SquidGuard and blank redirects?
-
You config have
redirect https://192.168.1.1/sgerror.php?url=http%3A%2F%2Fwww.kmaconnect.com&a=%a&n=%n&i=%i&s=%s&t=%t&u=%uMust be
redirect https://192.168.1.1/sgerror.php?url=http://www.kmaconnect.com&a=%a&n=%n&i=%i&s=%s&t=%t&u=%uBug already fixed for '%3A%2F%2F'
-
Oh, I understand. You want me to install the newest version of SG. I'll do that. Thanks.
Chris
-
Oh, I understand. You want me to install the newest version of SG. I'll do that. Thanks.
Chris
Language barrier in action :D
-
;D Yep ;D
-
No reboot required Chris.
-
hello!
I've upgraded squidguard to the latest version and i have pfsense webgui running in https mode.
Also squid is in trasparent mode.I've made a block list of domains on squidguard which works but instead of redirecting to a local web server ip it shows a error page like this:https://192.168.1.1/sgerror.php?
can anyone tell me how can i avoid this?
-
If you read this thread carefully, you'll see that is a problem that others have run into. There is something in this package that does not re-direct properly when you have your webGUID set to HTTPS. I am not aware of any work around.
dvserg, have you been able to reproduce this behavior? Do you have any idea what's going on with that? ???
Thanks!
-
I believe dvserg has fixed this issue, but I have not tried the newest version yet. It almost sounds to me like acidrop hasn't put anything in the Default Redirect section of the default tab. Have you entered in a URL in that section acidrop
Chris
-
hello ciarocci!
first of all i've read all articles but i didn't fully understood what's going on.. :)
secondly yes i've put in default redirect an url (a local web server address which points to a page that says: "this page is blocked by your admin") but instead of this appears the error that i told you before… -
acidrop, try putting your pfSense webGUI back on http and see what happens. You may have to apply changes again in SquidGuard after you do that. There might still be a problem with this working in HTTPS? DVSerg? I myself am unable to change my webGUI to port 80 because it just won't change no matter how many times I apply the change, but that is another issue and others have said they have no problem doing that. Give that a try and report back.
Chris
-
hi
I tried that and if i put webgui at port 80 everything works ok.Just on https is the problem….
Also i have another issue which isn't something new...when i restart pfsense squidguard service doesn't start
automatically although it's enabled..i have to press apply again to make it work -
Hi all
Still, the problem remains with HTTPS?
Please say - this problem bof modes: on transparent and on non-transparent?
–-
To acidrop - yes, this bug exists and i know about.PS thanks all for replaying. :)
-
hi dvserg !
I've checked it on both transparent and non transparent mode and the problem is the same.
-
Confirmed. On HTTPS the errors still persist.
-
Same problem for me :(
-
the error is now corrected…de-install squidguard and install again..you will see a new option on the general settings: Redirect mode
-
Awesome, the redirects work as planned. One thing to note, the redirects do not work if you put them in the "Destinations" section.
-
Awesome, the redirects work as planned. One thing to note, the redirects do not work if you put them in the "Destinations" section.
How does it happens? Example exists?
-
I think I spoke too soon. I tried to re-create the problem and give you an example and I could not. Maybe I just didn't give the APPLY button the good old "hit it twice" try. :-)
Chris
-
first off squidGuard has been working great thank you. I recently switched pfSense webGUI to https and now by errors page are not working. it gives and error that requested URL could not be retrieved. I scanned through this page and I was curious if a work around has been found so that the custom error message would appear. prior when i was running the standard port 80 it worked fine FYI
thanks!