Bridge LAN + WLAN not working in last snapshot

[eri--]

Can you paste those errors here.

[MaxPF]

This is from a backup that used to work:

 <interfaces><wan><enable><if>vr1</if>
			<ipaddr>dhcp</ipaddr>
			 <gateway><blockpriv>on</blockpriv>
			<blockbogons>on</blockbogons>
			 <media><mediaopt></mediaopt></media></gateway></enable></wan> 
		 <lan><enable><if>bridge0</if>

			<ipaddr>192.168.1.1</ipaddr>
			<subnet>24</subnet>
			 <spoofmac></spoofmac></enable></lan> 
		 <opt1><if>vr2</if>

			 <spoofmac><enable><ipaddr>10.10.10.1</ipaddr>
			<subnet>24</subnet></enable></spoofmac></opt1> 
		 <opt2><if>vr0</if>
			 <enable><spoofmac></spoofmac></enable></opt2> 
		 <opt3><if>run0</if>
			 <wireless><standard>11g</standard>
				<mode>hostap</mode>
				<protmode>off</protmode>
				<ssid>LHC</ssid>
				<channel>0</channel>
				 <authmode><txpower>99</txpower>
				 <distance><regdomain><regcountry><reglocation><wpa><macaddr_acl><auth_algs>1</auth_algs>
					<wpa_mode>2</wpa_mode>
					<wpa_key_mgmt>WPA-PSK</wpa_key_mgmt>
					<wpa_pairwise>CCMP</wpa_pairwise>
					<wpa_group_rekey>120</wpa_group_rekey>
					<wpa_gmk_rekey>3600</wpa_gmk_rekey>
					<passphrase></passphrase>
					 <ext_wpa_sw><ieee8021x><enable></enable></ieee8021x></ext_wpa_sw></macaddr_acl></wpa> 
				 <auth_server_addr><auth_server_port><auth_server_shared_secret><wme><pureg><enable></enable></pureg> 
				 <auth_server_addr2><auth_server_port2><auth_server_shared_secret2></auth_server_shared_secret2></auth_server_port2></auth_server_addr2></wme></auth_server_shared_secret></auth_server_port></auth_server_addr></reglocation></regcountry></regdomain></distance></authmode></wireless> 
			 <enable><spoofmac></spoofmac></enable></opt3></interfaces> 

	 <bridges><bridged><members>opt2,opt3</members>

			 <maxaddr><timeout><maxage><fwdelay><hellotime><priority><proto>rstp</proto>
			 <holdcount><ifpriority><ifpathcost><bridgeif>bridge0</bridgeif></ifpathcost></ifpriority></holdcount></priority></hellotime></fwdelay></maxage></timeout></maxaddr></bridged></bridges> 

[xbipin]

@ermal:

Can you paste those errors here.

i simply submitted that and then it deleted the crash report after which i reverted to the previous working snapshot. u would be having access to the place where this crash report got submitted i guess

[MaxPF]

Just tried the Jan 24 07:37:42 build, but same thing is happening. I found a workaround that maybe can help troubleshoot this issue.

After restoring my backup and rebooting I have this setup for the interface:

WAN (wan)       -> vr1        -> v4/DHCP4: XX.XX.XX.161/23
BRIDGE (lan)    -> bridge0    -> v4: 192.168.1.1/24
GUEST (opt1)    -> vr2        -> v4: 10.10.10.1/24
LAN (opt2)      -> vr0        ->
WLAN (opt3)     -> run0_wlan0 ->

with OPT2 and OPT3 bridged in bridge0 and nothing is working. However if in the serial console I choose option #2 and assign an IP address to LAN (opt2) like this:

WAN (wan)       -> vr1        -> v4/DHCP4: XX.XX.XX.161/23
BRIDGE (lan)    -> bridge0    -> v4: 192.168.1.1/24
GUEST (opt1)    -> vr2        -> v4: 10.10.10.1/24
LAN (opt2)      -> vr0        -> v4: 192.168.1.2/24
WLAN (opt3)     -> run0_wlan0 ->

then everything starts working again!

UPDATE:
Not sure what happened overnight, but this morning it didn't work again (it was fine yesterday evening after the workaround) so I had to do another factory reset.

[t3h0th3r]

+1

[zetar]

Hello
I too have the same problem.
Until the version built on Tue Jan 22 17:56:08 EST 2013
Everything works fine, no longer works after the bridge.
My setup only bridge Wan-Lan Ip Wan With the gateway.
Use public IP, I do not need it use the NAT only firewall packet filtering, it will not work the Traffic Shaper.
Thank you.

[eri--]

Please try the next snapshot coming out.

[zetar]

I tried that today, but it's still not try the next one.

[MaxPF]

Just tried build Jan 25 11:42:18 and it is still the same with bridged interfaces not working at all.

[xbipin]

still doesnt work but i guess its something to do with dhcp and the bridge as my wireless devices remain on obtaining ip address but never gets one

[zetar]

I use manual IP addresses but should not be the same, I have changed something.

[MaxPF]

@xbipin:

still doesnt work but i guess its something to do with dhcp and the bridge as my wireless devices remain on obtaining ip address but never gets one

No it's not just dhcp that breaks. Even with static ip's nothing works with bridges interfaces.

[eri--]

I think i found the issues.
Please try tomorrows snapshot.

[MaxPF]

Great! I will and report back.
Is this the fix https://github.com/bsdperimeter/pfsense/commit/19defb88d4c7ff7e097b32702dee6e9b948e46b6?

[xbipin]

no luck for me as yet, i guess there were few more patches so will try the snap after that

[xbipin]

27th snap solved it

[MaxPF]

I can also confirm that Jan 27 build fixed the problem. Well done!

[eri--]

Thank you for testing.
Strange this was not hit before!

[zetar]

thanks will install that version and will refer.

[zetar]

Jan 27 20:37:59 EST 2013
Is Works Ok.
Thanks.