Port Forwarding stopped working after upgrading to 2.8.0
-
Upgrading pfSense wouldn't break any NAT setup.
What did break your NAT is most probably : what was your pfSense WAN IP before you've upgraded ?
And after ? If your WAN IP is "RFC 1918" then don't look any further : you have to change the NAT rule in the up stream, probably ISP router.Next step : every NAT rule has a WAN firewall rule - as traffic has to able to get into the WAN interface.
Here are mine :
Observe the States column. When traffic start to enter, the Sates counter start to go up.
If they stay at 0/0 then you'll know the traffic never reaches the pfSense WAN interface, so the issue is upstream.Anyway : https://docs.netgate.com/pfsense/en/latest/troubleshooting/nat-port-forwards.html is the check list to follow.
-
@Gertjan
ah ok for me my WAN is PPPOE and i use a login and password and then get a dynamic ip
not sure how that RFC 1918 i remember seeing that and doing it for something in the pastill check i did find out apparently my websites were working but the way i was testing is aysemetical which not sure what that means or what not
but i did find another issues i not sure if its my network card or what not
i got a 10Gtek Dual 1.25GB nic supposed to be intel as i wanted to be compatible with pfsensebut ive been experiencing since i upgraded to 2.8.0 that there so i not sure if 10Gtek company if its compatible with pfsense or not
as networking works.. and then at random times it will work partially say accessing the pfsense page you can access the page login but thats it or you loose connection.. and then might come back.. Vlans come and then they go with my cameras.. but once you reboot pfsense it works totally again.... its weird had no issues with 2..7.2 so i not sure if its a glitch bad upgrade or card that is slowly faulting but this randomise is also randomly how long between issues before was like ever 15 min to an hour to like a day or 2
-
That's not a NIC issue, you'd see everything fail if it was. Sounds more like a routing issue or possible something stalling out PHP.
Check the system logs covering the time it happened.
-
@stephenw10
sorry delay wasnt around
so what do i check from the system logs? i also gotten this error now a few times but when you try to view it it doesnt work,,, and it worked oncebut what i found is say my security cameras on 192.168.10.0 network the shinobi can see the camera but my desktop pc using the reolink on the 192.168.0.0 it looses the cameras in the reolink camera like when you typically reboot pfsense...
and then it comes back or if not i reboot pfsense and then its working again.. is that all routing issues?so when i go into system logs what am i looking for? what should i scan... and here is the error i get a few times now
would these errors be caused by a routing error? this stuff only been happening after i upgraded to 2.8.0 is there like an extra check box that might been checked after the upgrade ? that i need to toggle off etc.. but ya what do i look for in the system logs specificlly to my desktop pc
i also find if my internet stalls out it stalls out my vpn and my internet will still basiclly work on the WAN side but vpn doesnt i need to reboot pfsense to get internet on vpn side to work again its like it stalls out and then rebooting pfsense solves it... as i can ping like 1.1.1.1 but i cant ping google.ca unless i reboot pfsense but if i ping google.ca on the pfsense box then i can typically ping google.. but not to the desktop
is that also related to routing issue you think i might have
-
Mmm, if you can hit the login page but nothing beyond it that's almost always PHP stalling or being killed. That is usually a symptom of something else trying to make it do something it shouldn't or can't.
So I would be looking at the main system log leading up the failure to see what might be happening to load up PHP.
-
@stephenw10
ya so like majority of the time it will just sit there you cant click the crash reporter link i had that open and i rebooted the pfsense and i was able to click that page later the crash reporter shows nothingoh and i remember i also have issues
from the desktop pc
i not able to ssh into the pfsense or when the gui page like stalls out i can ssh in and reboot or sometimes i cant and i use a wifi plug on the pfsense to reboot.. also i noticed sometimes when i reboot normal of pfsense it never comes back up i dont currently have a monitor hooked to it.. but to get it to boot back up i toggle the wifi plug and then it boots back up again.. as after a normal reboot and it doesnt come back up within 5 min is an issuenow another thing i remember is if i cant ssh into the pfsense box from my desktop.. i can terminal into my Unraid Server and i can ssh to the pfsense fine.. and if i ssh from the desktop when its not working it will work again after a certain amount of time it just starts working
now i googled what the minum specs for pfsense 2.8.0 and saying needs a quad core with 2ghz.. now my cpu is a Intel(R) Celeron(R) J4105 CPU @ 1.50GHz 4 Core i was thinking of just upgrading my server and give my pfsense my AMD Ryzen 7 5800X 8-Core with an asus tuf x570 motherboard
as you mentioned the php is stalling out if its underpowered now from the upgradei did try a re upgrade of pfsense using hte config file but that didnt help..
so what kills or stalls the php is that happening on the desktop or is that happening on the pfsense of a combination of both..
so when i looking in the system log i dont have a php sub tab so how do i look for the php or what am i exactly looking for as i not 100% sure what to look
and do i do anything under the states or routes under the diagnostic page
is there like a diagnostic tool to test the pfsense also? and if the windows 11 desktop php stalling out how do i go about that too..
all i know is if i do a pfsense reboot it solves the problem for a while but the issues can re occur after an hour or several hours or a day or 2.. so its not specific set
-
Hmm, SSH should still work even if PHP is not responding so that could also just be a symptom.
But after you reboot and regain access to the firewall the system logs should contain some reference to what was happening at the time.
Are you able to connect to the firewall console directly when this is happening?
If there's an issue with the boot drive it might present like this is be unable to log anything. The console would be full of errors though if that happened.
-
ill have to get a monitor on the computer then so i can check when it fails to boot.. does pfsense able to show any like s.m.a.r.t errors if there is any so you can see if there is a problem? and can i run a like ssh shell command to run a diagnostic on the ssd to see if there is an error does pfsense offer that?
as for if i can connect to the firewall directly when its glitching... as of the ssh its been a mix so sometimes yes or sometimes no and it takes a bit before it allows me to ssh in it just sits at trying to connect for a long time it will either drop out after so long and you try again sometimes works next sometimes no... and sometimes it will ssh like for a minute before it prompts the login and i do
ssh admin@192.168.0.1now in the system logs whjere would i look for errors but wouldnt the errors be gone once you reboot it.. it just starts off fresh? or does it keep logs prior to the reboot..
-
i just seen a s.m.a.r.t under diagnostics my bad dislexia missed it... ill do those tests and report back too
-
so i ran the test and the results are
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU650 Serial Number: 2I3620089130 LU WWN Device Id: 0 000000 000000000 Firmware Version: V8X01c45 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 14 13:58:32 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 3) minutes. Extended self-test routine recommended polling time: ( 11) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 54346 12 Power_Cycle_Count -O--CK 100 100 000 - 199 161 Valid_Spare_Block_Cnt -O--CK 100 100 000 - 33 162 Cache_Block_Count -O--CK 100 100 000 - 706277 163 Initial_Bad_Block_Count -O--CK 100 100 000 - 100 164 Total_Erase_Count -O--CK 100 100 000 - 1509 166 Min_Erase_Count -O--CK 100 100 000 - 132 167 Average_Erase_Count -O--CK 100 100 050 - 0 168 Max_Erase_Count_of_Spec -O--CK 100 100 000 - 0 169 Remaining_Lifetime_Perc -O--CK 100 100 000 - 100 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 143 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 733685 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 61 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 1279 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 1572 232 Available_Reservd_Space -O--CK 100 100 000 - 88 241 Host_Writes_32MiB -O--CK 100 100 000 - 30179 242 Host_Reads_32MiB -O--CK 100 100 000 - 947 249 Unkn_SiliconMotion_Attr -O--CK 100 100 000 - 30444 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 36707 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/36 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2025-07-14 11:51 ? - ... ..(124 skipped). .. - 127 2025-07-14 13:56 ? - 0 2025-07-14 13:57 36 ***************** 1 2025-07-14 13:58 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 199 --- Lifetime Power-On Resets 0x01 0x010 4 54346 --- Power-on Hours 0x01 0x018 6 63292007565 --- Logical Sectors Written 0x01 0x020 6 2112800956 --- Number of Write Commands 0x01 0x028 6 1987291263 --- Logical Sectors Read 0x01 0x030 6 12572061 --- Number of Read Commands 0x01 0x038 6 195639257085 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 53 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3842 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 31 Device-to-host register FISes sent due to a COMRESETthe 2nd option logs
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Error Log Version: 1 No Errors LoggedOffline Test
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART off-line routine immediately in off-line mode". Drive command "Execute SMART off-line routine immediately in off-line mode" successful. Testing has begun. Please wait 1 seconds for test to complete. Test will complete after Mon Jul 14 14:00:32 2025 EDT Use smartctl -X to abort test. and then i did the summary smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU650 Serial Number: 2I3620089130 LU WWN Device Id: 0 000000 000000000 Firmware Version: V8X01c45 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 14 14:02:02 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 3) minutes. Extended self-test routine recommended polling time: ( 11) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 54347 12 Power_Cycle_Count -O--CK 100 100 000 - 199 161 Valid_Spare_Block_Cnt -O--CK 100 100 000 - 33 162 Cache_Block_Count -O--CK 100 100 000 - 706277 163 Initial_Bad_Block_Count -O--CK 100 100 000 - 100 164 Total_Erase_Count -O--CK 100 100 000 - 1509 166 Min_Erase_Count -O--CK 100 100 000 - 132 167 Average_Erase_Count -O--CK 100 100 050 - 0 168 Max_Erase_Count_of_Spec -O--CK 100 100 000 - 0 169 Remaining_Lifetime_Perc -O--CK 100 100 000 - 100 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 143 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 733685 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 61 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 1279 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 1572 232 Available_Reservd_Space -O--CK 100 100 000 - 88 241 Host_Writes_32MiB -O--CK 100 100 000 - 30180 242 Host_Reads_32MiB -O--CK 100 100 000 - 947 249 Unkn_SiliconMotion_Attr -O--CK 100 100 000 - 30444 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 36707 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/37 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (2) Index Estimated Time Temperature Celsius 3 2025-07-14 11:55 ? - ... ..(123 skipped). .. - 127 2025-07-14 13:59 ? - 0 2025-07-14 14:00 36 ***************** 1 2025-07-14 14:01 ? - 2 2025-07-14 14:02 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 199 --- Lifetime Power-On Resets 0x01 0x010 4 54347 --- Power-on Hours 0x01 0x018 6 63292109227 --- Logical Sectors Written 0x01 0x020 6 2112803922 --- Number of Write Commands 0x01 0x028 6 1987291287 --- Logical Sectors Read 0x01 0x030 6 12572064 --- Number of Read Commands 0x01 0x038 6 195639257085 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 53 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3842 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 31 Device-to-host register FISes sent due to a COMRESETso i ran the 4 tests
offline
short
extended
convenyanceconvenyance failed
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Conveyance Self-test functions not supported Sending command: "Execute SMART Conveyance self-test routine immediately in off-line mode". Command "Execute SMART Conveyance self-test routine immediately in off-line mode" failed: Input/output errorthe other three passed
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 54347 - # 2 Short offline Completed without error 00% 54347 - # 3 Short offline Completed without error 00% 54347and the full summary is after running those 4 tests
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU650 Serial Number: 2I3620089130 LU WWN Device Id: 0 000000 000000000 Firmware Version: V8X01c45 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 14 14:29:04 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 3) minutes. Extended self-test routine recommended polling time: ( 11) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 54347 12 Power_Cycle_Count -O--CK 100 100 000 - 199 161 Valid_Spare_Block_Cnt -O--CK 100 100 000 - 33 162 Cache_Block_Count -O--CK 100 100 000 - 706277 163 Initial_Bad_Block_Count -O--CK 100 100 000 - 100 164 Total_Erase_Count -O--CK 100 100 000 - 1509 166 Min_Erase_Count -O--CK 100 100 000 - 132 167 Average_Erase_Count -O--CK 100 100 050 - 0 168 Max_Erase_Count_of_Spec -O--CK 100 100 000 - 0 169 Remaining_Lifetime_Perc -O--CK 100 100 000 - 100 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 143 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 733685 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 62 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 1279 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 1572 232 Available_Reservd_Space -O--CK 100 100 000 - 88 241 Host_Writes_32MiB -O--CK 100 100 000 - 30180 242 Host_Reads_32MiB -O--CK 100 100 000 - 947 249 Unkn_SiliconMotion_Attr -O--CK 100 100 000 - 30444 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 36707 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 54347 - # 2 Short offline Completed without error 00% 54347 - # 3 Short offline Completed without error 00% 54347 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/39 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (4) Index Estimated Time Temperature Celsius 5 2025-07-14 12:22 ? - ... ..(121 skipped). .. - 127 2025-07-14 14:24 ? - 0 2025-07-14 14:25 36 ***************** 1 2025-07-14 14:26 ? - 2 2025-07-14 14:27 ? - 3 2025-07-14 14:28 ? - 4 2025-07-14 14:29 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 199 --- Lifetime Power-On Resets 0x01 0x010 4 54347 --- Power-on Hours 0x01 0x018 6 63292814528 --- Logical Sectors Written 0x01 0x020 6 2112820776 --- Number of Write Commands 0x01 0x028 6 1987291311 --- Logical Sectors Read 0x01 0x030 6 12572067 --- Number of Read Commands 0x01 0x038 6 195650130499 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 53 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3842 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 31 Device-to-host register FISes sent due to a COMRESETso dunno if it helps anything for boot up it showed 0 errors and such on when it struggles to reboot
-
Mmm, that seems fine.
So I'd look at the logs for the time. Including if there is a suspicious gap in the logs at that point.
-
@stephenw10
ah ok
so in the logs id just look for a gap in time then and i guess any of the sub headings... ill keep an eye out when it happens and report back ..is my current cpu under powered would that be an issue.. and ill hook up a monitor tonight so i can see any console issues especcially when it fails to reboot
does the system logs show stuff prior to a reboot when i reboot .. like does it save or is it all reset at the reboot..
and its definitely not the 10gtek card? as i know i switched to it as you guys on here mentioned dont use the realtek cards not supported..
always something lol but ill keep an eye out when it happens again
-
I would normally expect to see the logs continue and be filled with restarting processes or errors or similar. But a gap in the logs entirely would also be a clue since it implies it either could not log or logs were lost if you're running ram disks for example.
-
@stephenw10
i dont think i running a ram disk i guess thats like a c drive or d drive but in ram?so i was looking at the logs and my desktop is slugish and it cant work homedepot website right it only partially loads websites or it will give me error that something went wrong... can that also be the pfsense acting up giving me issues? i also have a my vpn fail over issue or so could it be causing trouble? i have a vpn fail over i have one for canada 1 for usa but i disabled the one because everytime i try to do something in canada i get this stupid geo location garbage so i disabled the usa one.. as if i just run canada its fine for certain things if i have usa and canada then it gives me issues with geo location...
but here is the logs anyways
and i still have a 3mbs internet connction where i live they still burry lines for rural country folks and maybe by end of year i can get 1gb which i guess is like 1000 or 8000mbsbut can you see in the logs its just acting like crap
and do you think the current comp i have even though below the minium i googled is still ok?Community Edition System Interfaces Firewall Services VPN Status Diagnostics Help StatusSystem LogsSystemGeneral System Firewall DHCP Authentication IPsec PPP PPPoE/L2TP Server OpenVPN NTP Packages Settings General Gateways Routing DNS Resolver Wireless GUI Service OS Boot Last 500 General Log Entries. (Maximum 500) Jul 14 18:55:58 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:55:58 check_reload_status 481 Reloading filter Jul 14 18:55:58 rc.gateway_alarm 30598 >>> Gateway alarm: PIA_TORONTO_VPNV4 (Addr:1.1.1.1 Alarm:0 RTT:53.723ms RTTsd:19.268ms Loss:16%) Jul 14 18:55:58 check_reload_status 481 updating dyndns PIA_TORONTO_VPNV4 Jul 14 18:55:58 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:55:58 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:55:58 check_reload_status 481 Reloading filter Jul 14 18:55:59 rc.gateway_alarm 32354 >>> Gateway alarm: WAN_PPPOE (Addr:10.11.13.49 Alarm:1 RTT:35.038ms RTTsd:28.000ms Loss:21%) Jul 14 18:55:59 check_reload_status 481 updating dyndns WAN_PPPOE Jul 14 18:55:59 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:55:59 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:55:59 check_reload_status 481 Reloading filter Jul 14 18:55:59 php-fpm 434 /rc.dyndns.update: Dynamic DNS (testserver.mine.nu) There was an error trying to determine the public IP for interface - wan (pppoe0 ). Jul 14 18:55:59 php-fpm 50460 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use WAN_PPPOE. Jul 14 18:55:59 php-fpm 66203 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PIA_TORONTO_VPNV4. Jul 14 18:56:00 php-fpm 434 /rc.dyndns.update: Dynamic DNS (trilliumjam.mine.nu) There was an error trying to determine the public IP for interface - wan (pppoe0 ). Jul 14 18:56:01 php-fpm 434 /rc.dyndns.update: phpDynDNS (mcproductions.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:56:02 php-fpm 434 /rc.dyndns.update: phpDynDNS (mikeshouse.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:56:03 php-fpm 434 /rc.dyndns.update: phpDynDNS (daddyshouse.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:56:04 php-fpm 434 /rc.dyndns.update: phpDynDNS (sierrasmiles.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:56:05 php-fpm 434 /rc.dyndns.update: Dynamic DNS (rocketchat.mine.nu) There was an error trying to determine the public IP for interface - wan (pppoe0 ). Jul 14 18:56:06 php-fpm 434 /rc.dyndns.update: Dynamic DNS () There was an error trying to determine the public IP for interface - wan (pppoe0 ). Jul 14 18:56:07 php-fpm 434 /rc.dyndns.update: Dynamic DNS (daddykins.mine.nu) There was an error trying to determine the public IP for interface - wan (pppoe0 ). Jul 14 18:56:23 rc.gateway_alarm 93983 >>> Gateway alarm: PIA_TORONTO_VPNV4 (Addr:1.1.1.1 Alarm:1 RTT:53.163ms RTTsd:20.127ms Loss:21%) Jul 14 18:56:23 check_reload_status 481 updating dyndns PIA_TORONTO_VPNV4 Jul 14 18:56:23 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:56:23 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:56:23 check_reload_status 481 Reloading filter Jul 14 18:56:24 php-fpm 50460 /rc.dyndns.update: MONITOR: PIA_TORONTO_VPNV4 has packet loss, omitting from routing group VPN_FAIL_OVER Jul 14 18:56:24 php-fpm 50460 1.1.1.1|10.25.112.45|PIA_TORONTO_VPNV4|53.369ms|20.131ms|21%|down|highloss Jul 14 18:56:24 php-fpm 50460 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 50460 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: Omitting gateway from filter ruleset. Group: "VPN_FAIL_OVER" Gateway: "PIA_TORONTO_VPNV4" IP: "10.25.112.1" Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 22748 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PIA_TORONTO_VPNV4. Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:24 php-fpm 434 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:56 rc.gateway_alarm 56498 >>> Gateway alarm: WAN_PPPOE (Addr:10.11.13.49 Alarm:0 RTT:47.490ms RTTsd:47.482ms Loss:17%) Jul 14 18:56:56 check_reload_status 481 updating dyndns WAN_PPPOE Jul 14 18:56:56 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:56:56 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:56:56 check_reload_status 481 Reloading filter Jul 14 18:56:58 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 26010 /rc.dyndns.update: phpDynDNS (testserver.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: Omitting gateway from filter ruleset. Group: "VPN_FAIL_OVER" Gateway: "PIA_TORONTO_VPNV4" IP: "10.25.112.1" Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 434 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use WAN_PPPOE. Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:58 php-fpm 38292 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:59 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:59 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:59 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:56:59 php-fpm 26010 /rc.dyndns.update: phpDynDNS (trilliumjam.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:00 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:00 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:00 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:00 php-fpm 26010 /rc.dyndns.update: phpDynDNS (mcproductions.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:01 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:01 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:01 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:01 php-fpm 26010 /rc.dyndns.update: phpDynDNS (mikeshouse.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:02 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:02 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:02 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:02 php-fpm 26010 /rc.dyndns.update: phpDynDNS (daddyshouse.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:03 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:03 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:03 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:03 php-fpm 26010 /rc.dyndns.update: phpDynDNS (sierrasmiles.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:04 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:04 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:04 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:04 php-fpm 26010 /rc.dyndns.update: phpDynDNS (rocketchat.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:05 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:05 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:05 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:05 php-fpm 26010 /rc.dyndns.update: phpDynDNS (): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:57:06 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:06 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:06 php-fpm 26010 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:57:06 php-fpm 26010 /rc.dyndns.update: phpDynDNS (daddykins.mine.nu): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry. Jul 14 18:59:01 rc.gateway_alarm 3197 >>> Gateway alarm: PIA_TORONTO_VPNV4 (Addr:1.1.1.1 Alarm:0 RTT:54.534ms RTTsd:20.744ms Loss:17%) Jul 14 18:59:01 check_reload_status 481 updating dyndns PIA_TORONTO_VPNV4 Jul 14 18:59:01 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:59:01 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:59:01 check_reload_status 481 Reloading filter Jul 14 18:59:02 php-fpm 26010 /rc.dyndns.update: MONITOR: PIA_TORONTO_VPNV4 is available now, adding to routing group VPN_FAIL_OVER Jul 14 18:59:02 php-fpm 26010 1.1.1.1|10.25.112.45|PIA_TORONTO_VPNV4|54.514ms|20.649ms|18%|online|loss Jul 14 18:59:02 php-fpm 38292 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PIA_TORONTO_VPNV4. Jul 14 18:59:12 rc.gateway_alarm 46826 >>> Gateway alarm: PIA_TORONTO_VPNV4 (Addr:1.1.1.1 Alarm:1 RTT:52.162ms RTTsd:16.742ms Loss:21%) Jul 14 18:59:12 check_reload_status 481 updating dyndns PIA_TORONTO_VPNV4 Jul 14 18:59:12 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:59:12 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:59:12 check_reload_status 481 Reloading filter Jul 14 18:59:13 php-fpm 17474 /rc.dyndns.update: MONITOR: PIA_TORONTO_VPNV4 has packet loss, omitting from routing group VPN_FAIL_OVER Jul 14 18:59:13 php-fpm 17474 1.1.1.1|10.25.112.45|PIA_TORONTO_VPNV4|52.165ms|16.768ms|21%|down|highloss Jul 14 18:59:13 php-fpm 17474 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 17474 /rc.dyndns.update: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: Omitting gateway from filter ruleset. Group: "VPN_FAIL_OVER" Gateway: "PIA_TORONTO_VPNV4" IP: "10.25.112.1" Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 22748 /rc.filter_configure_sync: GATEWAYS: Group VPN_FAIL_OVER did not have any gateways up on tier 1! Jul 14 18:59:13 php-fpm 50460 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PIA_TORONTO_VPNV4. Jul 14 18:59:26 rc.gateway_alarm 71299 >>> Gateway alarm: PIA_TORONTO_VPNV4 (Addr:1.1.1.1 Alarm:0 RTT:53.458ms RTTsd:20.524ms Loss:19%) Jul 14 18:59:26 check_reload_status 481 updating dyndns PIA_TORONTO_VPNV4 Jul 14 18:59:26 check_reload_status 481 Restarting IPsec tunnels Jul 14 18:59:26 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 18:59:26 check_reload_status 481 Reloading filter Jul 14 18:59:27 php-fpm 26010 /rc.dyndns.update: MONITOR: PIA_TORONTO_VPNV4 is available now, adding to routing group VPN_FAIL_OVER Jul 14 18:59:27 php-fpm 26010 1.1.1.1|10.25.112.45|PIA_TORONTO_VPNV4|53.754ms|20.46ms|18%|online|loss Jul 14 18:59:27 php-fpm 38292 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PIA_TORONTO_VPNV4. Jul 14 19:00:00 php 57588 [pfBlockerNG] Starting cron process. Jul 14 19:00:43 php 57588 [pfBlockerNG] No changes to Firewall rules, skipping Filter Reload Jul 14 19:02:44 rc.gateway_alarm 20187 >>> Gateway alarm: WAN_PPPOE (Addr:10.11.13.49 Alarm:1 RTT:30.610ms RTTsd:13.802ms Loss:21%) Jul 14 19:02:44 check_reload_status 481 updating dyndns WAN_PPPOE Jul 14 19:02:44 check_reload_status 481 Restarting IPsec tunnels Jul 14 19:02:44 check_reload_status 481 Restarting OpenVPN tunnels/interfaces Jul 14 19:02:44 check_reload_status 481 Reloading filter -
ok i not able to post my logs right
here is my one drive and i posted it in a text file
log fileand what also drives me crazy is if i google and i goto a link i get this stupid googleservices and it wont let me goto the damn link is there anything in pfsense can fix that problem
constant bs i tell yahere is a screen shot for the vpn gateway fail over
so i used to have both to tier 1 in the past but i watched another video they said
you do Tier 1 and Tier 2 so you have the usa first and if it fails it moves to 2nd one..i also enabled the interface for new york vpn but i still get those gateway errors... do you think its killing the php stalling it from all those errors of the tier 1 no gateway?
as i made this this way so i can switch back and forth from usa to canada if needed but mostly stick on the canada one
-
The logs look like you're seeing packet loss on the PPPoE WAN and then obviously seeing similar loss on all the VPNs that are over the WAN.
That in turn is triggering other processes for each gateway event.The first thing I would do there is set an external monitoring IP on the WAN so you're not reliant on the ISP gateway responding to pings.
Are you routing all traffic via that VPN gateway group?
-
so i have my network split so some IPs go out the VPN and others go out the WAN
so the WAN has a built in monitor IP the 2 vpns i set the monitor ips from setups setting up PIA
and what does the monitor IP actually do?
and what ip should i set it?so you mentioned to change the monitor ip from the isp whats the purpose of that.. for like when i mention it seems to stall out and then i can sometimes ping 1.1.1.1 but i cant ping google.ca or any dns name just ip address..
and here is the screen shot
-
and i dont know why the one vpn says dynamic both should say dynamic in the settings but one replaces the dynamic with an ip
-
@stephenw10
i added some new logsi set the Wan monitor to 1.0.0.1 i couldnt set it to 1.1.1.1 and i lost interent nothing worked.. i could ping 1.1.1.1 from the desktop but i couldnt ping google.ca
i had to reboot pfsense
so i got a log of the wan monitor ip 1.0.0.1 and one after i rebooted same link as i sent ya
-
The gateway monitoring serves two purposes. It generates data for the WAN quality logging in Status > Monitoring so you can see how your WAN varies over time. It is used to detect a connection that has failed (depending how that is defined) so in a gateway group it can be added or removed; like you have with the VPN group.
Since you only have one real WAN you don't need a failover action with that so you could set
Disable Gateway Monitoring Actionon that. That way it won't trigger unnecessary service starts when there is packet loss on it. You need that action on the VPN gateways in order to failover between them but you could set the thresholds higher so 20% packet loss doesn't trigger it if you regularly see that.The NY VPN shows as 'dynamic' because it's not connected. That gateway IP is pushed by the server when it connects.
1.0.0.1 should be valid as a monitoring IP, I would expect that to work fine normally.
How do you have DNS configured? Is it setup to only use the VPN gateways for example? That would explain why you could ping an IP but not resolve anything if the VPN is reconnecting.
Also when you set those monitoring IPs pfSense adds a static route to them via the gateway they're on. So when testing connectivity from a LAN side client you should avoid any of those IPs in order to not get static routed via that.
