WatchGuard x750e Hard drive install

Sacrilegious

Shall get the output later today. I just used the defaults then installing was that okay, could this be an issue with BIOS changes? shall I restore the defaults?

stephenw10

@Sacrilegious:

I did install the developers version, could that be the issue.

What exactly do you mean by this? Which image did you install from?

I suggested trying the Watchguard CF card because it definitely works. Most people use a CF card that is at least 1GB which will not boot by default. However since your substitute card is only 128MB it probably won't make much odds.

I'm just trying to find a dmesg from an X750 under 2.0.1. I'm sure I have one here somewhere…. ::)

Steve

Sacrilegious

What exactly do you mean by this? Which image did you install from?

I suggested trying the Watchguard CF card because it definitely works. Most people use a CF card that is at least 1GB which will not boot by default. However since your substitute card is only 128MB it probably won't make much odds.

I'm just trying to find a dmesg from an X750 under 2.0.1. I'm sure I have one here somewhere…. ::)

Steve

pfSense-2.0.1-RELEASE-i386. is the image I am using,

Ok I will have a go shortly with the WG CF just to rule it out,

Aswell as booting into verbose moode

stephenw10

Couldn't find it so I powered up my test box.
This is running the 2.0.1 Nano install from CF.
Here is last section of boot:

imecounter "TSC" frequency 1700067235 Hz quality 800
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ad0: 1911MB <sony 20071016="" ncfd2g=""> at ata0-master PIO4
ugen0.1: <intel> at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus0
ugen1.1: <intel> at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus1
ugen2.1: <intel> at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus2
ugen3.1: <intel> at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus3
ugen4.1: <intel> at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usbus4
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0</intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></sony>

Your log gets to exactly where it should be recognising ad0 and crashes.
Interestingly, but perhaps irrelevantly, my box finds all 5 USB buses before looking at subdevices. Yours does not. Do you have any USB devices somehow plugged in? You'd have to have soldered on a port to do it!
Complete boot log attached.

Steve

dmesg.boot.txt

Sacrilegious

Verbose output attached:

"ata0-master: pio=PIO2 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire"

This seems to be the culprit,

Any Ideas how i can kick its arse into gear?

[Pfsense Verbos boot.txt](/public/imported_attachments/1/Pfsense Verbos boot.txt)

Sacrilegious

Bios Settings

Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
+=====================================================+========================+
| Date (mm:dd:yy) Wed, Nov 28 2012;1m2012 Item Help |
| Time (hh:mm:ss) 17 : 40 : 6 |–----------------------|
| | Menu Level * |
| * IDE Channel 0 Master [128MB CHH] | |
| * IDE Channel 0 Slave [IC25N030ATMR04-0] | Press [Enter] to enter |
| | next page for detail |
| Video [EGA/VGA] | hard drive settings |
| Halt On [No Errors] | |
| | |
| Base Memory 640K | |
| Extended Memory 515072K | |
| Total Memory 516096K | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+=====================================================+========================+
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix - AwardBIOS CMOS Setup Utility
IDE Channel 0 Master
+=====================================================+========================+
| IDE HDD Auto-Detection [Press Enter] | Item Help |
| |–----------------------|
| IDE Channel 0 Master [Manual] | Menu Level ** |
| Access Mode [CHS] | |
| | To auto-detect the |
| Capacity 3750 MB | HDD's size, head… on |
| | this channel |
| Cylinder [58140] | |
| Head [ 2] | |
| Precomp [ 0] | |
| Landing Zone [58139] | |
| Sector [ 63] | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+=====================================================+========================+
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

+=====================================================+========================+
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Phoenix - AwardBIOS CMOS Setup Utility
IDE Channel 0 Slave
+=====================================================+========================+
| IDE HDD Auto-Detection [Press Enter] | Item Help |
| |–----------------------|
| IDE Channel 0 Slave [Auto] | Menu Level ** |
| Access Mode [Auto] | |
| | To auto-detect the |
| Capacity 30007 MB | HDD's size, head… on |
| | this channel |
| Cylinder 58140 | |
| Head 16 | |
| Precomp 0 | |
| Landing Zone 58139 | |
| Sector 63 | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+=====================================================+========================+
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
+=====================================================+========================+
| * CPU Feature [Press Enter] ^ | Item Help |
| * Hard Disk Boot Priority [Press Enter] |–----------------------|
| Virus Warning Disabled | Menu Level * |
| CPU L1 & L2 Cache Enabled | |
| Quick Power On Self Test [Enabled] | |
| First Boot Device [Hard Disk] | |
| Second Boot Device [Disabled] | |
| Third Boot Device [Disabled] | |
| Boot Other Device [Enabled] | |
| Boot Up NumLock Status [On] | |
| Gate A20 Option Fast | |
| Typematic Rate Setting Disabled | |
| x Typematic Rate (Chars/Sec) 6 | |
| x Typematic Delay (Msec) 250 | |
| Security Option Setup | |
| APIC Mode Enabled | |
| MPS Version Control For OS 1.4 | |
| OS Select For DRAM > 64MB [Non-OS2] | |
| Console Redirection Enabled V | |
+=====================================================+========================+
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

stephenw10

@Sacrilegious:

"ata0-master: pio=PIO2 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire"

I believe the CF card is the master on on the first IDE channel. It does not support UDMA, that's correct.
The HD should be set to slave, is it? I don't think this is the problem.

Steve

Edit: You posted while I was typing. So yes the above message simply reflects that the CF card doesn't support DMA. It's not a problem.

Edit: PS the quote box doesn't work, you have to use the code box to preserve formatting. ;)

stephenw10

Probably not relevant but with such a small CF card you should leave everything set to auto. Do not use CHS, heads=2.

Steve

Sacrilegious

One possible thing it may be,

during the installation i get :

"acd0: Failure - READ_BIG MEDIUM ERROR asc=0x11 etc etc etc. Could this be the issue, though it doesnt stop PFsense loading correctly on the Laptop

I did install the developers version, could that be the issue.

What exactly do you mean by this? Which image did you install from?

Going through the installation process

Configure console
I accept these settings

Tasks to perform
Quick / Easy install

This will install without asking any questions
OK

you may now wish to install a customer kernal configuration

Symetric Multiprocessing Kernal (more than on processor)
Embedded Kernel (No VGA Console Keyboard) No as nothing appears to happen and i cant get HTTP when doing 99 install
Developers Kernal (includes GDB etc) - i chose this

Sacrilegious

So Progress, well i think i have inserted the original CF and get a little bit further


ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0
ad0: 245MB <sandisk sdcfj-256="" hdx="" 4.06="">at ata0-master PIO4
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub0: 2 ports with 2 removable, self powered
ata0: DMA limited to UDMA33, controller found non-ATA66 cable
uhub1: 2 ports with 2 removable, self powered
ad1: 28615MB <ic25n030atmr04 0="" moaoad0a="">at ata0-slave UDMA33
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
GEOM: ad1s1: geometry does not match label (15h,63s != 16h,63s).
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
ROOT MOUNT ERROR:
If you have invalid mount options, reboot, and first try the following from
the loader prompt:

     set vfs.root.mountfrom.options=rw

and then remove invalid mount options from /etc/fstab.

Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input

mountroot></empty></fstype></device></device></fstype></ic25n030atmr04></intel></intel></sandisk></intel></intel></intel></intel>

note that this is keeping the Flash as Auto in the Bios

Sacrilegious

Just realised i truncated a fair bit of it


/boot.config: -D
Consoles: internal video/keyboard  serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 638kB/515072kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org, Mon Dec 12 17:10:52 EST 2011)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8a1d18 data=0x3c9e54+0x9b6a0 syms=[0x4+0x94100+0x4+0x                                                                                        caf47]
/

 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³          Welcome to pfSense!            ³
 ³                                         ³                 ______
 ³                                         ³                /      \
 ³  1\. Boot pfSense [default]              ³          _____/    f   \
 ³  2\. Boot pfSense with ACPI enabled      ³         /     \        /
 ³  3\. Boot pfSense using USB device       ³        /   p   \______/  Sense
 ³  4\. Boot pfSense in Safe Mode           ³        \       /      \
 ³  5\. Boot pfSense in single user mode    ³         \_____/        \
 ³  6\. Boot pfSense with verbose logging   ³               \        /
 ³  7\. Escape to loader prompt             ³                \______/
 ³  8\. Reboot                              ³
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³  Select option, [Enter] for default     ³
 ³  or [Space] to pause timer  -1          ³
 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p6 #0: Mon Dec 12 17:33:39 EST 2011
    root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/                                                                                        sys/pfSense_wrap.8.i386 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) M processor         1300MHz (1300.05-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Family = 6  Model = 9  Stepping = 5
  Features=0xa7e1fbbf <fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,   ="" pat,dts,acpi,mmx,fxsr,sse,sse2,tm,pbe="">real memory  = 528482304 (504 MB)
avail memory = 498069504 (474 MB)
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
MPTable: <oem00000 prod00000000="">ioapic0: Assuming intbase of 0
ioapic0 <version 2.0="">irqs 0-23 on motherboard
netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /bo                                                                                        ot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0710010, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /b                                                                                        oot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07100b0, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/l                                                                                        oader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc0883050, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw                                                                                        /.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in                                                                                         /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0710150, 0) error 1
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
pcib0: <mptable host-pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
vgapci0: <vga-compatible display="">port 0xea00-0xea07 mem 0xd0500000-0xd057ffff,0                                                                                        xc0000000-0xcfffffff,0xd0580000-0xd05bffff irq 16 at device 2.0 on pci0
pcib1: <mptable pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pci1: <pci bus="">on pcib1
mskc0: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x8000-0x80ff mem 0xd002000                                                                                        0-0xd0023fff irq 16 at device 0.0 on pci1
msk0: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc0
miibus0: <mii bus="">on msk0
e1000phy0: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc0: [ITHREAD]
pcib2: <mptable pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pci2: <pci bus="">on pcib2
mskc1: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x9000-0x90ff mem 0xd012000                                                                                        0-0xd0123fff irq 17 at device 0.0 on pci2
msk1: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc1
miibus1: <mii bus="">on msk1
e1000phy1: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus1
e1000phy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc1: [ITHREAD]
pcib3: <mptable pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pci3: <pci bus="">on pcib3
mskc2: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xa000-0xa0ff mem 0xd022000                                                                                        0-0xd0223fff irq 18 at device 0.0 on pci3
msk2: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc2
miibus2: <mii bus="">on msk2
e1000phy2: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus2
e1000phy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc2: [ITHREAD]
pcib4: <mptable pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pci4: <pci bus="">on pcib4
mskc3: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xb000-0xb0ff mem 0xd032000                                                                                        0-0xd0323fff irq 19 at device 0.0 on pci4
msk3: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc3
miibus3: <mii bus="">on msk3
e1000phy3: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus3
e1000phy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc3: [ITHREAD]
uhci0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">port 0xeb00-0xeb1f                                                                                         irq 23 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">on uhci0
uhci1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">port 0xed00-0xed1f                                                                                         irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">on uhci1
uhci2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">port 0xe800-0xe81f                                                                                         irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
usbus2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">on uhci2
uhci3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">port 0xe900-0xe91f                                                                                         irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
usbus3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">on uhci3
ehci0: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">mem 0xd05c0000-0xd05c03ff irq 2                                                                                        3 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">on ehci0
pcib5: <mptable pci-pci="" bridge="">at device 30.0 on pci0
pci5: <pci bus="">on pcib5
skc0: <marvell gigabit="" ethernet="">port 0xc000-0xc0ff mem 0xd042c000-0xd042ffff ir                                                                                        q 16 at device 0.0 on pci5
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0: <marvell semiconductor,="" inc.="" yukon="">on skc0
miibus4: <mii bus="">on sk0
e1000phy4: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus4
e1000phy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
skc0: [ITHREAD]
skc1: <marvell gigabit="" ethernet="">port 0xc400-0xc4ff mem 0xd0420000-0xd0423fff ir                                                                                        q 17 at device 1.0 on pci5
skc1: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk1: <marvell semiconductor,="" inc.="" yukon="">on skc1
miibus5: <mii bus="">on sk1
e1000phy5: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus5
e1000phy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
skc1: [ITHREAD]
skc2: <marvell gigabit="" ethernet="">port 0xc800-0xc8ff mem 0xd0424000-0xd0427fff ir                                                                                        q 18 at device 2.0 on pci5
skc2: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk2: <marvell semiconductor,="" inc.="" yukon="">on skc2
miibus6: <mii bus="">on sk2
e1000phy6: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus6
e1000phy6:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
skc2: [ITHREAD]
skc3: <marvell gigabit="" ethernet="">port 0xcc00-0xccff mem 0xd0428000-0xd042bfff ir                                                                                        q 19 at device 3.0 on pci5
skc3: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk3: <marvell semiconductor,="" inc.="" yukon="">on skc3
miibus7: <mii bus="">on sk3
e1000phy7: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus7
e1000phy7:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
skc3: [ITHREAD]
pci5: <encrypt decrypt,="" network="" computer="" crypto="">at device 4.0 (no driver attach                                                                                        ed)
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich6="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37                                                                                        6,0xf000-0xf00f at device 31.1 on pci0
ata0: <ata 0="" channel="">on atapci0
ata0: [ITHREAD]
ata1: <ata 1="" channel="">on atapci0
ata1: [ITHREAD]
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
cpu0 on motherboard
atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
unknown: <pnp0c01>can't assign resources (memory)
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501                                                                                         on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
ppc0: <standard parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77b irq 7 pnp                                                                                        id PNP0400 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <parallel port="" bus="">on ppc0
ppi0: <parallel i="" o="">on ppbus0
uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 pnpid PNP0501 on isa0
uart1: [FILTER]
orm0: <isa option="" rom="">at iomem 0xc0000-0xce7ff pnpid ORM0000 on isa0
unknown: <pnp0c01>can't assign resources (memory)
Timecounter "TSC" frequency 1300053575 Hz quality 800
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0

Fatal trap 18: integer divide fault while in kernel mode
cpuid = 0; apic id = 00
instruction pointer     = 0x20:0xc0bcdcab
stack pointer           = 0x28:0xc14208ac
frame pointer           = 0x28:0xc1420924
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 0 (swapper)
trap number             = 18
panic: integer divide fault
cpuid = 0
Uptime: 2s
Cannot dump. Device not defined or unavailable.
Automatic reboot in 15 seconds - press a key on the console to abort
--> Press a key on the console to reboot,
--> or switch off the system now.
/boot.config: -D
Consoles: internal video/keyboard  serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 638kB/515072kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org, Mon Dec 12 17:10:52 EST 2011)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8a1d18 data=0x3c9e54+0x9b6a0 syms=[0x4+0x94100+0x4+0x                                                                                        caf47]
/

 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³          Welcome to pfSense!            ³
 ³                                         ³                 ______
 ³                                         ³                /      \
 ³  1\. Boot pfSense [default]              ³          _____/    f   \
 ³  2\. Boot pfSense with ACPI enabled      ³         /     \        /
 ³  3\. Boot pfSense using USB device       ³        /   p   \______/  Sense
 ³  4\. Boot pfSense in Safe Mode           ³        \       /      \
 ³  5\. Boot pfSense in single user mode    ³         \_____/        \
 ³  6\. Boot pfSense with verbose logging   ³               \        /
 ³  7\. Escape to loader prompt             ³                \______/
 ³  8\. Reboot                              ³
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³  Select option, [Enter] for default     ³
 ³  or [Space] to pause timer  0           ³
 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p6 #0: Mon Dec 12 17:33:39 EST 2011
    root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/                                                                                        sys/pfSense_wrap.8.i386 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) M processor         1300MHz (1300.06-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Family = 6  Model = 9  Stepping = 5
  Features=0xa7e1fbbf <fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,   ="" pat,dts,acpi,mmx,fxsr,sse,sse2,tm,pbe="">real memory  = 528482304 (504 MB)
avail memory = 498069504 (474 MB)
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
MPTable: <oem00000 prod00000000="">ioapic0: Assuming intbase of 0
ioapic0 <version 2.0="">irqs 0-23 on motherboard
netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /bo                                                                                        ot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0710010, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /b                                                                                        oot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07100b0, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/l                                                                                        oader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc0883050, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw                                                                                        /.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in                                                                                         /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0710150, 0) error 1
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
pcib0: <mptable host-pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
vgapci0: <vga-compatible display="">port 0xea00-0xea07 mem 0xd0500000-0xd057ffff,0                                                                                        xc0000000-0xcfffffff,0xd0580000-0xd05bffff irq 16 at device 2.0 on pci0
pcib1: <mptable pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pci1: <pci bus="">on pcib1
mskc0: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x8000-0x80ff mem 0xd002000                                                                                        0-0xd0023fff irq 16 at device 0.0 on pci1
msk0: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc0
miibus0: <mii bus="">on msk0
e1000phy0: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc0: [ITHREAD]
pcib2: <mptable pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pci2: <pci bus="">on pcib2
mskc1: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x9000-0x90ff mem 0xd012000                                                                                        0-0xd0123fff irq 17 at device 0.0 on pci2
msk1: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc1
miibus1: <mii bus="">on msk1
e1000phy1: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus1
e1000phy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc1: [ITHREAD]
pcib3: <mptable pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pci3: <pci bus="">on pcib3
mskc2: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xa000-0xa0ff mem 0xd022000                                                                                        0-0xd0223fff irq 18 at device 0.0 on pci3
msk2: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc2
miibus2: <mii bus="">on msk2
e1000phy2: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus2
e1000phy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT                                                                                        -FDX, auto
mskc2: [ITHREAD]
pcib4: <mptable pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pci4: <pci bus="">on pcib4
mskc3: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xb000-0xb0ff mem 0xd032000                                                                                        0-0xd0323fff irq 19 at device 0.0 on pci4
msk3: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc3
miibus3: <mii bus="">on msk3
e1000phy3: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus3
e1000phy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mskc3: [ITHREAD]
uhci0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">port 0xeb00-0xeb1f irq 23 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">on uhci0
uhci1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">port 0xed00-0xed1f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">on uhci1
uhci2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">port 0xe800-0xe81f irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
usbus2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">on uhci2
uhci3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">port 0xe900-0xe91f irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
usbus3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">on uhci3
ehci0: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">mem 0xd05c0000-0xd05c03ff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">on ehci0
pcib5: <mptable pci-pci="" bridge="">at device 30.0 on pci0
pci5: <pci bus="">on pcib5
skc0: <marvell gigabit="" ethernet="">port 0xc000-0xc0ff mem 0xd042c000-0xd042ffff irq 16 at device 0.0 on pci5
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0: <marvell semiconductor,="" inc.="" yukon="">on skc0
miibus4: <mii bus="">on sk0
e1000phy4: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus4
e1000phy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc0: [ITHREAD]
skc1: <marvell gigabit="" ethernet="">port 0xc400-0xc4ff mem 0xd0420000-0xd0423fff irq 17 at device 1.0 on pci5
skc1: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk1: <marvell semiconductor,="" inc.="" yukon="">on skc1
miibus5: <mii bus="">on sk1
e1000phy5: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus5
e1000phy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc1: [ITHREAD]
skc2: <marvell gigabit="" ethernet="">port 0xc800-0xc8ff mem 0xd0424000-0xd0427fff irq 18 at device 2.0 on pci5
skc2: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk2: <marvell semiconductor,="" inc.="" yukon="">on skc2
miibus6: <mii bus="">on sk2
e1000phy6: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus6
e1000phy6:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc2: [ITHREAD]
skc3: <marvell gigabit="" ethernet="">port 0xcc00-0xccff mem 0xd0428000-0xd042bfff irq 19 at device 3.0 on pci5
skc3: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk3: <marvell semiconductor,="" inc.="" yukon="">on skc3
miibus7: <mii bus="">on sk3
e1000phy7: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus7
e1000phy7:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc3: [ITHREAD]
pci5: <encrypt decrypt,="" network="" computer="" crypto="">at device 4.0 (no driver attached)
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich6="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0
ata0: <ata 0="" channel="">on atapci0
ata0: [ITHREAD]
ata1: <ata 1="" channel="">on atapci0
ata1: [ITHREAD]
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
cpu0 on motherboard
atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
unknown: <pnp0c01>can't assign resources (memory)
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
ppc0: <standard parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77b irq 7 pnpid PNP0400 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <parallel port="" bus="">on ppc0
ppi0: <parallel i="" o="">on ppbus0
uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 pnpid PNP0501 on isa0
uart1: [FILTER]
orm0: <isa option="" rom="">at iomem 0xc0000-0xce7ff pnpid ORM0000 on isa0
unknown: <pnp0c01>can't assign resources (memory)
Timecounter "TSC" frequency 1300055338 Hz quality 800
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0
ad0: 245MB <sandisk sdcfj-256="" hdx="" 4.06="">at ata0-master PIO4
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub0: 2 ports with 2 removable, self powered
ata0: DMA limited to UDMA33, controller found non-ATA66 cable
uhub1: 2 ports with 2 removable, self powered
ad1: 28615MB <ic25n030atmr04 0="" moaoad0a="">at ata0-slave UDMA33
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
GEOM: ad1s1: geometry does not match label (15h,63s != 16h,63s).
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
ROOT MOUNT ERROR:
If you have invalid mount options, reboot, and first try the following from
the loader prompt:

     set vfs.root.mountfrom.options=rw

and then remove invalid mount options from /etc/fstab.

Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input</empty></fstype></device></device></fstype></ic25n030atmr04></intel></intel></sandisk></intel></intel></intel></intel></intel></intel></intel></intel></pnp0c01></isa></parallel></parallel></standard></pnp0c01></at></serial></ata></ata></intel></isa></pci-isa></encrypt></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></pci></mptable></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></vga-compatible></pci></mptable></software></version></oem00000></fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov, ></intel></intel></intel></intel></intel></intel></intel></intel></pnp0c01></isa></parallel></parallel></standard></pnp0c01></at></serial></ata></ata></intel></isa></pci-isa></encrypt></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></pci></mptable></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></vga-compatible></pci></mptable></software></version></oem00000></fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov, >

stephenw10

Ah Ha.
Ok so the reason it was crashing before is that the BIOS was reporting completely the wrong size/geometry for the CF card with H=2. Which is interesting in itself as you need to do this to boot from larger CF cards and usually FreeBSD just ignores the BIOS by that point and reads the geometry directly. :-
Anyway you're past that point now.
The mount root problem is because you installed pfSense in the laptop where the HD was connected as primary master (ad0). It's trying to mount it from there and failing. You need to tell it to mount from primary slave. At the mountroot> prompt type:

ufs:/dev/ad1s1a

It should then boot. When it has booted you then need to edit the fstab to make the change permanent.

Steve

rondonia

@stephenw10:

Ah Ha.
Ok so the reason it was crashing before is that the BIOS was reporting completely the wrong size/geometry for the CF card with H=2. Which is interesting in itself as you need to do this to boot from larger CF cards and usually FreeBSD just ignores the BIOS by that point and reads the geometry directly. :-
Anyway you're past that point now.
The mount root problem is because you installed pfSense in the laptop where the HD was connected as primary master (ad0). It's trying to mount it from there and failing. You need to tell it to mount from primary slave. At the mountroot> prompt type:
ufs:/dev/ad1s1a
It should then boot. When it has booted you then need to edit the fstab to make the change permanent.

Steve

I've beem reading this forum for almost a week and I have a similar problem as Sacrilegious, however I know my HDD address ad0, but is mounting.

Any help would be apreciated.

List of GEOM managed disk devices:
ad0
Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
<fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
eg. cd9660:/dev/acd0
This is equivalent to: mount -t cd9660 /dev/acd0 /

? List valid disk boot devices
<empty line="">Abort manual input

mountroot></empty></fstype></device></device></fstype>

wallabybob

At the mountroot> prompt why not try entering "?" (as suggested a few lines above the prompt) to see what bootable devices are present. It looks like the system has recognised the presence of ad0 and is attempting to mount ad0s1a as the root file system (

Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a

) but it is clearly not working!

A verbose boot (see my earlier reply for instructions) might give furthuer information about your problem.

Sacrilegious

As Requested:

ad1: setting UDMA33
ad1: 28615MB <ic25n030atmr04 0="" moaoad0a="">at ata0-slave UDMA33
ad1: 58605120 sectors [58140C/16H/63S] 16 sectors/interrupt 1 depth queue
ad1: Intel check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed

Rebooting...
/boot.config: -D
Consoles: internal video/keyboard  serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 638kB/515072kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org, Mon Dec 12 17:10:52 EST 2011)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8a1d18 data=0x3c9e54+0x9b6a0 syms=[0x4+0x94100+0x4+0xcaf47]
/

 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³          Welcome to pfSense!            ³
 ³                                         ³                 ______
 ³                                         ³                /      \
 ³  1\. Boot pfSense [default]              ³          _____/    f   \
 ³  2\. Boot pfSense with ACPI enabled      ³         /     \        /
 ³  3\. Boot pfSense using USB device       ³        /   p   \______/  Sense
 ³  4\. Boot pfSense in Safe Mode           ³        \       /      \
 ³  5\. Boot pfSense in single user mode    ³         \_____/        \
 ³  6\. Boot pfSense with verbose logging   ³               \        /
 ³  7\. Escape to loader prompt             ³                \______/
 ³  8\. Reboot                              ³
 ³                                         ³
 ³                                         ³
 ³                                         ³
 ³  Select option, [Enter] for default     ³
 ³  or [Space] to pause timer  1           ³
 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Type '?' for a list of commands, 'help' for more detailed help.
OK
OK 7
OK boot -v
SMAP type=01 base=0000000000000000 len=000000000009f800
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000ffb00000 len=0000000000500000
SMAP type=02 base=00000000e0000000 len=0000000010000000
SMAP type=02 base=000000000009f800 len=0000000000000800
SMAP type=01 base=0000000000100000 len=000000001f700000
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p6 #0: Mon Dec 12 17:33:39 EST 2011
    root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 i386
Preloaded elf kernel "/boot/kernel/kernel" at 0xc1269000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1300053505 Hz
CPU: Intel(R) Celeron(R) M processor         1300MHz (1300.05-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Family = 6  Model = 9  Stepping = 5
  Features=0xa7e1fbbf <fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,dts,acpi,mmx,fxsr,sse,sse2,tm,pbe>Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries
Data TLB: 4 KB Pages, 4-way set associative, 128 entries
Instruction TLB: 4 MB pages, fully associative, 2 entries
2nd-level cache: 512 KB, 4-way set associative, 64 byte line size
1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size
Data TLB: 4 MB Pages, 4-way set associative, 8 entries
1st-level data cache: 32 KB, 8-way set associative, 64 byte line size
real memory  = 528482304 (504 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001426000 - 0x000000001eeddfff, 497778688 bytes (121528 pages)
avail memory = 498069504 (474 MB)
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
MP Configuration Table version 1.4 found at 0xc00f0c00
APIC: Using the MPTable enumerator.
SMP: Added CPU 0 (BSP)
MPTable: <oem00000 prod00000000="">bios32: Found BIOS32 Service Directory header at 0xc00f9930
bios32: Entry = 0xf9f40 (c00f9f40)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x9f70
pnpbios: Found PnP BIOS data at 0xc00faa60
pnpbios: Entry = f0000:aa90  Rev = 1.0
Other BIOS signatures found:
ULE: setup cpu 0
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: Routing IRQ 0 -> intpin 2
lapic: Routing ExtINT -> LINT0
lapic: Routing NMI -> LINT1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
firmware: 'mxge_ethp_z8e' version 377876: 117102 bytes loaded at 0xc0f5d1e0
firmware: 'mxge_rss_eth_z8e' version 553468: 154580 bytes loaded at 0xc0f79be0
firmware: 'mxge_rss_ethp_z8e' version 563868: 155786 bytes loaded at 0xc0f9f840
firmware: 'iwn1000fw' version 0: 335056 bytes loaded at 0xc0d8ca30
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xc0dde778
wlan: mac acl policy registered
firmware: 'iwn5000fw' version 0: 353240 bytes loaded at 0xc0e0c634
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xc0e62a84
wlan: <802.11 Link Layer>
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xc0fc9070
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xc0fcb0e8
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xc0fcd160
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xc0fcf1d8
firmware: 'iwn6000fw' version 0: 462280 bytes loaded at 0xc0eb50f4
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0710010, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07100b0, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc0883050, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0710150, 0) error 1
firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xc0f28ca4
firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xc0f3ff80
firmware: 'mxge_eth_z8e' version 367564: 116477 bytes loaded at 0xc0f40a60
random: <entropy source,="" software,="" yarrow="">mem: <memory>Pentium Pro MTRR support enabled
nfslock: pseudo-device
crypto: <crypto core="">io: _null: <null device,="" zero="" device="">ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
npx0: INT 16 interface
cryptosoft0: <software crypto="">on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
padlock0: No ACE support.
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=25908086)
pcibios: BIOS version 3.00
PCIe: Memory Mapped configuration base @ 0xe0000000
pcib0: <mptable host-pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x2590, revid=0x04
        domain=0, bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2592, revid=0x04
        domain=0, bus=0, slot=2, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        map[10]: type Memory, range 32, base 0xd0500000, size 19, enabled
        map[14]: type I/O Port, range 32, base 0xea00, size  3, enabled
        map[18]: type Prefetchable Memory, range 32, base 0xc0000000, size 28, enabled
        map[1c]: type Memory, range 32, base 0xd0580000, size 18, enabled
pcib0: slot 2 INTA routed to irq 16
found-> vendor=0x8086, dev=0x2660, revid=0x04
        domain=0, bus=0, slot=28, func=0
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTA routed to irq 16
found-> vendor=0x8086, dev=0x2662, revid=0x04
        domain=0, bus=0, slot=28, func=1
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=12
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTB routed to irq 17
found-> vendor=0x8086, dev=0x2664, revid=0x04
        domain=0, bus=0, slot=28, func=2
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=5
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTC routed to irq 18
found-> vendor=0x8086, dev=0x2666, revid=0x04
        domain=0, bus=0, slot=28, func=3
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=10
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTD routed to irq 19
found-> vendor=0x8086, dev=0x2658, revid=0x04
        domain=0, bus=0, slot=29, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        map[20]: type I/O Port, range 32, base 0xeb00, size  5, enabled
pcib0: slot 29 INTA routed to irq 23
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xeb00
found-> vendor=0x8086, dev=0x2659, revid=0x04
        domain=0, bus=0, slot=29, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[20]: type I/O Port, range 32, base 0xed00, size  5, enabled
pcib0: slot 29 INTB routed to irq 19
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xed00
found-> vendor=0x8086, dev=0x265a, revid=0x04
        domain=0, bus=0, slot=29, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=5
        map[20]: type I/O Port, range 32, base 0xe800, size  5, enabled
pcib0: slot 29 INTC routed to irq 18
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe800
found-> vendor=0x8086, dev=0x265b, revid=0x04
        domain=0, bus=0, slot=29, func=3
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=11
        map[20]: type I/O Port, range 32, base 0xe900, size  5, enabled
pcib0: slot 29 INTD routed to irq 16
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe900
found-> vendor=0x8086, dev=0x265c, revid=0x04
        domain=0, bus=0, slot=29, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D3  current D0
        map[10]: type Memory, range 32, base 0xd05c0000, size 10, enabled
pcib0: slot 29 INTA routed to irq 23
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xd05c0000
found-> vendor=0x8086, dev=0x2448, revid=0xd4
        domain=0, bus=0, slot=30, func=0
        class=06-04-01, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2641, revid=0x04
        domain=0, bus=0, slot=31, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x266f, revid=0x04
        domain=0, bus=0, slot=31, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        map[20]: type I/O Port, range 32, base 0xf000, size  4, enabled
found-> vendor=0x8086, dev=0x266a, revid=0x04
        domain=0, bus=0, slot=31, func=3
        class=0c-05-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[20]: type I/O Port, range 32, base 0x500, size  5, port disabled
pcib0: slot 31 INTB routed to irq 19
vgapci0: <vga-compatible display="">port 0xea00-0xea07 mem 0xd0500000-0xd057ffff,0xc0000000-0xcfffffff,0xd0580000-0xd05bffff irq 16 at device 2.0 on pci0
pcib1: <mptable pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x8000-0x8fff
pcib1:   memory decode     0xd0000000-0xd00fffff
pcib1:   no prefetched decode
pci1: <pci bus="">on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=1, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0020000, size 14, enabled
pcib1: requested memory range 0xd0020000-0xd0023fff: good
        map[18]: type I/O Port, range 32, base 0x8000, size  8, enabled
pcib1: requested I/O range 0x8000-0x80ff: in range
pcib1: slot 0 INTA routed to irq 16
mskc0: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x8000-0x80ff mem 0xd0020000-0xd0023fff irq 16 at device 0.0 on pci1
mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0020000
mskc0: MSI count : 2
mskc0: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 48
mskc0: using IRQ 256 for MSI
mskc0: RAM buffer size : 48KB
mskc0: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc0: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk0: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc0
msk0: bpf attached
miibus0: <mii bus="">on msk0
e1000phy0: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mskc0: [MPSAFE]
mskc0: [ITHREAD]
pcib2: <mptable pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0x9000-0x9fff
pcib2:   memory decode     0xd0100000-0xd01fffff
pcib2:   no prefetched decode
pci2: <pci bus="">on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=2, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=12
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0120000, size 14, enabled
pcib2: requested memory range 0xd0120000-0xd0123fff: good
        map[18]: type I/O Port, range 32, base 0x9000, size  8, enabled
pcib2: requested I/O range 0x9000-0x90ff: in range
pcib2: slot 0 INTA routed to irq 17
mskc1: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x9000-0x90ff mem 0xd0120000-0xd0123fff irq 17 at device 0.0 on pci2
mskc1: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0120000
mskc1: MSI count : 2
mskc1: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 50
mskc1: using IRQ 257 for MSI
mskc1: RAM buffer size : 48KB
mskc1: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc1: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk1: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc1
msk1: bpf attached
miibus1: <mii bus="">on msk1
e1000phy1: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus1
e1000phy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mskc1: [MPSAFE]
mskc1: [ITHREAD]
pcib3: <mptable pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pcib3:   domain            0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0xa000-0xafff
pcib3:   memory decode     0xd0200000-0xd02fffff
pcib3:   no prefetched decode
pci3: <pci bus="">on pcib3
pci3: domain=0, physical bus=3
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=3, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0220000, size 14, enabled
pcib3: requested memory range 0xd0220000-0xd0223fff: good
        map[18]: type I/O Port, range 32, base 0xa000, size  8, enabled
pcib3: requested I/O range 0xa000-0xa0ff: in range
pcib3: slot 0 INTA routed to irq 18
mskc2: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xa000-0xa0ff mem 0xd0220000-0xd0223fff irq 18 at device 0.0 on pci3
mskc2: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0220000
mskc2: MSI count : 2
mskc2: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 258 to local APIC 0 vector 52
mskc2: using IRQ 258 for MSI
mskc2: RAM buffer size : 48KB
mskc2: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc2: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk2: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc2
msk2: bpf attached
miibus2: <mii bus="">on msk2
e1000phy2: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus2
e1000phy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mskc2: [MPSAFE]
mskc2: [ITHREAD]
pcib4: <mptable pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pcib4:   domain            0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xb000-0xbfff
pcib4:   memory decode     0xd0300000-0xd03fffff
pcib4:   no prefetched decode
pci4: <pci bus="">on pcib4
pci4: domain=0, physical bus=4
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=4, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0320000, size 14, enabled
pcib4: requested memory range 0xd0320000-0xd0323fff: good
        map[18]: type I/O Port, range 32, base 0xb000, size  8, enabled
pcib4: requested I/O range 0xb000-0xb0ff: in range
pcib4: slot 0 INTA routed to irq 19
mskc3: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xb000-0xb0ff mem 0xd0320000-0xd0323fff irq 19 at device 0.0 on pci4
mskc3: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0320000
mskc3: MSI count : 2
mskc3: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 259 to local APIC 0 vector 54
mskc3: using IRQ 259 for MSI
mskc3: RAM buffer size : 48KB
mskc3: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc3: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk3: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc3
msk3: bpf attached
miibus3: <mii bus="">on msk3
e1000phy3: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus3
e1000phy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mskc3: [MPSAFE]
mskc3: [ITHREAD]
uhci0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">port 0xeb00-0xeb1f irq 23 at device 29.0 on pci0
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 49
uhci0: [MPSAFE]
uhci0: [ITHREAD]
usbus0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">on uhci0
uhci1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">port 0xed00-0xed1f irq 19 at device 29.1 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 51
uhci1: [MPSAFE]
uhci1: [ITHREAD]
usbus1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">on uhci1
uhci2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">port 0xe800-0xe81f irq 18 at device 29.2 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 53
uhci2: [MPSAFE]
uhci2: [ITHREAD]
usbus2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">on uhci2
uhci3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">port 0xe900-0xe91f irq 16 at device 29.3 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 55
uhci3: [MPSAFE]
uhci3: [ITHREAD]
usbus3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">on uhci3
ehci0: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">mem 0xd05c0000-0xd05c03ff irq 23 at device 29.7 on pci0
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">on ehci0
pcib5: <mptable pci-pci="" bridge="">at device 30.0 on pci0
pcib5:   domain            0
pcib5:   secondary bus     5
pcib5:   subordinate bus   5
pcib5:   I/O decode        0xc000-0xdfff
pcib5:   memory decode     0xd0400000-0xd04fffff
pcib5:   no prefetched decode
pcib5:   Subtractively decoded bridge.
pci5: <pci bus="">on pcib5
pci5: domain=0, physical bus=5
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd042c000, size 14, enabled
pcib5: requested memory range 0xd042c000-0xd042ffff: good
        map[14]: type I/O Port, range 32, base 0xc000, size  8, enabled
pcib5: requested I/O range 0xc000-0xc0ff: in range
pcib5: slot 0 INTA routed to irq 16
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=1, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=12
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0420000, size 14, enabled
pcib5: requested memory range 0xd0420000-0xd0423fff: good
        map[14]: type I/O Port, range 32, base 0xc400, size  8, enabled
pcib5: requested I/O range 0xc400-0xc4ff: in range
pcib5: slot 1 INTA routed to irq 17
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=2, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0424000, size 14, enabled
pcib5: requested memory range 0xd0424000-0xd0427fff: good
        map[14]: type I/O Port, range 32, base 0xc800, size  8, enabled
pcib5: requested I/O range 0xc800-0xc8ff: in range
pcib5: slot 2 INTA routed to irq 18
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0428000, size 14, enabled
pcib5: requested memory range 0xd0428000-0xd042bfff: good
        map[14]: type I/O Port, range 32, base 0xcc00, size  8, enabled
pcib5: requested I/O range 0xcc00-0xccff: in range
pcib5: slot 3 INTA routed to irq 19
found-> vendor=0x177d, dev=0x0003, revid=0x00
        domain=0, bus=5, slot=4, func=0
        class=10-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x40 (16000 ns), maxlat=0x40 (16000 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type I/O Port, range 32, base 0xd000, size  8, enabled
pcib5: requested I/O range 0xd000-0xd0ff: in range
        map[18]: type I/O Port, range 32, base 0xd400, size  8, enabled
pcib5: requested I/O range 0xd400-0xd4ff: in range
pcib5: slot 4 INTA routed to irq 20
skc0: <marvell gigabit="" ethernet="">port 0xc000-0xc0ff mem 0xd042c000-0xd042ffff irq 16 at device 0.0 on pci5
skc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd042c000
skc0: interrupt moderation is 100 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc0: chip ver  = 0xb1
skc0: chip rev  = 0x09
skc0: SK_EPROM0 = 0x10
skc0: SRAM size = 0x010000
sk0: <marvell semiconductor,="" inc.="" yukon="">on skc0
sk0: bpf attached
miibus4: <mii bus="">on sk0
e1000phy4: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus4
e1000phy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc0: [MPSAFE]
skc0: [ITHREAD]
skc1: <marvell gigabit="" ethernet="">port 0xc400-0xc4ff mem 0xd0420000-0xd0423fff irq 17 at device 1.0 on pci5
skc1: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0420000
skc1: interrupt moderation is 100 us
skc1: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc1: chip ver  = 0xb1
skc1: chip rev  = 0x09
skc1: SK_EPROM0 = 0x10
skc1: SRAM size = 0x010000
sk1: <marvell semiconductor,="" inc.="" yukon="">on skc1
sk1: bpf attached
miibus5: <mii bus="">on sk1
e1000phy5: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus5
e1000phy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 56
skc1: [MPSAFE]
skc1: [ITHREAD]
skc2: <marvell gigabit="" ethernet="">port 0xc800-0xc8ff mem 0xd0424000-0xd0427fff irq 18 at device 2.0 on pci5
skc2: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0424000
skc2: interrupt moderation is 100 us
skc2: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc2: chip ver  = 0xb1
skc2: chip rev  = 0x09
skc2: SK_EPROM0 = 0x10
skc2: SRAM size = 0x010000
sk2: <marvell semiconductor,="" inc.="" yukon="">on skc2
sk2: bpf attached
miibus6: <mii bus="">on sk2
e1000phy6: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus6
e1000phy6:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc2: [MPSAFE]
skc2: [ITHREAD]
skc3: <marvell gigabit="" ethernet="">port 0xcc00-0xccff mem 0xd0428000-0xd042bfff irq 19 at device 3.0 on pci5
skc3: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0428000
skc3: interrupt moderation is 100 us
skc3: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc3: chip ver  = 0xb1
skc3: chip rev  = 0x09
skc3: SK_EPROM0 = 0x10
skc3: SRAM size = 0x010000
sk3: <marvell semiconductor,="" inc.="" yukon="">on skc3
sk3: bpf attached
miibus7: <mii bus="">on sk3
e1000phy7: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus7
e1000phy7:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
skc3: [MPSAFE]
skc3: [ITHREAD]
pci5: <encrypt decrypt,="" network="" computer="" crypto="">at device 4.0 (no driver attached)
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich6="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: <ata 0="" channel="">on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 57
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ata 1="" channel="">on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 58
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
cpu0 on motherboard
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
pnpbios: 14 devices, largest 92 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000
pnpbios: handle 7 device ID INT0800 (0008d425)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000
PNP0c01: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000
pnpbios: handle 8 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c02: adding fixed memory32 range 0xce800-0xcffff, size=0x1800
pnpbios: handle 9 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x294-0x297, size=0x4, align=0
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x400-0x4bf, size=0xc0, align=0
pnpbios: handle 10 device ID PNP0a03 (030ad041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 12 device ID PNP0501 (0105d041)
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
PNP0400: adding io range 0x778-0x77b, size=0x4, align=0
pnpbios: handle 13 device ID PNP0400 (0004d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 15 device ID PNP0501 (0105d041)
isa_probe_children: disabling PnP devices
atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
unknown: <at real="" time="" clock="">failed to probe at port 0x60,0x64 irq 1 pnpid PNP0303 on isa0
unknown: <at real="" time="" clock="">failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <at real="" time="" clock="">failed to probe at iomem 0xffb80000-0xffbfffff pnpid INT0800 on isa0
unknown: <pnp0c01>can't assign resources (memory)
unknown: <pnp0c01>at iomem 0-0x9ffff pnpid PNP0c01 on isa0
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501 on isa0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 59
uart0: [FILTER]
uart0: fast interrupt
uart0: console (9600,n,8,1)
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <standard parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77b irq 7 pnpid PNP0400 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 60
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <parallel port="" bus="">on ppc0
ppi0: <parallel i="" o="">on ppbus0
uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 pnpid PNP0501 on isa0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 61
uart1: [FILTER]
uart1: fast interrupt
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <isa option="" rom="">at iomem 0xc0000-0xce7ff pnpid ORM0000 on isa0
atkbdc0 failed to probe at port 0x60 on isa0
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
sc0 failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <pnp0c01>can't assign resources (memory)
unknown: <pnp0c01>at iomem 0-0x9ffff pnpid PNP0c01 on isa0
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 50002060 Hz
Timecounter "TSC" frequency 1300053505 Hz quality 800
Timecounters tick every 10.000 msec
vlan: initialized, using hash tables with chaining
crypto: <crypto device="">IPsec: Initialized Security Association Processing.
pflog0: bpf attached
lo0: bpf attached
pfsync0: bpf attached
enc0: bpf attached
ata0: Identifying devices: 00000003
ata0: New devices: 00000003
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub0: 2 ports with 2 removable, self powered
ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire
uhub1: 2 ports with 2 removable, self powered
ad0: setting PIO4
ad0: 245MB <sandisk sdcfj-256="" hdx="" 4.06="">at ata0-master PIO4
ad0: 501760 sectors [980C/16H/32S] 4 sectors/interrupt 1 depth queue
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
ad0: Intel check1 failed
GEOM: new disk ad0
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata0: DMA limited to UDMA33, controller found non-ATA66 cable
ad1: setting UDMA33
ad1: 28615MB <ic25n030atmr04 0="" moaoad0a="">at ata0-slave UDMA33
ad1: 58605120 sectors [58140C/16H/63S] 16 sectors/interrupt 1 depth queue
ad1: Intel check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ATA PseudoRAID loaded
GEOM: new disk ad1
GEOM: ad1s1: geometry does not match label (15h,63s != 16h,63s).
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
ROOT MOUNT ERROR:
If you have invalid mount options, reboot, and first try the following from
the loader prompt:

     set vfs.root.mountfrom.options=rw

and then remove invalid mount options from /etc/fstab.

Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input

mountroot> ?

List of GEOM managed disk devices:
  ufsid/50b4cee13a7e71f6 ad1s1b ad1s1a ad1s1 ad1 ad0s8 ad0s7 ad0s6 ad0s5 ad0s4 ad0s3 ad0s2 ad0s1 ad0
Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input

mountroot></empty></fstype></device></device></fstype></empty></fstype></device></device></fstype></ic25n030atmr04></sandisk></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></crypto></pnp0c01></pnp0c01></isa></parallel></parallel></standard></pnp0c01></pnp0c01></at></at></at></at></serial></ata></ata></intel></isa></pci-isa></encrypt></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></pci></mptable></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></vga-compatible></pci></mptable></software></null>_</crypto></memory></entropy></version></oem00000></fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,dts,acpi,mmx,fxsr,sse,sse2,tm,pbe> 
``` _Regards Neil_</ic25n030atmr04>

stephenw10

Did you try my suggestion?: ufs:/dev/ad1s1a

Steve

Sacrilegious

Indeed


mountroot> ufs:/dev/ad1s1a
Trying to mount root from ufs:/dev/ad1s1a
Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input
t
mountroot>t</empty></fstype></device></device></fstype>

However no success as of yet :'(

So what next batman?

Neil

stephenw10

Hmm, well try ad1s1b since that's the only other likely thing listed.
Otherwise it's back to bat cave for testing! ;)

Steve

Sacrilegious

I take it this is the root cause,

ad0: Intel check1 failed
GEOM: new disk ad0
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata0: DMA limited to UDMA33, controller found non-ATA66 cable
ad1: setting UDMA33
ad1: 28615MB <ic25n030atmr04 0="" moaoad0a="">at ata0-slave UDMA33
ad1: 58605120 sectors [58140C/16H/63S] 16 sectors/interrupt 1 depth queue
ad1: Intel check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ata1: Identifying devices: 00000000
ata1: New devices: 00000000</ic25n030atmr04>

stephenw10

No I don't think so though info on that seems to be sparse. I think that's just FreeBSD checking for specific hardware that would require some sort of quirky handling. If you remove verbose boot logging I imagine that would not appear.
Does your harddrive have it's real geometry written on it? Does it agree with either the BIOS or the pfSesne boot log?

I.e. The cause is more likely:


ad1: 58605120 sectors [58140C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad1
GEOM: ad1s1: geometry does not match label (15h,63s != 16h,63s).

So it is having a problem mounting ad1s1 (a or b)

Steve