Watchguard Timeouts

svensol

Hi,

I'm running the latest build of 2.1 (2.1-RC1 (i386) built on Fri Aug 30 13:39:25 EDT 2013) on my Watchguard x750 an whenever I start playing YouTube videos via my iPhone or iPad, my LAN port times out.

It's not 100% every time, but 8 or 9 times out of 10.

Aug 31 08:07:44 pfsense kernel: re1: watchdog timeout
Aug 31 08:07:44 pfsense kernel: re1: link state changed to DOWN
Aug 31 08:07:44 pfsense kernel: re1_vlan100: link state changed to DOWN
Aug 31 08:07:44 pfsense check_reload_status: Linkup starting re1
Aug 31 08:07:44 pfsense check_reload_status: Linkup starting re1_vlan100
Aug 31 08:07:46 pfsense check_reload_status: Linkup starting re1
Aug 31 08:07:46 pfsense kernel: re1: link state changed to UP
Aug 31 08:07:46 pfsense kernel: re1_vlan100: link state changed to UP
Aug 31 08:07:46 pfsense check_reload_status: Linkup starting re1_vlan100
Aug 31 08:07:48 pfsense php: rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (192.168.0.254 2001:470:xxx:xx::1)
Aug 31 08:07:48 pfsense php: rc.linkup: DEVD Ethernet detached event for opt3
Aug 31 08:07:50 pfsense php: rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (192.168.0.254 2001:470:xxx:xx::1)
Aug 31 08:07:50 pfsense check_reload_status: rc.newwanip starting re1
Aug 31 08:07:50 pfsense php: rc.linkup: DEVD Ethernet attached event for opt3
Aug 31 08:07:50 pfsense php: rc.linkup: HOTPLUG: Configuring interface opt3
Aug 31 08:07:50 pfsense php: rc.linkup: The command '/sbin/ifconfig 're1_vlan100' inet  delete' returned exit code '1', the output was 'ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address' 
Aug 31 08:07:52 pfsense dhcpleases: Could not deliver signal HUP to process because its pidfile does not exist, No such process.
Aug 31 08:07:53 pfsense php: rc.newwanip: rc.newwanip: Informational is starting re1.
Aug 31 08:07:53 pfsense php: rc.newwanip: rc.newwanip: on (IP address: 192.168.0.254) (interface: lan) (real interface: re1).
Aug 31 08:07:54 pfsense check_reload_status: Reloading filter
Aug 31 08:07:55 pfsense check_reload_status: updating dyndns opt3

Other than the stock install I have:

IPv6 via he.net
Snort (enabled or disabled, makes no difference)
VLAN100 on the LAN port, but nothing using it

I did read the http://doc.pfsense.org/index.php/PfSense_on_Watchguard_Firebox about the timeouts so I've tried disabling the

Hardware Checksum Offloading
Hardware TCP Segmentation Offloading
Hardware Large Receive Offloading

but they've made no difference.

The Watchguard is plugged into an Airport Extreme which is also acting as the access point, so I'm eliminating as many extra interfaces and devices as possible.

This is happening a lot more recently, I'm don't remember it happening anywhere near as much on the 2.0.x series. Have there been some fundamental changes to the driver?

Any pointers appreciated.

Cheers,

Sven

stephenw10

I assume you mean the X700? The X750e doesn't have any re interfaces.

Steve

svensol

Sorry - yes..

x700

stephenw10

There hasn't been any progress on the re(4) timeouts as far as I know I'm afraid.
As you may have read it seems very dependent on what you have it connected to. You could try putting a switch between your Airport and the Watchguard box as a test.

Steve