2 wan ip only 1 gateway no work after update

burff

i have a pfsense 2.0 with two ip public 200.x.x.114/28 and 200.x.x.115/28 the gateway is 200.x.x.113. In a version 1.2.3 work perfect but after upgrade the second WAN 200.x.x.115 no work more in a public network. i try create again the opt1 interface and gateway for opt1 but no work. i can put other ip public in a machine to try ping to opt1 200.x.x.115 and i can ping to this ip but when i pinging of other location the opt1 no work i think is a route problem but i cant resolve please help

netstat -r

Routing tables

Internet:
Destination Gateway Flags Refs Use Netif Expire
default 200.x.x.113 UGS 0 7759 re0
10.0.8.0 10.0.8.2 UGS 0 163428 ovpns6
10.0.8.1 link#16 UHS 0 0 lo0
10.0.8.2 link#16 UH 0 0 ovpns6
10.6.6.1 link#12 UHS 0 0 lo0
10.6.6.2 link#12 UH 0 0 ovpns3
10.88.99.1 link#13 UHS 0 0 lo0
10.88.99.2 link#13 UH 0 0 ovpns4
10.168.174.1 link#14 UHS 0 0 lo0
10.168.174.2 link#14 UH 0 0 ovpns5
localhost link#5 UH 0 474 lo0
172.16.100.1 link#11 UHS 0 0 lo0
172.16.100.2 link#11 UH 0 0 ovpns2
192.168.60.0 10.6.6.2 UGS 0 0 ovpns3
192.168.173.0 10.88.99.2 UGS 0 76815 ovpns4
192.168.174.0 10.168.174.2 UGS 0 71211 ovpns5
192.168.175.0 link#3 U 0 1451946 nfe0
pfsense link#3 UHS 0 0 lo0
192.168.254.0 172.16.100.2 UGS 0 180928 ovpns2
200.44.32.12 200.74.197.113 UGHS 0 110393 re0
200.x.x.112/28 link#2 U 0 62353 rl0
200.x.x.114 link#2 UHS 0 0 lo0
200.x.x.115 link#1 UHS 0 0 lo0
200.x.x.116 link#9 UHS 0 0 lo0
208.67.220.220 200.x.x.113 UGHS 0 110449 re0
208.67.222.222 200.x.x.113 UGHS 0 110457 re0

wan(200.x.x.114)
lan (192.168.175.1)< hub gateway(200.x.x.113)
opt1(200.x.x.115)

marcelloc

You do not need opt1 for second wan ip. Both are on same subnet.

Just Create an Ip alias at wan interface and it will work.

burff

i can use alias but the rules and nat over firewall work in ip of alias? i need separe rules

marcelloc

@burff:

i can use alias but the rules and nat over firewall work in ip of alias? i need separe rules

Set outbound nat to manual and set your rules.

Use same network on two interfaces is not correct unless you are using bridge.

burff

the rules are inbound and in the GUI in interface WAN i cant see alias for the interface wan

marcelloc

Alias are in 'virtual ip' gui tab.

KingsX

I were using four external interfaces during 1.2.3 with the same gateway since this allows me to get 4 times the upload from my provider.

Now with 2.0 it won't work as stated before. Is the stated solution usable on my setup as well.
I'm using DCHP on my WAN-ports and are trying to loadbalance outbound between them.

burff

alias in virtual ip work for me
work for statick ips in dhcp mode i dont know

KingsX

@burff:

alias in virtual ip work for me
work for statick ips in dhcp mode i dont know

That was the question since I can't find any virtual dynamic IP.

marcelloc

Multiple dhcp clients on same net sounds completely unusual and routing confusing to me.

KingsX

Reason is stated earlier but I'll explain further…

I have a LAN provider who gives me 100Mbps download but only 10Mbps upload. They provide me with five IP-addresses through DHCP and each of the IPs each get 10Mbps of upload. Since they give me IP-addresses from a /16 net I get the same gateway on all IPs. This means if I put a firewall with five WAN-addresses and load-balance them I get 50Mbps upload. It works with 1.2.3, not flawless but it works, and I have also used Shorewall to do this job and am now asking you if I can do this with pfsense 2.0?

I'm currently trying to provide enough bandwidth to host a couple of game servers and really need the extra 30-40Mbps I'm trying to get here.

Sorry if I don't make any sense...