will give me enough new parts to test with.
-
@stephenw10 said in pfSense on Watchguard M370:
I'm not aware of a limit. 256GB isn't especially large.
Can you not copy/paste the error from the terminal during the install? Or grab a screenshot?
Ok terminal errors:
ada0:ahcich1:0:0:0): CAM status: ATA Status Error (ada0:ahcich1:0:0:0): ATA status: 00 () (ada0:ahcich1:0:0:0): RES: 00 00 00 00 00 00 00 00 00 00 00 (ada0:ahcich1:0:0:0): Error 5, Retries exhausted Input/output error GPT boot partition write failed gpart: Input/output error (ada0:ahcich1:0:0x Initializ Input/output error (ada0:ahcich1:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 10 40 00 00 40 00 00 00 00 00 00u wait. (ada0:ahcich1:0:0:0): CAM status: Auto-Sense Retrieval Failed (ada0:ahcich1:0:0:0): Error 5, Unretryable error Smartmon Tools output === START OF INFORMATION SECTION === Device Model: SAMSUNG SSD SM841 SED mSATA 256GB LU WWN Device Id: 5 002538 500000000 Firmware Version: DXM44D6Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 27 16:32:08 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (53956) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 1571 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 088 088 005 - 420 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 9152 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 241 Total_LBAs_Written -O--CK 099 099 000 - 17757354518 242 Total_LBAs_Read -O--CK 099 099 000 - 53456616621 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6100 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 40/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2024-03-27 14:25 ? - ... ..(125 skipped). .. - 127 2024-03-27 16:31 ? - 0 2024-03-27 16:32 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC -
Hmm, that error sure looks like a bad drive. But it could be some low level compatibility issue with the drive controller.
-
@stephenw10 said in pfSense on Watchguard M370:
Hmm, that error sure looks like a bad drive. But it could be some low level compatibility issue with the drive controller.
I have ordered a brand new 120GB MSATA and a 120GB 2.5" SSD.
As both of the MSATA drives I have tried are second hand I have no history and can only go by the data.Odd thing that the smart data says healthy but I have seen a nearly dead drive reported as good before, so I always take the results it gives with a pinch of salt.
If I had an MSATA adapter I could try testing the drive on another machine but the M370 is the only MSATA device I have.
-
Mmm, I've got an m.2 SATA drive here that behaves similarly. It usually allows an install but throws errors continually. Shows as good in tests, though with a lot of ware. I wouldn't trust it with anything vaguely important! Odd to see the same on two drives though.
-
The other one was showing errors about read write and invalid geometry and invalid primary GPT using secondary. Even writing DD zeros to it produced errors.
Unfortunately I can not test that one anymore as I no longer have it to test.
-
@HangmansNoose001380 Can you DM me the BIOS-File?.
BigThx
-
Can anyone DM me the unlock password bios please?
-
Sent.
-
@kapook00789 Me too! TNX!
