Upgrading from 2.7.2 tot 2.8.1 breaks

Gertjan

@vicking said in Upgrading from 2.7.2 tot 2.8.1 breaks:

but I had to plugin a network cable with working connection ....

Was mentionned on the same page - link above.
That's a feature ! The free "WAN NIC tester facility" has been build in....

And while testing, you get the latest versions of every file. At least, when done, unlike installing from a Windows ISO, you won't have to wait for ms-update to overhaul your entire system ones more again.

Not very convenient

Actually, even when this will probably never an issue for me, I can understand.

stephenw10

@Gertjan said in Upgrading from 2.7.2 tot 2.8.1 breaks:

That's a feature ! The free "WAN NIC tester facility" has been build in....

vicking

@Gertjan
Yeah, the problem now is that I couldn't configure the LAN side without losing a working connection.
So the device is now booting on 2.8.1 but only with a WAN side configured. No way I can get in the webconsole now.

Strange thing also is that normally it should be possible to go in a shell by console and configure some stuff or re-assign the LAN and WAN ports from there, but somehow my device will only show console output while booting but after that it stops. Also input doesn't work anymore when the device is booted and last message in console is: Bootup complete

patient0

@vicking said in Upgrading from 2.7.2 tot 2.8.1 breaks:

Strange thing also is that normally it should be possible to go in a shell by console and configure some stuff or re-assign the LAN and WAN

But you do see the boot menu and the boot up log on the serial console? Usually after the first boot right after installation you are asked to assign WAN and LAN.

The WAN settings you made in the installer for the installer only.

Could you paste the last ~10 lines you see on the serial console?

vicking

@patient0
We are almost up and running!

Last step is to actually connect it to my ISP :D

Now I hope this device is powerfull enough to handle my 500/500mbit PPPoE connection with the new if_pppoe driver!

stephenw10

Yes that will be an interesting test.

vicking

@stephenw10 Well, test passed!

But, somehow I can't setup a MTU of 1500 for my PPPoE connection with this new if_pppoe driver resulting in a mtu of 1492 where my ISP provides MTU of 1500 by putting the PPPoE vlan on a MTU of 1500 and the wan MTU to 1508. In version 2.7.2 without the new if_pppoe I was able to set a MTU for the vlan, but in this version not anymore.

stephenw10

You need to assign the parent NIC and set the MTU there to 1508.

I have that running here and it works fine:

[2.8.1-RELEASE][admin@pfsense.fire.box]/root: ifconfig -v igb1
igb1: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1508
	description: BT_MODEM
	options=48100b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER,HWSTATS,MEXTPG>
	ether 00:01:21:01:aa:7c
	inet 192.168.102.10 netmask 0xffffff00 broadcast 192.168.102.255
	inet6 fe80::201:21ff:fe01:aa7c%igb1 prefixlen 64 scopeid 0x2
	media: Ethernet autoselect (1000baseT <full-duplex>)
	status: active
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	drivername: igb1
[2.8.1-RELEASE][admin@pfsense.fire.box]/root: ifconfig -v pppoe1
pppoe1: flags=1008851<UP,POINTOPOINT,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
	description: BT
	options=0
	inet X.X.X.X --> 172.16.13.252 netmask 0xffffffff
	inet6 fe80::201:21ff:fe01:aa7b%pppoe1 prefixlen 64 scopeid 0x19
	groups: pppoec
	nd6 options=123<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL,NO_DAD>
	drivername: pppoec1

vicking

@stephenw10 I've put the WAN mtu to 1500 instead of 1508 and now I also have a MTU of 1500, so seems to be solved.

Not bad for this device including traffic shaper to reduce bufferbloat! :)

stephenw10

Nice