PCEngines alix2c3 (Substitute for WRAP) boot failes
-
does anyone know what I need to do to get past this point? I have a 4GB FAT16 formatted CF drive, I've used the 'file copy' method of installing freedos onto it. The ALIX board will boot and display the following:
InitDiskBad or missing Command Interpreter: command.com /P /E:256
Enter the full shell command line:i've tried various combinations of typing 'command.com', c:\command.com, etc. etc. But have yet to get past this stage.
-
Contact PCEngines and get the newest BIOS.
-
What do you mean? The only reason I am trying to boot to CF is so that I can flash the newest BIOS…
-
Huh? You can flash the bios from within the bios itself…
I suggest contacting PCEngines for more info.
-
I've sent off an email to pc engines, but seeing as it sounds like you know how to do this, can you help out at all?
-
I do not have a WRAP board and do not remember the key combination that brings up the BIOS screen. Sorry.
-
does anyone know what I need to do to get past this point? I have a 4GB FAT16 formatted CF drive, I've used the 'file copy' method of installing freedos onto it. The ALIX board will boot and display the following:
InitDiskBad or missing Command Interpreter: command.com /P /E:256
Enter the full shell command line:i've tried various combinations of typing 'command.com', c:\command.com, etc. etc. But have yet to get past this stage.
Hmmm - I was under the impression that DOS had a 2-Gig filesystem size limitation… that is not the case??
gm...
-
I do not have a WRAP board and do not remember the key combination that brings up the BIOS screen. Sorry.
I can get to the BIOS screen itself by pressing 's' as the system boots. There is an option there for xmodem transfer there, but of course I don't know what format the bios firmware needs to be in.
–regarding the CF card, windows will let me format it as FAT16, so I assume that means there isn't a problem
-
–regarding the CF card, windows will let me format it as FAT16, so I assume that means there isn't a problem
Well - maybe and maybe not.
I am not very familiar with the DOS version used but if it is formatted with 512-byte hard-disk sector record size then the 8-bit sector to cluster size would be 32-kbyte which yields a total of 2-Gbyte using a 32-bit cluster counter (most DOS versions used this standard). There is an "extended" FAT-16 version which is used by later versions of Windows that yields the 4-Gbyte per drive storage value - I suspect you are using either Windows XP or Vista to format the CF device??
I am thinking the DOS version used follows the older 512-byte/sector format and would only be able to address 2-Gbyte total but that is just me :)
I have used several CF devices (64-meg, 128-meg, 512-meg and 1-gig) to test the bios loader and they all worked - I tried using a 4-gig CF card but the physwritedisk program I used responded back that it could only write to a maximum of 2-gig and I had requested it write to a 4-gig device.
gm…
-
I'm sorry that I made a fool of myself and perhaps also confused some of you with my latest post. My failure with bios 0.98g was only because I had chosen the wrong bios file. As usual it was only a matter of not reading properly. It was all there in the sbyoon's post.
You can download and write it to any cf card with 'physdiskwrite'. This image includs the 0.98g bios update files for Alix2. If you have Alix2, just execute 'sb.com' after freedos boot up.
So, the success story for me was:
1. Download sbyoon's image
2. Use physdiskwrite and write the image to an old 64MB CF
3. Boot it on my Alix2 card
4. Press 's' during bootup sequence and choose 'L' for LBA mode
5. Quit, save and continue booting
6. At the FreeDOS-prompt: Type SB.COM (This time with the original Alix1.bin on the FreeDOS disk!)
7. Power off and change CF
8. Successfully boot psSense 1.2-RC3 Embedded
9. Yeehaaa!/Roger
-
In my book the ONLY foolish question is the one you DON'T ASK! ;D
Glad to see you have the Alix up and running!!!
gm…
-
Just upgraded my 2c2 to Bios 0.98g
pfsense works like a champ with the todays snapshot incl. OpenVpnEven it is only the 433 MHz/128MB Version it works fine on my 30/2 Mbit cable Line
Real nice work guys.
Keep this nice work going -
@Rusty64bit:
Just upgraded my 2c2 to Bios 0.98g
pfsense works like a champ with the todays snapshot incl. OpenVpnCould you test if reboot works, please? My 1.2-RC3 panics during reboot but it reboots. If I use the pfsense-1024-image the cpu got hung during reboot and I have to pull the plug :-(
BTW. You can see the panic at the seriell console, only.Bye,
eweri -
Works fine
No issues
I took the image for the snapshot server yesterday
But one thing
Do you have the 2c3 or like i the 2c2 this is the 433MHz 128MB 3Nic without USB ?
Do know this makes a difference…Pascal just put Version 0.99 out on the Pc Engines Website...
-
Hello Eweri,
I have to investigate for reboot. It seems working, I can't serial connect at the moment.
Here is the solution for full install (I wrote the last part, Using VirtualBox) :
http://devwiki.pfsense.org/FullInstallOnWRAPBut it's not a good idea on CF! CF don't support too much write cycle! You are warn!
Bye
Sorry Eweri, I forgot you. Same answer : no issue at all with reboot on 1.2RC3 10/26/2007.
Bye
-
This is my dmesg output
Copyright
1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p9 #0: Mon Dec 10 04:26:02 EST 2007
sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by AMD PCS (431.65-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x5a2 Stepping = 2
Features=0x88a93d <fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx>AMD Features=0xc0400000 <mmx+,3dnow+,3dnow>real memory = 134217728 (128 MB)
avail memory = 121872384 (116 MB)
pnpbios: Bad PnP BIOS data checksum
wlan: mac acl policy registered
K6-family MTRR support enabled (2 registers)
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
MFGPT bar: f00100006200
pci0: <encrypt decrypt,="" entertainment="" crypto="">at device 1.2 (no driver attached)
vr0: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1000-0x10ff mem 0xe0000000-0xe00000ff irq 10 at device 9.0 on pci0
miibus0: <mii bus="">on vr0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:0d:b9:12:9f:84
vr1: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1400-0x14ff mem 0xe0040000-0xe00400ff irq 11 at device 10.0 on pci0
miibus1: <mii bus="">on vr1
ukphy1: <generic ieee="" 802.3u="" media="" interface="">on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr1: Ethernet address: 00:0d:b9:12:9f:85
vr2: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1800-0x18ff mem 0xe0080000-0xe00800ff irq 12 at device 11.0 on pci0
miibus2: <mii bus="">on vr2
ukphy2: <generic ieee="" 802.3u="" media="" interface="">on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr2: Ethernet address: 00:0d:b9:12:9f:86
ath0: <atheros 5212="">mem 0xe00c0000-0xe00cffff irq 9 at device 12.0 on pci0
ath0: Ethernet address: 00:02:6f:44:30:4b
ath0: mac 10.4 phy 6.1 radio 6.3
isab0: <pci-isa bridge="">port 0x6000-0x6007,0x6100-0x61ff,0x6200-0x623f,0x9d00-0x9d7f,0x9c00-0x9c3f at device 15.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <generic ata="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 15.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
ohci0: <ohci (generic)="" usb="" controller="">mem 0xefffe000-0xefffefff irq 15 at device 15.4 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ohci (generic)="" usb="" controller="">on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ehci0: <amd cs5536="" usb="" 2.0="" controller="">mem 0xefffd000-0xefffdfff irq 15 at device 15.5 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: companion controller, 4 ports each: usb0
usb1: <amd cs5536="" usb="" 2.0="" controller="">on ehci0
usb1: USB revision 2.0
uhub1: AMD EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
orm0: <isa option="" rom="">at iomem 0xe0000-0xeafff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80 <clock_battery>Timecounter "TSC" frequency 431646313 Hz quality 800
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 967MB <cf 20070131="" card="" 1gb="">at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense___
/ f \
/ p \/ Sense
\/ \
\/Welcome to pfSense 1.2-RC3 on the 'embedded' platform…
Setting up embedded specific environment...
done.
Mounting filesystems...
done.
Creating symlinks...
.
.
.
done.
Launching PHP init system...
done.
Initializing...
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
done.
Starting device manager (devd)...
done.
Loading configuration...
.
.
.
done.
Updating configuration...
done.
Cleaning backup cache...
done.
Setting up extended sysctls...
done.
Syncing user passwords...
done.
Starting Secure Shell Services...
done.
Setting timezone...
done.
Starting syslog...
done.
Configuring LAN interface...
vr0: link state changed to UP
vr1: link state changed to UP
vr2: link state changed to DOWN
done.
Configuring WAN interface...
done.
Configuring OPT interfaces...
done.
Configuring CARP interfaces...
done.
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
route:
writing to routing socket
:
No such process
Syncing system time before startup...
done.
pflog0: promiscuous mode enabled
Configuring firewall...
.
.
.
done.
Starting webConfigurator...
done.
Starting DHCP service...
done.
Starting DNS forwarder...
done.
Setting up microcode and tx/rx offloading...
done.
Starting FTP helpers...
done.
Generating RRD graphs...
route:
writing to routing socket
:
No such process
done.
Starting DHCP service...
done.
Starting OpenNTP time client...
done.
Starting CRON...
done.
Executing rc.d items...
Starting /usr/local/etc/rc.d/*.sh...
done.
appending output to nohup.out
Bootup completeFreeBSD/i386 (pfSense.local) (console)
*** Welcome to pfSense 1.2-RC3-embedded on pfSense ***
LAN* -> vr0 -> 192.168.178.1
WAN* -> vr1 -> 0.0.0.0(DHCP)
OPT1(OPT1) -> vr2 -> NONE
pfSense console setup
0) Logout (SSH only)
1) Assign Interfaces
2) Set LAN IP address
3) Reset webConfigurator password
4) Reset to factory defaults
5) Reboot system
6) Halt system
7) Ping host
8) Shell
9) PFtop
10) Filter Logs
11) Restart webConfigurator
12) pfSense PHP shell
13) Upgrade from consoleEnter an option:
vr0: Using force reset command.</cf></clock_battery></isa></amd></amd></ohci></ohci></ata></ata></generic></isa></pci-isa></atheros></generic></mii></via></generic></mii></via></generic></mii></via></encrypt></pci></host></mmx+,3dnow+,3dnow></fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx> -
Could you test if reboot works, please? My 1.2-RC3 panics during reboot but it reboots. If I use the pfsense-1024-image the cpu got hung during reboot and I have to pull the plug :-(
BTW. You can see the panic at the seriell console, only.Bye,
eweriJust reply to my self: Installed tinyBIOS 0.99 today and now I have no reboot issues any more. Going to try the 1024MB image and see if the reboot-hung is gone also.
Bye,
eweri -
Just reply to my self: Installed tinyBIOS 0.99 today and now I have no reboot issues any more. Going to try the 1024MB image and see if the reboot-hung is gone also.
Bad news: it still panics with the pfsense-1024MB-image and got hung until i pull the plug :(
Here is the console output:
pfSense is now shutting down …
Waiting (max 60 seconds) for system process
vnlru' to stop...done Waiting (max 60 seconds) for system processbufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 done
All buffers synced.
Uptime: 4m3s
ukphy0: detached
miibus0: detached
ukphy1: detached
miibus1: detached
ukphy2: detached
miibus2: detached
Rebooting...
Keyboard reset did not work, attempting CPU shutdown
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc3faae10
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc05ef0ae
stack pointer = 0x28:0xc7d44c04
frame pointer = 0x28:0xc7d44c0c
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = 1 (init)
trap number = 12
panic: page fault
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc196ed28
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc061add2
stack pointer = 0x28:0xc7d44b1c
frame pointer = 0x28:0xc7d44b4c
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = 1 (init)
trap number = 12
panic: page fault
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc196ed28
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc061add2
stack pointer = 0x28:0xc7d44a34
frame pointer = 0x28:0xc7d44a64
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = 1 (init)
trap number = 12
panic: page fault
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc196ed28
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc061add2
stack pointer = 0x28:0xc7d4494c
frame pointer = 0x28:0xc7d4497c
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = 1 (init)
trap number = 12
panic: page fault
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc196ed28
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc061add2
stack pointer = 0x28:0xc7d44864
frame pointer = 0x28:0xc7d44894
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = 1 (init)
trap number = 12
panic: page fault
kernel trap 12 with interrupts disabledFatal trap 12: page fault while in kernel mode
fault virtual address = 0xc196ed28
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc061add2
stack pointer = 0x28:0xc7d4477c
frame pointer = 0x28:0xc7d447ac
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = resume, IOPL = 0
current process = kk
Fatal double fault:
eip = 0xc0635d0e
esp = 0xc7d43fe0
ebp = 0xc7d440a8
panic: double fault
Uptime: 4m6s
Cannot dump. No dump device defined.
Automatic reboot in 15 seconds - press a key on the console to abort -
As I can see the 1024 image from http://snapshots.pfsense.com/FreeBSD6/RELENG_1_2/embedded/1024/ is pretty old (10/14/07).
Please can you upgrade to lastest snapshot using file http://snapshots.pfsense.com/FreeBSD6/RELENG_1_2/updates/pfSense-Embedded-Update-1.2-RC3.tgz? You have to use the upgrade utility provided in the console (option 13) through SSH or serial connection.My 2 cents…
-
Does anyone have any thoughts as to why I might still be getting a kernel panic? I've updated to .99 for the bios. I've installed the full version of pfSense 1.2 rc3 onto a 4GB microdrive.