NG6100 does not start up

[jberke]

@stephenw10 Thank you for your help! It seems m2 ports are not working neither. It boots only when no usb or m2 attached to the device. eMMC is completly burned and may have other issues we cannot find. I belive this unit is gone, so we waiot for the new one ordered yesterday. No solution for this.

[stephenw10]

Mmm, disappointing. Yes if the LED remains orange it's not POSTing. Curious that it did it one time. Not sure there anything more we can try though.

[jberke]

@stephenw10 hi, it seems I fixed the booting part. Now I am able to boot with an installer usb stick (I did it couple of times with other NG products and used an older one with the proper usb port :) )

It does not recognize eMMC and NVMe SSD neither. This is the console ouptut before I got stuck with no suitable disk error:

isSecurebootEnabled = 01
secureboot not enabled
Loading Usb Lens...
 Provider:  Insyde Software
 Version:   05.12.02.0040.0009.16
 Product:   BlinkBoot(R) Harrisonville USB Lens
 Licensee:  Silicom Ltd.
 Start:     03/20/2018
 End:       12/31/2099

Validating Signature... [Pass]

Installing Usb Lens...

Loading Nvme Lens...
 Provider:  Insyde Software
 Version:   05.12.02.0040.0009.16
 Product:   BlinkBoot(R) Harrisonville NVMe Lens
 Licensee:  Silicom Ltd.
 Start:     11/16/2020
 End:       12/31/2099

Validating Signature... [Pass]

Installing Nvme Lens...

Loading Sata Lens...
 Provider:  Insyde Software
 Version:   05.12.02.0040.0009.16
 Product:   BlinkBoot(R) Harrisonville SATA Lens
 Licensee:  Silicom Ltd.
 Start:     03/20/2018
 End:       12/31/2099

Validating Signature... [Pass]

Installing Sata Lens...

Loading SdMmc Lens...
 Provider:  Insyde Software
 Version:   05.12.02.0040.0009.16
 Product:   BlinkBoot(R) Harrisonville SDxx/eMMC Lens
 Licensee:  Silicom Ltd.
 Start:     03/20/2018
 End:       12/31/2099

Validating Signature... [Pass]

Installing SdMmc Lens...

Mapping table
      FS2: Alias(s):F0:
          Fv(E35C4A77-3D00-4337-A625-B980A9E00F6C)
      FS4: Alias(s):F0:
          Fv(F9657F27-CAE7-4951-A406-D286157B63EF)
      FS5: Alias(s):HD12c0b:;BLK1:
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,0x1041                                                8)
      FS6: Alias(s):HD12c0d:;BLK3:
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(3,MBR,0x90909090,0x232F69,0                                                x20000)
      FS3: Alias(s):F0:
          Fv(E7082AE5-3036-407A-8060-FDF027F74632)
      FS0: Alias(s):F0:
          Fv(1643501D-ABD6-4ECC-85DE-3D95D23423FE)
      FS1: Alias(s):F0:
          Fv(50E81C5A-EAB2-495C-871E-EF46044C8959)
     BLK0: Alias(s):
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)
     BLK2: Alias(s):
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(2,MBR,0x90909090,0x10419,0x                                                222B50)
Locking SPI ...
Launching Lock flash...
Already Lock the SPI
Error. 8BE4DF61-93CA-11D2-AA0D-00E098032B8C - BootNext - unable to set: Not Foun                                                d
Checking Hotkey...
Key Options:
  'r' -- Clear boot order list.
  'p' --  PXE boot.
  'F2' -- Boot Manager Menu.
 Any key to continue
Error. C450ED8E-C3C2-4FE7-AEE6-D1C50ABB78CF - PXEVariable - unable to set: Not F                                                ound
Error. C450ED8E-C3C2-4FE7-AEE6-D1C50ABB78CF - RestOrderVariable - unable to set:                                                 Not Found
Option: 00. Variable: Boot0001
  Desc    - bootx64.efi
  DevPath - PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,0x10                                                418)/\EFI\BOOT\bootx64.efi
  Optional- N
BootOrder0000:FS5:\EFI\BOOT\bootx64.efi
Option: 01. Variable: Boot0000
  Desc    - PXE-0
  DevPath - Fv(E35C4A77-3D00-4337-A625-B980A9E00F6C)/\pxe_0.nsh
  Optional- N
BootOrder0001:FS2:\pxe_0.nsh
Shell> map -r
Mapping table
      FS2: Alias(s):F0:
          Fv(E35C4A77-3D00-4337-A625-B980A9E00F6C)
      FS4: Alias(s):F0:
          Fv(F9657F27-CAE7-4951-A406-D286157B63EF)
      FS5: Alias(s):HD12c0b:;BLK1:
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,0x1041                                                8)
      FS6: Alias(s):HD12c0d:;BLK3:
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(3,MBR,0x90909090,0x232F69,0                                                x20000)
      FS3: Alias(s):F0:
          Fv(E7082AE5-3036-407A-8060-FDF027F74632)
      FS0: Alias(s):F0:
          Fv(1643501D-ABD6-4ECC-85DE-3D95D23423FE)
      FS1: Alias(s):F0:
          Fv(50E81C5A-EAB2-495C-871E-EF46044C8959)
     BLK0: Alias(s):
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)
     BLK2: Alias(s):
          PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(2,MBR,0x90909090,0x10419,0x                                                222B50)
Shell> bcfg boot dump
Option: 00. Variable: Boot0001
  Desc    - bootx64.efi
  DevPath - PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,0x10                                                418)/\EFI\BOOT\bootx64.efi
  Optional- N
BootOrder0000:FS5:\EFI\BOOT\bootx64.efi
Option: 01. Variable: Boot0000
  Desc    - PXE-0
  DevPath - Fv(E35C4A77-3D00-4337-A625-B980A9E00F6C)/\pxe_0.nsh
  Optional- N
BootOrder0001:FS2:\pxe_0.nsh
Shell> echo %BootOrder0000%
FS5:\EFI\BOOT\bootx64.efi
Shell> %BootOrder0000%
Consoles: EFI console
    Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/amd64 EFI loader, Revision 1.1
(Thu Sep 19 15:07:55 UTC 2024 root@freebsd)

   Command line arguments: FS5:\EFI\BOOT\bootx64.efi
   Image base: 0x76292000
   EFI version: 2.50
   EFI Firmware: Insyde May  3 2022 11:32:00 (rev 0.00)
   Console: efi (0x1000)
   Load Path: \EFI\BOOT\bootx64.efi
   Load Device: PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,                                                0x10418)
   BootOrder: 0001 0000
Trying ESP: PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(1,MBR,0x90909090,0x1,0x10                                                418)
Setting currdev to disk0p1:
Trying: PciRoot(0x0)/Pci(0x15,0x0)/USB(0x2,0x0)/HD(2,MBR,0x90909090,0x10419,0x22                                                2B50)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.lua
Netgate Cordoba System detected.
Loading /boot/loader.conf.local


Loading kernel...
/boot/kernel/kernel text=0x1a4c80 text=0xff1068 text=0x17ed3a0 data=0x180+0xe80 data=0x24b7c8+0x3b4838 0x8+0x1d3940+0x8+0x1e8eda-
Loading configured modules...
can't find '/boot/entropy'
can't find '/etc/hostid'
staging 0x6a200000-0x6e0d8000 (not copying) tramp 0x6e0d8000 PT4 0x6e0d9000
Start @ 0xffffffff803a5000 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
---<<BOOT>>---
Copyright (c) 1992-2024 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 15.0-CURRENT #0 installer-RELENG_v1_0-n256387-33bc50df25b: Thu Sep 19 15:09:47 UTC 2024
    root@freebsd:/var/jenkins/workspace/pfSense-installer-snapshots-v1_0-main/obj/amd64/S5t4JeUd/var/jenkins/workspace/pfSense-installer-snapshots-v1_0-main/sources/FreeBSD-src-installer-RELENG_v1_0/amd64.amd64/sys/pfSense-Installer amd64
FreeBSD clang version 18.1.6 (https://github.com/llvm/llvm-project.git llvmorg-18.1.6-0-g1118c2e05e67)
VT(vga): resolution 640x480
CPU: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz (2200.21-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506f1  Family=0x6  Model=0x5f  Stepping=1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2294e283<FSGSBASE,TSCADJ,SMEP,ERMS,NFPUSG,MPX,PQE,RDSEED,SMAP,CLFLUSHOPT,PROCTRACE,SHA>
  Structured Extended Features3=0xac000400<MD_CLEAR,IBPB,STIBP,ARCH_CAP,SSBD>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  IA32_ARCH_CAPS=0xc69<RDCL_NO,SKIP_L1DFL_VME,MDS_NO>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
  TSC: P-state invariant, performance statistics
real memory  = 8589934592 (8192 MB)
avail memory = 8145465344 (7768 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <INSYDE H2O BIOS>
WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
ioapic0 <Version 2.0> irqs 0-119
Launching APs: 3 1 2
TCP_ratelimit: Is now initialized
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff807524f0, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff807525a0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80752650, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80772100, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff807721b0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80772260, 0) error 1
random: entropy device external interface
wlan: mac acl policy registered
kbd0 at kbdmux0
WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 15.0.
efirtc0: <EFI Realtime Clock>
efirtc0: registered as a time-of-day clock, resolution 1.000000s
netgate0: <Netgate 6100>
vtvga0: <VT VGA driver>
smbios0: <System Management BIOS> at iomem 0x7c51b000-0x7c51b017
smbios0: Version: 3.0
acpi0: <INSYDE H2O BIOS>
acpi0: Power Button (fixed)
unknown: I/O range not supported
cpu0: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 24000000 Hz quality 950
Event timer "HPET" frequency 24000000 Hz quality 550
Event timer "HPET1" frequency 24000000 Hz quality 440
Event timer "HPET2" frequency 24000000 Hz quality 440
Event timer "HPET3" frequency 24000000 Hz quality 440
Event timer "HPET4" frequency 24000000 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <processor> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> mem 0x81500000-0x8151ffff at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> mem 0x81520000-0x8153ffff at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> mem 0x81540000-0x8155ffff at device 12.0 on pci0
pci4: <ACPI PCI bus> on pcib4
igc0: <Intel(R) Ethernet Controller I225-V> mem 0x81300000-0x813fffff,0x81400000-0x81403fff at device 0.0 on pci4
igc0: Using 1024 TX descriptors and 1024 RX descriptors
igc0: Using 4 RX queues 4 TX queues
igc0: Using MSI-X interrupts with 5 vectors
igc0: Ethernet address: 90:ec::32
igc0: netmap queues/slots: TX 4/1024, RX 4/1024
pcib5: <ACPI PCI-PCI bridge> mem 0x81560000-0x8157ffff at device 14.0 on pci0
pci5: <ACPI PCI bus> on pcib5
igc1: <Intel(R) Ethernet Controller I225-V> mem 0x81100000-0x811fffff,0x81200000-0x81203fff at device 0.0 on pci5
igc1: Using 1024 TX descriptors and 1024 RX descriptors
igc1: Using 4 RX queues 4 TX queues
igc1: Using MSI-X interrupts with 5 vectors
igc1: Ethernet address: 90:ec::33
igc1: netmap queues/slots: TX 4/1024, RX 4/1024
pcib6: <ACPI PCI-PCI bridge> mem 0x81580000-0x8159ffff at device 15.0 on pci0
pci6: <ACPI PCI bus> on pcib6
igc2: <Intel(R) Ethernet Controller I225-V> mem 0x80f00000-0x80ffffff,0x81000000-0x81003fff at device 0.0 on pci6
igc2: Using 1024 TX descriptors and 1024 RX descriptors
igc2: Using 4 RX queues 4 TX queues
igc2: Using MSI-X interrupts with 5 vectors
igc2: Ethernet address: 90:ec::34
igc2: netmap queues/slots: TX 4/1024, RX 4/1024
pcib7: <ACPI PCI-PCI bridge> mem 0x815a0000-0x815bffff at device 16.0 on pci0
pci7: <ACPI PCI bus> on pcib7
igc3: <Intel(R) Ethernet Controller I225-V> mem 0x80d00000-0x80dfffff,0x80e00000-0x80e03fff at device 0.0 on pci7
igc3: Using 1024 TX descriptors and 1024 RX descriptors
igc3: Using 4 RX queues 4 TX queues
igc3: Using MSI-X interrupts with 5 vectors
igc3: Ethernet address: 90:ec:
igc3: netmap queues/slots: TX 4/1024, RX 4/1024
pcib8: <ACPI PCI-PCI bridge> mem 0x815c0000-0x815dffff at device 17.0 on pci0
pci8: <ACPI PCI bus> on pcib8
xhci0: <Intel Denverton USB 3.0 controller> mem 0x815e0000-0x815effff at device 21.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pcib9: <ACPI PCI-PCI bridge> at device 22.0 on pci0
pci9: <ACPI PCI bus> on pcib9
ix0: <Intel(R) X553 N (SFP+)> mem 0x80400000-0x805fffff,0x80604000-0x80607fff at device 0.0 on pci9
ix0: Using 2048 TX descriptors and 2048 RX descriptors
ix0: Using 4 RX queues 4 TX queues
ix0: Using MSI-X interrupts with 5 vectors
ix0: allocated for 4 queues
ix0: allocated for 4 rx queues
ix0: Ethernet address: 90:ec:
ix0: eTrack 0x8000084b PHY FW V65535
ix0: netmap queues/slots: TX 4/2048, RX 4/2048
ix1: <Intel(R) X553 N (SFP+)> mem 0x80200000-0x803fffff,0x80600000-0x80603fff at device 0.1 on pci9
ix1: Using 2048 TX descriptors and 2048 RX descriptors
ix1: Using 4 RX queues 4 TX queues
ix1: Using MSI-X interrupts with 5 vectors
ix1: allocated for 4 queues
ix1: allocated for 4 rx queues
ix1: Ethernet address: 90:ec::31
ix1: eTrack 0x8000084b PHY FW V65535
ix1: netmap queues/slots: TX 4/2048, RX 4/2048
pcib10: <ACPI PCI-PCI bridge> at device 23.0 on pci0
pci10: <ACPI PCI bus> on pcib10
ix2: <Intel(R) X553 L (1GbE)> mem 0x80a00000-0x80bfffff,0x80c04000-0x80c07fff at device 0.0 on pci10
ix2: Using 2048 TX descriptors and 2048 RX descriptors
ix2: Using 4 RX queues 4 TX queues
ix2: Using MSI-X interrupts with 5 vectors
ix2: allocated for 4 queues
ix2: allocated for 4 rx queues
ix2: Ethernet address: 90:ec::2f
ix2: eTrack 0x80000889
ix2: netmap queues/slots: TX 4/2048, RX 4/2048
ix3: <Intel(R) X553 L (1GbE)> mem 0x80800000-0x809fffff,0x80c00000-0x80c03fff at device 0.1 on pci10
ix3: Using 2048 TX descriptors and 2048 RX descriptors
ix3: Using 4 RX queues 4 TX queues
ix3: Using MSI-X interrupts with 5 vectors
ix3: allocated for 4 queues
ix3: allocated for 4 rx queues
ix3: Ethernet address: 90:ec::2e
ix3: eTrack 0x80000889
ix3: netmap queues/slots: TX 4/2048, RX 4/2048
pci0: <simple comms> at device 24.0 (no driver attached)
sdhci_pci0: <Intel Denverton eMMC 5.0 Controller> mem 0x815f6000-0x815f6fff,0x815f7000-0x815f7fff at device 28.0 on pci0
sdhci_pci0: 1 slot(s) allocated
mmc0: <MMC/SD bus> on sdhci_pci0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <memory> at device 31.2 (no driver attached)
pci0: <serial bus> at device 31.5 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
ns8250: UART FCR is broken0 class UART with FIFOs> port 0x3f8-0x3ff irq 16 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
uart1: <Non-standard ns8250 class UART with FIFOs> port 0x2f8-0x2ff irq 17 on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
Timecounter "TSC-low" frequency 1100000029 Hz quality 1000
Timecounters tick every 1.000 msec
ugen0.1: <Intel XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
random: unblocking device.
uhub0: 8 ports with 8 removable, self powered
ugen0.2: <Verbatim STORE N GO> at usbus0
umass0 on uhub0
umass0: <Verbatim STORE N GO, class 0/0, rev 2.00/1.00, addr 1> on usbus0
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <Verbatim STORE N GO 1.00> Removable Direct Access SCSI-2 device
da0: Serial Number C34
da0: 40.000MB/s transfers
da0: 3824MB (7831552 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
Trying to mount root from ufs:/dev/ufs/pfSense_Install [ro,noatime]...
No suitable dump device was found.
Starting file system checks:
/dev/ufs/pfSense_Install: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ufs/pfSense_Install: clean, 30340 free (12 frags, 3791 blocks, 0.0% fragmentation)
Mounting local filesystems:.
hw.bus.devctl_nomatch_enabled: 1 -> 1
Autoloading module: ichsmb
ichsmb0: <Intel Denverton SMBus controller> port 0x2000-0x201f mem 0x815f8000-0x815f80ff at device 31.4 on pci0
smbus0: <System Management Bus> on ichsmb0
Setting up harvesting: PURE_RDRAND,[CALLOUT],[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
Setting hostname: pfSense-install.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg
32-bit compatibility ldconfig path:
lo0: link state changed to UP
Starting Network: lo0 igc0 igc1 igc2 igc3 ix0 ix1 ix2 ix3 enc0.
lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
        options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0xa
        groups: lo
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igc0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igc1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igc2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igc3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ix0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ix1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::31
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ix2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::2f
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ix3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::2e
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0 metric 0 mtu 1536
        options=0
        groups: enc
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting devd.
Starting Network: igc0.
igc0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::32
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: igc1.
igc1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::33
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: igc2.
igc2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::34
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: igc3.
igc3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e427bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: ix0.
ix0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec:
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: ix1.
ix1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::31
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: ix2.
ix2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::2f
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: ix3.
ix3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
        ether 90:ec::2e
        media: Ethernet autoselect
        status: no carrier
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting Network: enc0.
enc0: flags=0 metric 0 mtu 1536
        options=0
        groups: enc
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
route: message indicates error: File exists
add host 127.0.0.1: gateway lo0 fib 0: route already in table
Additional inet routing options: gateway=YES.
route: message indicates error: File exists
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Updating /var/run/os-release done.
Creating and/or trimming log files.
Clearing /tmp (X related).
Starting syslogd.
Starting local daemons:/dev/md3: 8.0MB (16384 sectors) block size 32768, fragment size 4096
        using 4 cylinder groups of 2.03MB, 65 blks, 384 inodes.
        with soft updates
super-block backups (for fsck_ffs -b #) at:
 192, 4352, 8512, 12672
Creating the certificate key...
Creating the nginx self-signed certificate...
.
Mounting late filesystems:.
nextboot: unlink /boot/nextboot.conf: Read-only file system
Performing sanity check on nginx configuration:
Netgate Cordoba GPIO Driver 0.4 loaded
cordbuc0: <Netgate Cordoba IO controller> at port 0x800 on isa0
gpio0: <Cordoba uC GPIO controller> on cordbuc0
gpiobus0: <GPIO bus> on gpio0
gpioled0: <GPIO led> at pin 0 on gpiobus0
gpioled1: <GPIO led> at pin 1 on gpiobus0
gpioled10: <GPIO led> at pin 10 on gpiobus0
gpioled11: <GPIO led> at pin 11 on gpiobus0
gpioled2: <GPIO led> at pin 2 on gpiobus0
gpioled3: <GPIO led> at pin 3 on gpiobus0
gpioled4: <GPIO led> at pin 4 on gpiobus0
gpioled5: <GPIO led> at pin 5 on gpiobus0
gpioled6: <GPIO led> at pin 6 on gpiobus0
gpioled7: <GPIO led> at pin 7 on gpiobus0
gpioled8: <GPIO led> at pin 8 on gpiobus0
gpioled9: <GPIO led> at pin 9 on gpiobus0
gpioc0: <GPIO controller> on gpio0
nginx: the configuration file /usr/local/etc/nginx/nginx.conf syntax is ok
nginx: configuration file /usr/local/etc/nginx/nginx.conf test is successful
Starting nginx.
Generating RSA host key.
3072 SHA256: root@pfSense-install (RSA)
Generating ECDSA host key.
256 SHA256:VJe+ root@pfSense-install (ECDSA)
Generating ED25519 host key.
256 SHA256: root@pfSense-install (ED25519)
Performing sanity check on sshd configuration.
Starting sshd.
Starting cron.

[stephenw10]

Hmm, what NVMe drive are you using?

What did you do to allow it to start booting USB?

[jberke]

@stephenw10 Hi, I used a very old USB2 stick and that worked only on the lower USB port only. Its size was 4GB only because all other/larger drives, including USB3 sticks were not working.
Regarding the NVMe drive, it is a Western Digital one, but turned out it is not good even it is a B+M key M2 drive. I am looking for another drive, but it is nearly impossible to buy, I checked lots of places. I am happy to buy from Netgate too, but there is no any in the shop.
Also I identified the leds meaning (at least the pattern which are for reset, normal boot, restart, on/off state) on the PCBA and that helped me to boot the unit again.
Thanks,
János

[stephenw10]

Do you have the actual model number of that SSD? Good to know what drives are not recognised.

[jberke]

@stephenw10 it was a WD Red SA500 500GB M.2 however it is not NVMe but SATA. I identified when I checked my colleague whom I asked to buy one :) at least B+M key drive :D
To be honest, it is not easy to get the proper drive.

[stephenw10]

Ah, yes it must be NVMe. m.2 SATA is not supported there.

[mal]

I have a 6100 and I am in the same boat. I added a new certificate and then the unit stopped responding. I went on site and saw the same thing: solid orange light. Plugging in a console cable, I see nothing and no amount of holding reset/power changes anything. I did pop the button cell, but still nothing. I did put in an NVME B/M drive (KingSpec M.2 NVMe SSD NE 2242) to see if maybe the onboard MMC was dead but I still get the same symptoms. I am seeing the same four green LEDs as well.

[andrew_cb]

@mal Your symptoms sound like the eMMC has failed in a way that is preventing your 6100 from POSTing.

There are several reports of users with the same issue that have desoldered the eMMC chips and then their 4100/6100 worked afterwards.

https://forum.netgate.com/topic/196028/6100-failed-emmc-replaced-with-nvme-but-now-no-longer-reboots/21

If your 6100 is out of warranty then you have nothing to lose by attempting to desolder the eMMC chips.

[andrew_cb]

@mal Does your 6100 have the same light behavior as this (4100)?

Pressing and holding the power button appears to attempt to do something after about ten seconds (it was non responsive with a five second push) according to the eight diagnostic led's changing on the circuit board but still no output on the console, no activity on the USB key and the orange circle of death remains. In this post power button pushed for 12 second state the lit led's on the board are:
FLASH (immediately above RESET)
V3P3A

In its steady state after applying power or after pressing the power button after the above press and hold the following led's on the board are lit:
PWRGD
PWRGD
PWRGD
V3P3A

https://forum.netgate.com/topic/173106/netgate-4100-circle-shows-red-led/16