Dual WAN, One ISP, balancing possible?
-
Hi
Im pretty sure the original poster has BBB Sweden as ISP. They provide med with an 100/10mbit connection, with that I get 5 public IPs and the weird thing is, as the original poster said, that they dont limit the upload anywhere. I will only have 100mbit down in total but I get 10mbit upload per IP so in a sense I have a 100/50mbit connection if I could only use all 5 IPs bandwith at the same time. I would settle for 20 or 30mbits though :) I dont want to have it in total at the same time though as per the original poster, I just want to be able to utilize the 10mbit connections for different servers.
Lets say for example that I have an ftpserver and my main computer, could I with pfsense and the virtual IP-thing suggested above have my FTP-server use one of the 10mbit and my main computer the other? You might say then why dont just place the FTP server on a public IP directly, well I just want to have all this behind one firewall.
-
No you can not use the load balancer when both interfaces share the same address space or gateway.
-
Dear
I bought a hardware with dual wan and put two wire from my hub.
the two WANS IP (10.175.175.1/8,10.175.175.2/8) and they have same GW 10.1.1.1
and the bandwidth double and its workbut how I make this with pfsense?
Regards
-
Dear
I bought a hardware with dual wan and put two wire from my hub.
the two WANS IP (10.175.175.1/8,10.175.175.2/8) and they have same GW 10.1.1.1
and the bandwidth double and its workbut how I make this with pfsense?
Regards
The solution is right above in this thread. Please read more closely.
-
Dear
What I want to say why the hardware make the sum of bandwidth without error and why the pfsense cant do ??? :-\
-
Dear
What I want to say why the hardware make the sum of bandwidth without error and why the pfsense cant do ??? :-\
I don't understand this sentence. Please try to find some other words.
-
sory for my bad english
but I want to know can pfsense sum bandwith for 10 WAN IP (same gateway) like the hardware dual wan (SMCBR24Q) and if no …......... why ?
-
It can, but you need different gateways (at least if you want to balance it). Other option is to use 1:1 or advanced outbond nat like described above but that won't give you balancing but only simultaneous use by different clients.
-
dear
And in future is it support?
and If I make advance NAT is it sum the bandwidth ?and many thaks for you ;D
-
I think bill said in a similiar thread that it could be done but our gui doesn't support it. If that is the case we might add support for it later.
If you use advanced outbound NAT it will sum up the bandwidth but you need several clients to use all of the bandwidth. None of the clients can use more than one IPs up/down restrictions though.
-
OK
If I make this topology
10 ip one GW 1 IP and 9 Sub configure with multi GW
ISP –-------------- Switch----------Router----------------pfsense-------------------------------------ISA Server-------Clients
it is work ?
and really I need make this work and I am sorry for disturb you :P -
I honestly haven't read this entire thread but I can confirm that you can load balance with the same actual gateway using routers. Here is my setup:
/–----routera10.10.10.1---------Wan-10.10.10.10
ISP
-------routerb11.11.11.1---------opt1wan2-11.1.11.11
I set it up like that and it worked just dandy.I will also tell you that I tried it like this:
/------DSLtransprentPPPoEmode---------Wan-PPPoE
ISP
-------routerb11.11.11.1---------opt1wan2-11.1.11.11
and if failed, not sure why though. It may have just been when I tried that particular setup, I put in a rule incorrectly. Anyways, hope that helps. Also if your having dns problems after doing this, the routing tables may be going screwy, but so far it hasn't happned for me. -
I will also tell you that I tried it like this:
/–----DSLtransprentPPPoEmode---------Wan-PPPoE
ISP
-------routerb11.11.11.1---------opt1wan2-11.1.11.11
and if failed, not sure why though.There is a known bug that prevents usage of a PPPoE connection for pools. We are working on fixing this.
-
Dears
But as you see I have 10 IP that mean I need 10 routers or I make Vlans???
or I can make Sub IP in the external router (only One router) and I configure pfsense to use every sub IP as a gatewayplease see the attachment this is my Topology and the second one I need to do it Can I ?
-
please any answer
-
As hoba said, this DOES NOT work currently. Sorry!
-
Thanks alot
any another software you preferd ??
-
If you have one isp and 1 internal server it's pointless.
And I do not see why you want it either.
-
Dears
Hi agian
I make this toplology by combine pfsense and mikrotik in one pc (VMWARE)
and when I download with accelarator is download from all ip and when download from IE it download from one IP .
is this OK and not make problems