My pfSense keeps breaking (novel inside…)
-
I'm posting this connected through the DSL router. So I know for a fact the router is working great.
Here's traceroute from my laptop attached to one of the other ports on the DSL router:
C:\Users\Administrator>tracert 8.8.8.8
Tracing route to google-public-dns-a.google.com [8.8.8.8]
over a maximum of 30 hops:1 <1 ms <1 ms <1 ms 192.168.2.1
2 45 ms 45 ms 43 ms 10.39.5.1
3 50 ms 50 ms 49 ms at-3-2-0-1715.LAX01-CORE-RTR2.verizon-gni.net [1
30.81.194.2]
4 50 ms 51 ms 125 ms so-1-1-1-0.LAX01-BB-RTR2.verizon-gni.net [130.81
.16.130]
5 54 ms 51 ms 51 ms 0.so-6-0-0.XT2.LAX9.ALTER.NET [152.63.10.157]
6 122 ms 121 ms 121 ms 0.so-1-0-0.XT2.NYC4.ALTER.NET [152.63.64.126]
7 128 ms 133 ms 137 ms TenGigE0-7-0-0.GW8.NYC4.ALTER.NET [152.63.22.45]8 128 ms 127 ms 129 ms Internet-gw.customer.alter.net [152.179.72.66]
9 128 ms 129 ms 129 ms 72.14.238.232
10 122 ms 119 ms 133 ms 209.85.252.2
11 131 ms 132 ms 130 ms 72.14.239.93
12 126 ms 127 ms 129 ms 72.14.236.200
13 142 ms 143 ms 129 ms 216.239.49.145
14 129 ms 129 ms 128 ms google-public-dns-a.google.com [8.8.8.8]Trace complete.
-
Can you show a picture of your WAN interface configuration page? The one connected to your DSL modem??
-
Here are printscreens of both my Interface and Gateway setup for the WAN.
-
Your gateway cannot be the same as the IP on its own interface.
-
SORRY ABOUT THAT! Slight oversight the last time I reset to defaults. >_<
I've set it to the proper 192.168.2.1 now. (which it always has been except for the very last time I was setting it back up in a hurry and didn't pay attention). =/
Ok, so with that properly in place this is the situation:
Still can't get a connection THROUGH pfSense. (even though it seems to be FULLY communicating over both the WAN port and the LAN port).
When I run a traceroute from PFSENSE this is what I get:
netstat -rn -f inet; traceroute -n 8.8.8.8
Routing tablesInternet:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.2.1 UGS 0 19379 em2
4.2.2.2 192.168.2.2 UHS 0 14429 em2
10.39.5.1 192.168.2.1 UGHS 0 172195 em2
127.0.0.1 link#12 UH 0 10979 lo0
192.168.2.0/24 link#7 U 0 1989 em2
192.168.2.2 link#7 UHS 0 0 lo0
192.168.168.0/24 link#5 U 0 18742 em0
192.168.168.1 link#5 UHS 0 0 lo0
traceroute to 8.8.8.8 (8.8.8.8), 64 hops max, 52 byte packets
1 192.168.2.1 1.178 ms 0.298 ms 0.274 ms
2 10.39.5.1 41.901 ms 40.120 ms 39.915 ms
3 130.81.194.2 48.084 ms 48.009 ms 47.786 ms
4 130.81.16.130 52.014 ms 47.993 ms 48.036 ms
5 152.63.112.49 48.072 ms 48.021 ms 48.001 ms
6 152.63.64.126 113.913 ms 113.986 ms 114.065 ms
7 152.63.21.125 125.921 ms
152.63.16.125 134.030 ms
152.63.21.65 116.058 ms
8 152.179.72.66 127.841 ms 126.109 ms 127.908 ms
9 209.85.255.68 114.056 ms 116.028 ms
72.14.232.244 118.041 ms
10 209.85.251.37 127.852 ms
209.85.252.2 130.120 ms 130.018 ms
11 72.14.239.93 127.940 ms 128.042 ms 127.902 ms
12 72.14.236.200 126.165 ms 123.836 ms 125.851 ms
13 216.239.49.145 126.229 ms 125.828 ms 125.908 ms
14 8.8.8.8 124.284 ms 125.769 ms 128.827 msWhen I run a ping from pfSense this is what I get:
Ping output:
PING 8.8.8.8 (8.8.8.8) from 192.168.2.2: 56 data bytes
64 bytes from 8.8.8.8: icmp_seq=0 ttl=54 time=125.634 ms
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=124.157 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=125.198 ms–- 8.8.8.8 ping statistics ---
3 packets transmitted, 3 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 124.157/124.996/125.634/0.620 msBut when I run a traceroute from my COMPTUER I get:
C:\Users\Administrator>tracert 8.8.8.8Tracing route to 8.8.8.8 over a maximum of 30 hops
1 <1 ms <1 ms <1 ms 192.168.168.1
2 * * * Request timed out.
3 * * * Request timed out.
4 * * * Request timed out.
5 * * * Request timed out.
6 * * * Request timed out.
7 * ^CI also can't ping, or make any other connection to the outside world.
And AGAIN still not showing ANY states or ANYTHING in the firewall logs (even with logging turned on for the default rule. It won't even show what it's NOT blocking. It's just empty as always.)
-
Ok, so check this out as well…
I'm connect to the LAN port, so I'm testing pings on my laptop THROUGH pfSense and this is what I get:
C:\Users\Administrator>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.Ping statistics for 192.168.2.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),C:\Users\Administrator>ping 192.168.2.2
Pinging 192.168.2.2 with 32 bytes of data:
Reply from 192.168.2.2: bytes=32 time<1ms TTL=64
Reply from 192.168.2.2: bytes=32 time<1ms TTL=64
Reply from 192.168.2.2: bytes=32 time<1ms TTL=64
Reply from 192.168.2.2: bytes=32 time<1ms TTL=64Ping statistics for 192.168.2.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0msC:\Users\Administrator>ping 192.168.168.1
Pinging 192.168.168.1 with 32 bytes of data:
Reply from 192.168.168.1: bytes=32 time<1ms TTL=64
Reply from 192.168.168.1: bytes=32 time<1ms TTL=64
Reply from 192.168.168.1: bytes=32 time<1ms TTL=64
Reply from 192.168.168.1: bytes=32 time<1ms TTL=64Ping statistics for 192.168.168.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0msC:\Users\Administrator>ping 8.8.8.8
Pinging 8.8.8.8 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.Ping statistics for 8.8.8.8:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),So it'll respond to a ping on the port I'm directly connected to AND pass the ping along to the WAN interface, BUT it won't let anything past it. =/
-
I skimmed your posts but didn't see so hope this isn't redundant…
What do your outbound LAN rules and outbound port rules look like?
-
They're the factory defaults for right now. Since I've reset everything.
The ONLY thing I've changed on the rules is that I turned logging on for the "Default allow LAN to any rule".
Attached are some printscreens.
-
On the /firewall_nat_out.php page-
Try choosing "Manual Outbound NAT rule generation" save and see what results you get…
Assuming also that you have unchecked the last two boxes on your WAN interface page... "Block Private Networks" and "Block bogon networks" Gotta ask... ;)
-
Had just blocking of Bogons checked, so I unchecked it.
Blocking of local addresses was already UNCHECKED cause I know that with these DSL connections they're using local IPs so I wouldn't want that checked.
I turned on manual NAT out as you suggested and attached is a printscreen of what that looks like now.
I'm still having the same results.
-
My next step would be to verify that (say) a ping from LAN client computer to 8.8.8.8 was getting to the pfSense LAN interface. (Packet capture on the LAN interface, displaying just traffic to selected destination.)
If you don't see the traffic in the packet capture then I would look at the IP configuration of the client: Does it have the correct IP address for its default gateway? (Should be the IP address of the pfSense LAN interface.) Does it have the correct MAC address for that IP address?
-
Packet captured pings from laptop through the LAN interface (which all came back as "Request timed out." on my laptop) and this is what the capture looks like:
16:38:32.824386 00:1b:38:62:d0:1a (oui Unknown) > 54:04:a6:f3:2b:05 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 128, id 29038, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 117, length 40
16:38:37.490298 00:1b:38:62:d0:1a (oui Unknown) > 54:04:a6:f3:2b:05 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 128, id 29085, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 118, length 40
16:38:42.490628 00:1b:38:62:d0:1a (oui Unknown) > 54:04:a6:f3:2b:05 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 128, id 29122, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 119, length 40
16:38:47.490840 00:1b:38:62:d0:1a (oui Unknown) > 54:04:a6:f3:2b:05 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 128, id 29150, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 120, length 40As for the MAC addresses: I checked my arp tables on my laptop and all of the correct MAC addresses show as being associated with the correct IP addresses for both the WAN and LAN interfaces. So everything is good there.
-
So now with the same ping running, does a packet capture on the WAN interface show the ping leaving the pfSense box? If so, what is the source IP address?
-
Interface set to WAN, Host set to 8.8.8.8, Full detail, Reverse DNS Lookup turned OFF:
18:01:55.094629 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4003, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > 8.8.8.8: ICMP echo request, id 1, seq 133, length 40
18:01:59.796664 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4006, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > 8.8.8.8: ICMP echo request, id 1, seq 134, length 40
18:02:04.795955 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4009, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > 8.8.8.8: ICMP echo request, id 1, seq 135, length 40
18:02:09.795179 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4013, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > 8.8.8.8: ICMP echo request, id 1, seq 136, length 40Interface set to WAN, Host set to 8.8.8.8, Full detail, Reverse DNS Lookup turned ON:
18:03:26.746456 54:04:a6:f3:2b:07 (oui Unknown) > 00:26:62:1b:09:87 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4104, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 137, length 40
18:03:31.294265 54:04:a6:f3:2b:07 (oui Unknown) > 00:26:62:1b:09:87 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4109, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 138, length 40
18:03:36.293619 54:04:a6:f3:2b:07 (oui Unknown) > 00:26:62:1b:09:87 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4115, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 139, length 40
18:03:41.293819 54:04:a6:f3:2b:07 (oui Unknown) > 00:26:62:1b:09:87 (oui Unknown), ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 4118, offset 0, flags [none], proto ICMP (1), length 60)
192.168.168.100 > google-public-dns-a.google.com: ICMP echo request, id 1, seq 140, length 40192.168.168.100 is of course my laptop's IP address (where the pings are coming from).
-
I would really like to know where traffic is stopping inside pfSense. The above shows that it's tracking and trafficking my echo-requests…. but no echo-replies whatsoever. Just doesn't make sense.
Like check this out... INSIDE pfSense >> Diagnostics >> Ping: I set the interface to my WAN and tell it to ping 8.8.8.8 while I packet capture the WAN interface for the host address 192.168.168.2 (the WAN interface's ip address) and this is what I get:
18:29:04.862197 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 54046, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 3411, length 60
18:29:04.907335 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 54046, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 3411, length 60
18:29:05.862197 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 7269, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 3667, length 60
18:29:05.905440 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 7269, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 3667, length 60
18:29:06.862202 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 5674, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 3923, length 60
18:29:06.905499 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 5674, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 3923, length 60
18:29:07.862204 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 21147, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 4179, length 60
18:29:07.907530 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 21147, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 4179, length 60
18:29:08.069025 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 35388, offset 0, flags [none], proto ICMP (1), length 84)
192.168.2.2 > 8.8.8.8: ICMP echo request, id 22433, seq 0, length 64
18:29:08.199553 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 54, id 19673, offset 0, flags [none], proto ICMP (1), length 84)
8.8.8.8 > 192.168.2.2: ICMP echo reply, id 22433, seq 0, length 64
18:29:08.862208 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 50512, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 4435, length 60
18:29:08.909580 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 50512, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 4435, length 60
18:29:09.069780 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 3448, offset 0, flags [none], proto ICMP (1), length 84)
192.168.2.2 > 8.8.8.8: ICMP echo request, id 22433, seq 1, length 64
18:29:09.199595 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 54, id 19674, offset 0, flags [none], proto ICMP (1), length 84)
8.8.8.8 > 192.168.2.2: ICMP echo reply, id 22433, seq 1, length 64
18:29:09.862210 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 25233, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 4691, length 60
18:29:09.907438 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 25233, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 4691, length 60
18:29:10.070764 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 16652, offset 0, flags [none], proto ICMP (1), length 84)
192.168.2.2 > 8.8.8.8: ICMP echo request, id 22433, seq 2, length 64
18:29:10.199526 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 54, id 19675, offset 0, flags [none], proto ICMP (1), length 84)
8.8.8.8 > 192.168.2.2: ICMP echo reply, id 22433, seq 2, length 64
18:29:10.862211 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 35094, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 4947, length 60
18:29:10.907478 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 35094, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 4947, length 60
18:29:11.862212 54:04:a6:f3:2b:07 > 00:26:62:1b:09:87, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 64, id 36592, offset 0, flags [none], proto ICMP (1), length 80)
192.168.2.2 > 10.39.5.1: ICMP echo request, id 33034, seq 5203, length 60
18:29:11.905614 00:26:62:1b:09:87 > 54:04:a6:f3:2b:07, ethertype IPv4 (0x0800), length 94: (tos 0x0, ttl 126, id 36592, offset 0, flags [none], proto ICMP (1), length 80)
10.39.5.1 > 192.168.2.2: ICMP echo reply, id 33034, seq 5203, length 60So it's showing that when I tell the WAN to send off data, IT DOES and TRACKS IT! But if I try to send data THROUGH pfSense (from the LAN to the WAN) I get nothing. Just does not make sense.
-
You have turned off NAT in pfSense (at least for LAN to WAN traffic). If NAT was turned on the source address (as seen at the WAN interface) for the ping to 8.8.8.8 would be the pfSense WAN IP address.
I suspect your ADSL router doesn't have a route to the subnet of the pfSense LAN interface hence it doesn't know on which interface to forward packets with destinaion IP address 192.168.168.100.
You should turn NAT on in pfSense or add an appropriate route to your ADSL router.
-
Well, I've turned Dynamic Routing Version 2 ON in my DSL router.
And I renabled automatic NAT again in pfSense (since turning it to manual didn't make a difference).
Is there anything else I need to enable in pfSense in order for it to send RIP data back and forth between the two routers?
While I was remoted in to my laptop (using LogMeIn) I switched it back over to use the pfSense as it's default gateway and lost my connection and can't get it back (which I expected). So obviously traffic still isn't flowing through it. I'll have to continue work on this tomorrow morning since I'm at home now.
-
Can you put the modem in bridge mode and let the router do the login?
-
Thank you for any and all help in setting up my equipment. If setting my dsl router to bridge mode will simplify, speed up, make more stable or just all around better my connection I will be more than happy do it.
Now, please don't take this the wrong way as me being rude, I just want this post to get back on track… so I'll reiterate:
It's not my equipment that is the issue here.
I AM HAVING THE SAME PROBLEM WITH 1 DSL LINE WITH A ROUTER, 1 T1 LINE USING AN ADTRAN CSU/DSU, AND 1 T1 LINE USING A CISCO CSU/DSU TESTED WITH ANY AND ALL PORTS ON MY PFSENSE.ALL DO NOT WORK. ALL WITH THE SAME EXACT SYMPTONS.
It is NOT equipment OR how I've configured pfSense. I've had pfSense up and running perfectly fine countless times. It works great. The problem is that out of no where when I've reset states one too many times it breaks and NEVER COMES BACK... that is UNTIL I COMPLETELY REINSTALL PFSENSE. <<=== That is the issue. There is a bug somewhere. I want to know where and I want to know if there's a way to fix it without me having to re-install the entire program entirely. Because currently re-installation is the ONLY way I have been successful in getting pfSense to work properly again.
So again: I can't communicate THROUGH pfSense with ANY equipment I plug on the other side of it. Communication FROM pfSense itself works great! But THROUGH it doesn't. <<=== AND ALL OF THIS IS ONLY AFTER PFSENSE BREAKS. After I've had everything setup and working hunky-dory and then I tweak a few firewall rules, reset states one too many times and BAM! Broke and unreparable (unless someone can help me find the broken part and fix it).
Again, please don't take offense, I just want to keep my eye on the prize.
-
No worries- I guess I missed any mention of you resetting states to make this happen…. I did lose my glasses so need new ones...
But the DSL modem bridge comment... Im of the opinion that you shouldn't double NAT unless there is no other way... Bridge mode just keeps it simpler...
In my case- Ive reset states here quite often and guess Ill go back and read more about resetting states and see if I can reproduce it here...
Id be curious what your MBUF is at...
And how many states your machine maxes out at...