• Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Search
  • Register
  • Login
Netgate Discussion Forum
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Search
  • Register
  • Login

Watchguard Timeouts

Scheduled Pinned Locked Moved 2.1 Snapshot Feedback and Problems - RETIRED
4 Posts 2 Posters 2.8k Views
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • S
    svensol
    last edited by Aug 31, 2013, 8:47 AM

    Hi,

    I'm running the latest build of 2.1 (2.1-RC1 (i386) built on Fri Aug 30 13:39:25 EDT 2013) on my Watchguard x750 an whenever I start playing YouTube videos via my iPhone or iPad, my LAN port times out.

    It's not 100% every time, but 8 or 9 times out of 10.

    Aug 31 08:07:44 pfsense kernel: re1: watchdog timeout
    Aug 31 08:07:44 pfsense kernel: re1: link state changed to DOWN
    Aug 31 08:07:44 pfsense kernel: re1_vlan100: link state changed to DOWN
    Aug 31 08:07:44 pfsense check_reload_status: Linkup starting re1
    Aug 31 08:07:44 pfsense check_reload_status: Linkup starting re1_vlan100
    Aug 31 08:07:46 pfsense check_reload_status: Linkup starting re1
    Aug 31 08:07:46 pfsense kernel: re1: link state changed to UP
    Aug 31 08:07:46 pfsense kernel: re1_vlan100: link state changed to UP
    Aug 31 08:07:46 pfsense check_reload_status: Linkup starting re1_vlan100
    Aug 31 08:07:48 pfsense php: rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (192.168.0.254 2001:470:xxx:xx::1)
    Aug 31 08:07:48 pfsense php: rc.linkup: DEVD Ethernet detached event for opt3
    Aug 31 08:07:50 pfsense php: rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (192.168.0.254 2001:470:xxx:xx::1)
    Aug 31 08:07:50 pfsense check_reload_status: rc.newwanip starting re1
    Aug 31 08:07:50 pfsense php: rc.linkup: DEVD Ethernet attached event for opt3
    Aug 31 08:07:50 pfsense php: rc.linkup: HOTPLUG: Configuring interface opt3
    Aug 31 08:07:50 pfsense php: rc.linkup: The command '/sbin/ifconfig 're1_vlan100' inet  delete' returned exit code '1', the output was 'ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address' 
    Aug 31 08:07:52 pfsense dhcpleases: Could not deliver signal HUP to process because its pidfile does not exist, No such process.
    Aug 31 08:07:53 pfsense php: rc.newwanip: rc.newwanip: Informational is starting re1.
    Aug 31 08:07:53 pfsense php: rc.newwanip: rc.newwanip: on (IP address: 192.168.0.254) (interface: lan) (real interface: re1).
    Aug 31 08:07:54 pfsense check_reload_status: Reloading filter
    Aug 31 08:07:55 pfsense check_reload_status: updating dyndns opt3
    
    

    Other than the stock install I have:

    • IPv6 via he.net
    • Snort (enabled or disabled, makes no difference)
    • VLAN100 on the LAN port, but nothing using it

    I did read the http://doc.pfsense.org/index.php/PfSense_on_Watchguard_Firebox about the timeouts so I've tried disabling the

    • Hardware Checksum Offloading
    • Hardware TCP Segmentation Offloading
    • Hardware Large Receive Offloading

    but they've made no difference.

    The Watchguard is plugged into an Airport Extreme which is also acting as the access point, so I'm eliminating as many extra interfaces and devices as possible.

    This is happening a lot more recently, I'm don't remember it happening anywhere near as much on the 2.0.x series. Have there been some fundamental changes to the driver?

    Any pointers appreciated.

    Cheers,

    Sven

    1 Reply Last reply Reply Quote 0
    • S
      stephenw10 Netgate Administrator
      last edited by Aug 31, 2013, 4:39 PM

      I assume you mean the X700? The X750e doesn't have any re interfaces.

      Steve

      1 Reply Last reply Reply Quote 0
      • S
        svensol
        last edited by Sep 2, 2013, 10:23 AM

        Sorry - yes..

        x700

        1 Reply Last reply Reply Quote 0
        • S
          stephenw10 Netgate Administrator
          last edited by Sep 2, 2013, 2:14 PM

          There hasn't been any progress on the re(4) timeouts as far as I know I'm afraid.
          As you may have read it seems very dependent on what you have it connected to. You could try putting a switch between your Airport and the Watchguard box as a test.

          Steve

          1 Reply Last reply Reply Quote 0
          4 out of 4
          • First post
            4/4
            Last post
          Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.
            This community forum collects and processes your personal information.
            consent.not_received