pfSense not enabling port

georgelza

@stephenw10 said in pfSense not enabling port:

Did you ever try just linking the two SFP+ ports directly to see if it would link up and be stable?

explain.

ok, corrected mod_probe, set to =1.
executed the reload.

below is the output, port on switch has gone red now.
wondering if it might sense to get the port and the interface to be back on auto negotiate.

G

[31585.664382] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31585.769298] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31585.873330] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31585.888669] ixgbe 0000:04:00.1: complete
[31585.889282] ixgbe 0000:04:00.0: removed PHC on enp4s0f0
[31585.949971] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left allmulticast mode
[31585.949974] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left promiscuous mode
[31586.012658] ixgbe 0000:04:00.0: complete
[31586.041780] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[31586.041782] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[31586.217345] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[31586.217650] ixgbe 0000:04:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[31586.217734] ixgbe 0000:04:00.0: MAC: 2, PHY: 19, SFP+: 5, PBA No: FFFFFF-0FF
[31586.217735] ixgbe 0000:04:00.0: a8:b8:e0:05:f0:91
[31586.218736] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[31586.234395] ixgbe 0000:04:00.0 enp4s0f0: renamed from eth0
[31587.366524] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[31587.366829] ixgbe 0000:04:00.1: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[31587.366913] ixgbe 0000:04:00.1: MAC: 2, PHY: 1, PBA No: FFFFFF-0FF
[31587.366914] ixgbe 0000:04:00.1: a8:b8:e0:05:f0:92
[31587.367921] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
[31587.378331] ixgbe 0000:04:00.1 enp4s0f1: renamed from eth0

georgelza

:(

disabled auto negotiate on interface,

did a if reload -a

dmesg results in flapping again. port on switch has gone from red to grey/no errors.

[31747.031303] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31747.135279] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31748.071313] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31748.279274] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31749.007315] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31749.111264] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31751.815311] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31751.919316] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31752.439315] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31752.543250] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31752.751293] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31752.855259] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31753.167301] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31753.271254] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31753.895300] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31753.999229] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31754.935184] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31755.039143] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31756.287172] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31756.391041] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31758.055259] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31758.159230] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31761.591166] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31761.695076] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31761.903216] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31762.007245] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31762.215038] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31762.319061] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31762.943117] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31763.047212] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31764.503186] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31764.607154] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31764.919363] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31765.023138] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31765.127138] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31765.231280] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down

georgelza

just tried something, disabled the vmbr40 bridge, by removing the physical device.

configured a ip directly onto physical device.

can't ping the 172.16.40.1 gw.

it's saying no_carrier when i do a

ip a

G

stephenw10

@georgelza said in pfSense not enabling port:

explain.

I mean just link the two SFP ports on the Topton together to see if it will link without flapping. You obviously won't be able to pass any traffic but if it shows a stable link on both ports in that situation it's probably some low level issue between the ix ports and the switch.

Though thinking more you could set that up in proxmox so you could pass traffic between them by having them on separate bridges.

georgelza

@stephenw10 will try tomorrow.

received a package bout 30min, ago, havent opened it, but think it could be the DAC cable and the 2nd Transceiver.

G

georgelza

Ran the following on the pfSense host:

 pciconf -lcv ix0

ix0@pci0:4:0:0:	class=0x020000 rev=0x01 hdr=0x00 vendor=0x8086 device=0x10fb subvendor=0xffff subdevice=0xffff
    vendor     = 'Intel Corporation'
    device     = '82599ES 10-Gigabit SFI/SFP+ Network Connection'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 3  supports D0 D3  current D0
    cap 05[50] = MSI supports 1 message, 64 bit, vector masks
    cap 11[70] = MSI-X supports 64 messages, enabled
                 Table in map 0x20[0x0], PBA in map 0x20[0x2000]
    cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS
                 max read 512
                 link x4(x8) speed 5.0(5.0) ASPM disabled(L0s)
    cap 03[e0] = VPD
    ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected
    ecap 0003[140] = Serial 1 a8b8e0ffff05ef51
    ecap 000e[150] = ARI 1
    ecap 0010[160] = SR-IOV 1 IOV disabled, Memory Space disabled, ARI disabled
                     0 VFs configured out of 64 supported
                     First VF RID Offset 0x0180, VF RID Stride 0x0002
                     VF Device ID 0x10ed
                     Page Sizes: 4096 (enabled), 8192, 65536, 262144, 1048576, 4194304

georgelza

sweeeeeet... so ye that delivery was 1 x DAC, 1 x other brand SFP+ Transciever.

plugged the DAC in between switch and pfsense SFP+ port 0
plugged the new Transceiver into pmox SFP+ port0
both started flashing...
go onto unifi network controller, both SFP+ ports immediately changed colour to hey we got something we recognise, vs grey or red.

in pmox console,

dmesg =>

[78378.314597] ixgbe 0000:04:00.0 enp4s0f0: detected SFP+: 5
[78433.681346] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX

and ip a

ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host noprefixroute
       valid_lft forever preferred_lft forever
2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
3: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:72 brd ff:ff:ff:ff:ff:ff
4: enp5s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:73 brd ff:ff:ff:ff:ff:ff
5: enp6s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:74 brd ff:ff:ff:ff:ff:ff
8: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.50/24 scope global vmbr0
       valid_lft forever preferred_lft forever
    inet6 fe80::aab8:e0ff:fe02:a371/64 scope link
       valid_lft forever preferred_lft forever
9: vmbr40: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::aab8:e0ff:fe05:f091/64 scope link
       valid_lft forever preferred_lft forever
10: tap100i0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i0 state UNKNOWN group default qlen 1000
    link/ether c6:2d:5a:7a:41:d7 brd ff:ff:ff:ff:ff:ff
11: fwbr100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
12: fwpr100p0@fwln100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 76:c4:56:d3:6a:93 brd ff:ff:ff:ff:ff:ff
13: fwln100i0@fwpr100p0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i0 state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
14: tap100i1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i1 state UNKNOWN group default qlen 1000
    link/ether 76:c9:86:22:cc:30 brd ff:ff:ff:ff:ff:ff
15: fwbr100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
16: fwpr100p1@fwln100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 26:2d:af:5a:9a:b4 brd ff:ff:ff:ff:ff:ff
17: fwln100i1@fwpr100p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i1 state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
18: tap100i2: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i2 state UNKNOWN group default qlen 1000
    link/ether c2:9f:1f:4e:c6:2e brd ff:ff:ff:ff:ff:ff
19: fwbr100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
20: fwpr100p2@fwln100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr40 state UP group default qlen 1000
    link/ether 72:43:cc:4b:b3:40 brd ff:ff:ff:ff:ff:ff
21: fwln100i2@fwpr100p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i2 state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
39: enp4s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr40 state UP group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
40: enp4s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:05:f0:92 brd ff:ff:ff:ff:ff:ff

now to reconfigure vlan40 from the igc0.40 onto ix0

ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: ens18: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:c0:e8:1e brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.51/24 metric 100 brd 172.16.10.255 scope global dynamic ens18
       valid_lft 4206sec preferred_lft 4206sec
    inet6 fe80::be24:11ff:fec0:e81e/64 scope link
       valid_lft forever preferred_lft forever
3: ens19: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:81:2c:cb brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe81:2ccb/64 scope link
       valid_lft forever preferred_lft forever
4: ens20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:1e:20:ac brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe1e:20ac/64 scope link
       valid_lft forever preferred_lft forever
5: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default
    link/ether 02:42:cb:d9:fb:26 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.1/16 brd 172.17.255.255 scope global docker0
       valid_lft forever preferred_lft forever

happiness, making progress in right direction...

i configured my pfSense console to be accessible via 2nd address on 172.16.40.1. reconfigured that via primary 172.16.10.1 interface to now be serviced/routed via ix0, then connected to console via new 2nd, working so have a back door ;)

connected via back door and went and reconfigured vlan0, vlan20, vlan30 to now be routed via ix0 also. hit refresh on my browser which access console via 172.16.10.1 and did same for 172.16.40.1, still accessible.
at this point the below picture reflect pfsense config.

Ok, this seemed good. but (once i unplugged the 2.5 igc1 cat6 cable between ProMax port24 and pfSense ) now found i could not access anything else that sat on 172.16.10.0/24 network.

At this point wondering... am i trying to get something to work and whats the value of it... does it make sense...

To fix the above I reconfigured onto this.

Maybe leave vlan0, vlan20, vlan30 and vlan100 on igc1 as all the device that connect to that themself are either wifi, 1GbE or 2.5GbE based.
then leave vlan40 on ix0 and the device that will on there is 10GbE based.
I got an aggregation on the way anyhow. so SFP+ port 2 on pfSense will go into aggregation and the pmox and TrueNAS will go into that.

some comments, view's

note, on ubuntu-01 i still dont have a ip assigned to the vlan30 and vlan40 interfaces... so thats i guess the last to be fixed...

G

georgelza

for reference, here is my pmox datacenter

and pmox1 server network configuration.

interesting enough, without telling my unifi environment, this is what it's showing.

<note the MAC addresses assigned to net1 and net2 has been dhcp reserved in pfsense on the respective vlans as 172.16.30.11 and 172.16.40.11

10Gtek 10GBase-SR SFP+ LC Transceiver, 10G 850nm Multimode SFP Moduledell emc ftlx8574d3bnl-fc

stephenw10

@georgelza said in pfSense not enabling port:

Ok, this seemed good. but (once i unplugged the 2.5 igc1 cat6 cable between ProMax port24 and pfSense ) now found i could not access anything else that sat on 172.16.10.0/24 network.

Unclear exactly what you are testing to and from in that scenario. Just disconnecting the cable won't start routing via some other subnet if it still has an IP address directly in the subnet.

georgelza

@stephenw10

I wanted all traffic between the ProMax & pfSense to flow over the DAC.

why i reconfigured all vlan GW's to then sit on the Ix0 interface.

in the end what i got is vlan0, vlan20, vlan30 and vlan100 which is "low" bandwidth traffic get to the fSense via igb1 / 2.5GbE and then all traffic from vlan40, will sit on ix0,

G

georgelza

strange bit...
on my pfSense

on ubuntu-01

ifconfig -a
docker0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 172.17.0.1  netmask 255.255.0.0  broadcast 172.17.255.255
        ether 02:42:79:4c:b3:b2  txqueuelen 0  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens18: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 172.16.10.51  netmask 255.255.255.0  broadcast 172.16.10.255
        inet6 fe80::be24:11ff:fec0:e81e  prefixlen 64  scopeid 0x20<link>
        ether bc:24:11:c0:e8:1e  txqueuelen 1000  (Ethernet)
        RX packets 30289  bytes 4984073 (4.9 MB)
        RX errors 0  dropped 32  overruns 0  frame 0
        TX packets 15485  bytes 3129562 (3.1 MB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens19: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether bc:24:11:81:2c:cb  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens20: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether bc:24:11:1e:20:ac  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 96  bytes 7756 (7.7 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 96  bytes 7756 (7.7 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

georgelza

Got the 172.16.30.11 working, did a manual configuration inside ubuntu.

battling with 172.16.40.11 thats on the fiber.

G

georgelza

figured i'd try re-install ubuntu with the interfaces now "working"
assigning the multiple networks at configuration time,

as soon as ubuntu installer started, immediately picked up the intended 172.16.10.51 and 172.16.30.11 address. 172.16.40.11 did not want to get picked.

implying i have some rule problem between pfsense and the Proxmox.
this is also the interface even when manually configuring it i could not get to access on the guestVM.

G

Ubuntu installer

georgelza

i changed the interface from a vlan to a lan... as it's not a vlan anymore.

scratching head.

G

georgelza

press enough buttons and things get working, hehehehe

;)
now to unpack a bit what is what and then update diagrams for my own understanding...

then onto next phase...

G

stephenw10

@georgelza said in pfSense not enabling port:

now to unpack a bit what is what and then update diagrams for my own understanding...

Yup, a diagram here would definitely help a lot!

georgelza

@stephenw10

Da pictures... The planning, Phase 1 is completed.

The aggregation switch is on its way so that will be phase 2 cable wise by next weekend. Planning on getting another TopTon on Black Friday. will also then get the dual port 10GbE x520 Fiber card for the TrueNAS.

935535dc-06c7-4980-b202-a8fb252e68ea-NetworkPhases 2.1-Day 1.jpg NetworkPhases 2.1-Day 1.jpg

f0ebb7ab-62b8-41c3-92cc-19107bb02ae5-NetworkPhases 2.1-Day 2.jpg NetworkPhases 2.1-Day 2.jpg

4affdc3b-7a8e-432f-abb2-9f625689ec0e-NetworkPhases 2.1-Cabling 1.0.jpg
NetworkPhases 2.1-Cabling 1.0.jpg

Gblenn

@georgelza said in pfSense not enabling port:

press enough buttons and things get working, hehehehe

;)
now to unpack a bit what is what and then update diagrams for my own understanding...

then onto next phase...

G

Glad to see that you finally got it to work... it's a great feeling!
And now you know what cables and modules to use going forward. And as you already found out, there are likely others that will work as well. I suppose you were just unlucky with the one's you had...

And who knows, there might be a solution with the Topton NIC, to make it like those DELL modules as well. I guess the thing is that since there is firmware in those modules, DAC's as well, and even though protocols are "standardized", it's still a matter of interpretation sometimes... And some vendors, like Intel, choose to "blacklist" not supported devices inside some of their cards... Hence the command you tried earlier to "allow_unsupported device".

One thought about your issue with the Docker application not "finding" VLAN 40...

You can of course add a specific VLAN tag to each interface you assign to a VM. And you don't have to set the bridge or anything to be "VLAN aware". But in this case Proxmox will Untag all traffic towards the VM and Tag it going out of the bridge towards the switch..

And since docker can only "see" what the host VM is receiving (untagged traffic), neither docker not the containers will be able to attach to any specific VLAN.

To change the bridge interface (vmbr0, vmbr40) into a trunk interface, simply make it VLAN aware from the UI.
Then it will pass any and all VLAN's from 2-4094, or something like that.

And then on the VM OS, you have to handle the VLAN's. Which I have never tried myself, but basically in docker you will have to create and interface which you can then assign to the container. Something looking like this I suppose...

docker network create -d macvlan
--subnet=192.168.40.0/24
--gateway=192.168.40.1
-o parent=eth0.40
vlan40_net

docker run -d --name mycontainername --network vlan40_net some_image

Gblenn

@georgelza said in pfSense not enabling port:

Planning on getting another TopTon on Black Friday. will also then get the dual port 10GbE x520 Fiber card for the TrueNAS.

Remember the issues you had here... so when looking for x520 cards, do some googling and perhaps you can make use of your DELL links... When I got my X520's, I had read about how Intel is picky with which modules they accept. They actually whitelists (in the firmware of the card) which modules they accept, and anything that doesn't match is an "unsupported device". So I went for a Fujitsu made Intel card and have had no trouble with it. There are plenty out there and I hear Mellanox cards are great as well.

georgelza

@Gblenn said in pfSense not enabling port:

One thought about your issue with the Docker application not "finding" VLAN 40...

this was not docker, this was purely a ubuntu vm on proxmox, trying to remember now if it auto dhcp picked up ip in the end...

i did end rebuilding the vm, thinking that maybe when i build it and the network publish internally via proxmox was not 100% it might have impacted the vm so once i knew the networks were now more "right" redid the vm.. lessons learned with how i want to manage the ip ranges etc, as i build broke down and rebuild...

ps I ALSO did end making vlan40 just lan40... as it's the only network sitting on that port on the pfsense and will have a dedicated port on the proxmox hosts.

@Gblenn said in pfSense not enabling port:

Remember the issues you had here... so when looking for x520 cards, do some googling and perhaps you can make use of your DELL links... When I got my X520's, I had read about how Intel is picky with which modules they accept. They actually whitelists (in the firmware of the card) which modules they accept, and anything that doesn't match is an "unsupported device". So I went for a Fujitsu made Intel card and have had no trouble with it. There are plenty out there and I hear Mellanox cards are great as well.

Will need to find exactly what i'm looking for before the day and then hope it's there on the day to add to basket at a black friday special price.

luckily the Dell/EMC transcievers work happily in the Unifi switches so thats at least 1/2 off. looking at the prices... I now have a known workable solution locally available... so might do the transcievers locally... also

he he he. this thread turned into a network/proxmox/pfsense rabbit hole... hope it ends being useful for others... as i've noticed allot of ppl now deploy their pfsense as a guest on proxmox... so maybe this will help them.

i'm seriously impressed with these little topton devices, packs a mean amount of power in a nicely packaged solution.
with this i5 1335 and i5 1240 being 2 very proxmox option CPU's and think the U300E being awesome as a physical pfSense host, got some serious single thread capabilities.

now to figure out how i want to do the storage... know i know to little and probable allot to make better...

G