ATT Internet AIr

[ahole4sure]

@ahole4sure

[ahole4sure]

@flat4 did I not gray/red out anything of importance ??? did I miss something important?

[stephenw10]

Check the DNS resolver settings, that can also be set in forwarding mode. It resolves directly by default though.

Try resolving something in the pfSense GUI in Diag > DNS Lookup.
Note what servers are responding in the failed WAN state.

[ahole4sure]

@stephenw10
I will check the failed state DNS resolution (from pfsense) later today when I am back on site

But here are screenshots of the DNS Resolver. Should I just disable DNS Resolver ?

[stephenw10]

No I would expect that to work. It is in resolving mode and set to use 'all' interfaces for outgoing queries. So it should switch to use the WAN when the system default gateway changes.

[ahole4sure]

@stephenw10
So do I not have the gateway for the Internet Air established correctly - ?

Would there be any benefit for deleting the "interface" (it used to be a Suddenlink cable modem , before I added the Frontier fiber internet as WAN2)? And then recreating the interface and starting all over ??
I'm at a loss ...

[stephenw10]

Unclear at this point. You need to run some DNS testing in the failed state to ind out what's actually failing.

[ahole4sure]

@stephenw10
Ok so I got on-site

Looks like I can ping and access routes from pfsense and on the LAN
but I can NOT resolve DNS from either pFsense or the LAN

It just hangs when trying to resolve a DNS

What can I post that will help to resolve this frustrating issue ??

THANKS

[ahole4sure]

This post is deleted!

[ahole4sure]

These were attempts to ping form pfsense while in failed state - one to numerical address the other to name

[stephenw10]

So try to resolve google.com in Diag > DNS Lookup where all the configured DNS servers are tested.

[ahole4sure]

@stephenw10

So I have tried as recommended - still nothing. It's like the system gets "stuck" when I try the DNS Lookup after fail state begins. And to make matters worse the more changes I make now, it appears that coming back out of the failed state requires reboot of the pFsense to get things working for my main WAN and internet source.
I am a loss now as to how to even troubleshoot

Gonna try to call ATT today - I wish I could get a way to put ATT modem in bridge mode. As maybe mentioned before, I have DMZ set to the dhcp (later set to static) address of 192.168.2.11 that the ATT gateway/modem gave my pFsense box - yet it still shows the local IP of 192.168.1.11 in pFsense dashboard. I was hoping that it would show public IP. Not sure that it has anyhting to do with the DNS issue though.

[stephenw10]

Hmm, is it possible it's blocking or intercepting DNS traffic?

Check the state table in Diag > States when the main WAN2 is down and you are trying to resolve something. You should see the udp port 53 connections using the WAN.

Did you try changing the kill state on gateway failure setting?

[ahole4sure]

@stephenw10
So it does appear that somehting is blocking things, looking up this SYN_SENT CLOSED error

Thoughts on how to fix?

[ahole4sure]

@stephenw10
Other weird thing is that during the failed state , while on the LAN, I can bring up a google web page and sucessfully google something and it will bring up a page sucessfully

[stephenw10]

There are no DNS connections shown there.

Try setting All interfaces and filtering by: :53

Make sure there are at least some on WAN and they're not all on WAN2.

Did you try the state kill setting?

[ahole4sure]

@stephenw10
I am baout ready to pull my air out - lol
I can't get anyone that speaks english (my primary language) from ATT support and what's worse nobody that knows what "bridge mode" is.

I reverted my Internet Air back to the original factory 192.168.1.1 address
Then changed it to 192.168.1.155
That then gave my connection form the LAN of the Internet Air to the WAN configured interface of the pFsense an IP of 192.168.1.156
Setup the gateway and the gateway group

When pulled the ethernet cord on the WAN2 it goes to failed state as it should

Still NO DNS -- I have attched the STATE you mentioned filtered for 53

The crazy thing is that despite the setting the state kill setting I still have to reboot the box inorder to get internet / DNS back after the failed state is corrected

I'm at a complete loss - ugh

[stephenw10]

Ah, it looks like your LAN is also using 192.168.1.0/24?
if
That's a subnet conflict between WAN and LAN. You need to change one of those to a different /24 subnet. That obviously wouldn't be a problem if you had a public IP on WAN.

However it's also different to when you set it up above where the WAN was using the 192.168.2.0/24 subnet.

[ahole4sure]

@stephenw10
Ok I can change back to 192.168.2.0

but we were running into the same issue there as well??

Also - question -- when I create the interface connection and set up as a DHCP connection for the created WAN it seems to create some "dummy" gateway (that is greyed out and not available for use in the gateway group area). Do I just create an additional gateway ? Or how to handle that?

[stephenw10]

Change it back. Any tests with the subnets conflicting will definitely fail an just confuse matters.

We want to see DNS states on the WAN, without being NAT'd, and check if there are any reply packets.

Is your outbound NAT still set to automatic?