Kernel Panic

eri--

Can you please send me your config?

vito

ermal
My system has been good so far.
i just updated another firewall and will let you know.

Thanks again for your help.

geewhz01

@ermal:

Can you please send me your config?

I have sent borh the primary and secondary. Let me know if I can be of further assistance.

Thanks,

Andy

eri--

I committed a fix for this issue too.
So grab a snapshot from late tomorrow and test.

geewhz01

Still a problem for me. Secondary locked a few minutes after a rule change. Running AMD64 20110201-1959.

Thanks,

Andy

pfsense2211.png_thumb

eri--

Confirmed fix since i found a way to reproduce it.
Snapshots of tomorrow should be ok.

jnorell

A quick note, I updated my carp slave to Feb 2 04:04:51 EST 2011 with some of the recent kernel panic fixes, but I'm still able to panic it by adding a new VIP addr. (I deleted a VIP addr, no problem; then re-added that addr, no problem; then added a new VIP addr, and it panic'd in devd again.)

fasteddy

I looked through a similar topic (http://forum.pfsense.org/index.php/topic,31721.0.html) but wasn't entirely convinced I'm having the same issue, so a new topic seemed to be in order…

I have had an IPSec site-to-site VPN connection running trouble-free for months now using two pfSense PCs running 2.0 BETA i386 snapshots from May of 2010. After updating to a January 27th snapshot (and snapshots from every day since, including today) I'm having problems with one of the PCs locking up. Without fail, if I attempt to log on to the web configuration page of the remote pfSense box through the VPN connection, it will serve up the 'login' page, but crashes as soon as I hit the 'login' button. The error message on the pfSense box's monitor says:


Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address   = 0xd79a2720
fault code              = supervisor read, page not present
instruction pointer     = 0x20:0xd79a2720
stack pointer           = 0x28:0xc5b26bbc
frame pointer           = 0x28:0xc5b26bc8
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 0 (em3 taskq)

I've attached a picture of the backtrace information as well.

If I do a remote desktop connection to a PC on the remote side of the VPN, I can access the web configuration through that PC's browser with no issues. The problem only occurs if I try to access the web configuration of the remote pfSense box (or ssh console, for that matter) directly from a machine on the local side of the VPN. I've been doing this with no problems until I updated on the 27th.

For what it's worth, this only happens on one of my two machines - if I'm on the 'sick' pfSense box's network I can access the 'healthy' pfSense box's web configuration directly through the VPN with no issues. The two PCs are substantially different, but are using the same network cards - Intel Pro/1000MT gigabit NICs. The 'sick' pfSense box also has an on-board Marvell Yukon Gigabit interface (skc0).

The output of 'pciconf -lvp' is:


skc0@pci0:0:10:0:       class=0x020000 card=0x811a1043 chip=0x432011ab rev=0x13 hdr=0x00
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 32, base 0xfa000000, size 16384, enabled
    bar   [14] = type I/O Port, range 32, base 0xa000, size 256, enabled
em0@pci0:0:11:0:        class=0x020000 card=0x13768086 chip=0x107c8086 rev=0x05 hdr=0x00
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 32, base 0xfa300000, size 131072, enabled
    bar   [14] = type Memory, range 32, base 0xfa200000, size 131072, enabled
    bar   [18] = type I/O Port, range 32, base 0xa400, size 64, enabled
em1@pci0:0:12:0:        class=0x020000 card=0x13768086 chip=0x107c8086 rev=0x05 hdr=0x00
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 32, base 0xfa600000, size 131072, enabled
    bar   [14] = type Memory, range 32, base 0xfa500000, size 131072, enabled
    bar   [18] = type I/O Port, range 32, base 0xa800, size 64, enabled
em2@pci0:0:13:0:        class=0x020000 card=0x13768086 chip=0x107c8086 rev=0x05 hdr=0x00
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 32, base 0xfa900000, size 131072, enabled
    bar   [14] = type Memory, range 32, base 0xfa800000, size 131072, enabled
    bar   [18] = type I/O Port, range 32, base 0xb000, size 64, enabled
em3@pci0:0:14:0:        class=0x020000 card=0x13768086 chip=0x107c8086 rev=0x05 hdr=0x00
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 32, base 0xfac00000, size 131072, enabled
    bar   [14] = type Memory, range 32, base 0xfab00000, size 131072, enabled
    bar   [18] = type I/O Port, range 32, base 0xb400, size 64, enabled

Any chance someone could shed some light on this issue? I can reliably reproduce the issue if need be, and would be happy to provide any additional information that may be required.

Thank you, and best regards!

fasteddy_backtrace.jpg_thumb

jimp

The snap from 2/3 would be the first to have the carp panic fixes.

There is still an issue (when deleting a VIP) but the panic you're seeing has likely been fixed in the most recent snap that is up now (Thu Feb 3 00:55:19 EST 2011)

FisherKing

Hi Jimp - My read of the build logs suggested that Ermal's patch didn't get included in last nights build even though the build was started after the commit was made.

Thu Feb 3 04:21:58 EST 2011 -|- >>> Sleeping for 86400 in between snapshot builder runs. Last known commit 847e5e8257b58906a0d12ce48275cae7162aab47

That commit listed there shows up in redmine as being a couple before ermals commit. Am I reading that wrong?

jimp

I started the builder by hand after his commit.
The patches are committed in the tools repo - the tools repo isn't tracked by the builder in the function you pasted.

FisherKing

Hmmm - Just panicked, running 2.0-BETA5 (i386) built on Thu Feb 3 00:55:19 EST 2011 on both master & slave.

Updated a rule on the master, slave panicked.

I've attached images of the panic & bt.

![](http://Carp panic.png)
![](http://Carp bt.png)

![Carp panic.png](/public/imported_attachments/1/Carp panic.png)
![Carp panic.png_thumb](/public/imported_attachments/1/Carp panic.png_thumb)
![Carp bt.png](/public/imported_attachments/1/Carp bt.png)
![Carp bt.png_thumb](/public/imported_attachments/1/Carp bt.png_thumb)

eri--

The issue is fixed. Just the patch i committed had some typo from copy/pasto.

eri--

You should grab the next snapshot that will come out.
AFAIK it has no more such issues.

jimp

I just started a new build after ermal's commit - the next new snapshot should include this fix.

fasteddy

Thanks Ermal! I'll give the next snapshot a try when it is available and report back.

FisherKing

Running 2.0-BETA5 (i386) built on Thu Feb 3 18:55:08 EST 2011 on both master & slave.

Slave panicked as soon as I updated a rule on the master.

Attached images of both panic & bt.

![](http://Carp Panic.png)

![](http://carp bt.png)

![Carp Panic.png](/public/imported_attachments/1/Carp Panic.png)
![Carp Panic.png_thumb](/public/imported_attachments/1/Carp Panic.png_thumb)
![carp bt.png](/public/imported_attachments/1/carp bt.png)
![carp bt.png_thumb](/public/imported_attachments/1/carp bt.png_thumb)

eri--

Wrong snapshot sorry.
This is the commit that fixes the error https://rcs.pfsense.org/projects/pfsense-tools/repos/mainline/commits/08f1322c7d5d9fae8ef52dc356c75a59d2483263

FisherKing

Running 2.0-BETA5 (i386) built on Fri Feb 4 02:36:03 EST 2011 on both Master & Slave.

It ran longer this time before the panic. I changed my configuration a little before it happened this time.

Steps:
1 - Pulled the plug on the master WAN
(Slave became the new CARP master for all carp VIPs)
1a - Verified LAN clients were able to surf the web.
2 - Cleared XMLRPC Sync settings from the old master
3 - Set XMLRPC Sync settings on the new master (old slave)
4 - Changed DHCP settings on new master (old slave)
5 - Old master had a panic.

![](http://Carp Panic1.png)

![](http://carp bt1.png)

![Carp Panic1.png](/public/imported_attachments/1/Carp Panic1.png)
![Carp Panic1.png_thumb](/public/imported_attachments/1/Carp Panic1.png_thumb)
![carp bt1.png](/public/imported_attachments/1/carp bt1.png)
![carp bt1.png_thumb](/public/imported_attachments/1/carp bt1.png_thumb)

jimp

@PJ2:

2 - Cleared XMLRPC Sync settings from the old master
3 - Set XMLRPC Sync settings on the new master (old slave)

Why on earth would you do that? That isn't necessary at all, and could lead to other issues.