SG3100 Does not boot after latest update
-
I took latest update today and now I have a dead switch
General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6820 High speed PHY - Version: 2.0 Init Customer board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 3 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 3 | SATA1 | | 3 | 4 | SGMII2 | | 4 | 5 | PCIe1 | | 5 | 5 | USB3 HOST1 | ------------------------------- PCIe Ref. Clock Buffer Control is 0xf00015bf, setting to 0xf00015bf SOC_CONTROL_REG1 is 0xf00015bf, setting to 0x0707c0f3 PCIe, Idx 0: detected no link PCIe, Idx 1: detected no link High speed PHY - Ended Successfully mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Oct 8 2018 - 12:59:22) DDR4 Training Sequence - Switching XBAR Window to FastPath Window mv_ddr: completed successfully __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel-17.06.0 Board: Rogue-1 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 250 [MHz] DDR4 @ 800 [MHz] DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB MMC: mv_sdh: 0 DBG: Calling spi_flash_probe from env_relocate_spec() SF: Probing bus 0 cs 0 @ 20000000Hz mode 3 SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB PCI-e 0: Detected No Link. PCI-e 1: Detected No Link. USB2.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x7fedc000:0x7ff9741c BSS: 0x7ffef600 Stack: 0x7f4cbf20 Heap: 0x7f4cc000:0x7fedc000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | RGMII | 0x01 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 reading ubldr.bin ** Unable to read file ubldr.bin ** ## Starting application at 0x00200000 ... -
More info
Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | RGMII | 0x01 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> printenv bootcmd bootcmd=run setLED; run emmcboot; Marvell>> printenv emmcboot emmcboot=fatload mmc 0:1 200000 ubldr.bin; go 200000; Marvell>> Marvell>> fatls mmc 0:1 0 file(s), 0 dir(s) -
@fmotta I can’t tell you what happened but https://docs.netgate.com/pfsense/en/latest/solutions/sg-3100/reinstall-pfsense.html is probably the fastest solution.
-
@SteveITS
thanks
I think I did the right thing and ordered
netgate-installer-aarch64.img.gzShould I:
- Unzip
- 'dd' this to a thumbdrive
- Install to usb port
- power on?
-
@fmotta I have not used the (beta) installer.
https://docs.netgate.com/pfsense/en/latest/install/netinstaller.html -
@SteveITS said in SG3100 Does not boot after latest update:
https://docs.netgate.com/pfsense/en/latest/install/netinstaller.html
Hmmm seems the installer does not work for 3100
-
@fmotta said in SG3100 Does not boot after latest update:
installer does not work for 3100
Ah, I suppose that makes sense, in hindsight. Use the classic method I linked, then.
-
@SteveITS
Umm thanks?
All I need is to boot the system to get the NDI so they will send me the image so I can boot and SEE the NDII opened the case immediately. I await a response with a download link to pfSense-plus-Netgate-3100-recovery-24.03-RELEASE-armv7.img.gz
-
The NDI is on the label, the serial number (also on the label) will also identify the unit for TAC.
And, yes, there is no Net Installer for armv7. Yet.
