Pppoe multi ip problem with 2.0.1
-
Hi,
I want replace a Endian Firewall with Pfsense
I have a VDSL Line with 8 ip VTX (ISP) assign to the modem (Zyxel 2802 in Bridge-Mode) 212.x.45.166 and 212.x 46.83-94 are the used IP's = no ip is will be assigned (sometimes the icon of Interface is green but no IP adress is viewed in the Dashboard
I have also a second VDSL with 1 fixed IP (other Zyxel 2802 in Bridge) =this runs without problems in PfsenseI also have a VDSL Line at home with 1 fixed IP from VTX with no problem.
How must I configure PPPoE with multi IP?
Scenario
-
have you seen this
-
yes I have read this
but is a pppoe mit mutiple IP's a MLPPP Configuration?
Should I configure for each IP a PPPoe connection?in Endian I configure 1 pppoe per vdsl öline and assign the ip's ….
I think that the pppeo connection on the 8IP doesnt work
Internet -> Modem (Bridge) ->[WAN-Interface (PPPoE) 8IP-> PFsense1 -> LAN-Interface 192.168.1.1] -> Webserver1 (int:192.168.1.10)
-> Webserver2 (int:192.168.1.11)
Internet2-> Modem2 (Bridge) ->[WAN2-Interface (PPPoE 1IP -> PFsense1 -> LAN-Interface 192.168.1.1] -> Webserver3 (int: 192.168.1.13) -
I don't have pppoe environment by myself so i can't walk you throuh.
Can you with virtualIP's first and if it doesn't work straight then you might need more pppoe connections -
OK i try .. give response in 10/20 min
here are is snap from the ppp log
Jun 19 16:27:59
ppp: process 27351 started, version 5.5 (root@FreeBSD_8.0_pfSense_2.0-AMD64.snaps.pfsense.org 10:25 12-Oct-2011)Jun 19 16:27:59
ppp: web: web is not runningJun 19 16:27:59
ppp: [wan] Bundle: Interface ng0 createdJun 19 16:27:59
ppp: [wan_link0] Link: OPEN eventJun 19 16:27:59
ppp: [wan_link0] LCP: Open eventJun 19 16:27:59
ppp: [wan_link0] LCP: state change Initial –> StartingJun 19 16:27:59
ppp: [wan_link0] LCP: LayerStartJun 19 16:27:59
ppp: [wan_link0] PPPoE: Connecting to ''Jun 19 16:28:08
ppp: [wan_link0] PPPoE connection timeout after 9 secondsJun 19 16:28:08
ppp: [wan_link0] Link: DOWN eventJun 19 16:28:08
ppp: [wan_link0] LCP: Down eventJun 19 16:28:08
ppp: [wan_link0] Link: reconnection attempt 1 in 1 secondsJun 19 16:28:09
ppp: [wan_link0] Link: reconnection attempt 1Jun 19 16:28:09
ppp: [wan_link0] PPPoE: Connecting to ''Jun 19 16:28:18
ppp: [wan_link0] PPPoE connection timeout after 9 secondsJun 19 16:28:18
ppp: [wan_link0] Link: DOWN eventJun 19 16:28:18
ppp: [wan_link0] LCP: Down eventJun 19 16:28:18
ppp: [wan_link0] Link: reconnection attempt 2 in 4 seconds -
I think virtual IP work only when the ppp connection is up … but that is the problem .. it don't come up (Icon in Dashboard is green but Log say no!)
-
You need to use virtual IPs but keep just a single pppoe connection I believe.
There are quite a few posts about this.
An old post (2007!) but outlines the basics: http://forum.pfsense.org/index.php/topic,5253.0.htmlSteve
-
I read this article and add all IP to ARP in virtual IP
still the same
ppp log says LCP down an no Gatway is assigned
-
Hmm, I'm a bit confused, your ascii diagram is a bit mangled on my 1024*768 display.
So you have two pppoe connections on this box?
One 'GREEN' which is working OK and the other, VTX1, is not connecting, yes?I think you should remove all the virtual interfaces and try to get it connected with one IP first.
Steve
-
Sorry about the "confusion"
Yes "Green" is working … this is the 1 fixed IP line
VTX1 doesn't work (the 8 IP line).. the problem from VTX1 is it don't goes "up" fully ... it doesn't receive a IP
it also doesn't go up with 1 single IP when I only setup pppoe without GREEN and without virtual IPat home I have from the same ISP like VTX1 a 1 fixed IP line with pfsense 2.0.1 without problems
-
So what is different?
Possibly with one IP they send it to you via DHCP but with a group of IPs they are routing to you or you are required to set the IP statically.
This could be a question for your ISP.
Presumably it worked OK in Endian?Steve
-
In Endian it works well… I haven't defined all 8 IP's because I dont use it