Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Pfsense 2.0.3 stuck on reboot with X550e

    Scheduled Pinned Locked Moved Hardware
    17 Posts 2 Posters 3.8k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • H
      harveje
      last edited by

      Thanks,
      Flashed B7 and set Acpi to enable in bios
      reboot command
      different tone then before
      still no reboot  stuck on rebooting in console and shutting down on lcd
      4 of the 6 led's (2 thru 5)on pc board are slow flashing 1 and 6 are not lit
      I've spent many hrs on here reading on installing, troubleshooting etc, and tried a few things but no dice.

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        If you mean the internal diagnostic LEDs next to the SuperIO chip (near the PSU connector) there are 8 on every box I've looked in. If they are not all lit and steady then the box isn't passing the initial hardware testing that's part of the bios code. If that's true there should be some output on the serial console at 115200bps, unless you've changed it. It may be hanging before the serial redirect code kicks in in which case you'd see nothing. Unfortunately the diagnostic LEDs are completely undocumented.
        Either way it's hard to imagine something that passes a cold boot but not a warm boot.  :-\ Definitely check the battery.

        You never said if it gets to the lower fan speed setting?

        Steve

        1 Reply Last reply Reply Quote 0
        • H
          harveje
          last edited by

          @stephenw10:

          If you mean the internal diagnostic LEDs next to the SuperIO chip (near the PSU connector) there are 8 on every box I've looked in. If they are not all lit and steady then the box isn't passing the initial hardware testing that's part of the bios code. If that's true there should be some output on the serial console at 115200bps, unless you've changed it. It may be hanging before the serial redirect code kicks in in which case you'd see nothing. Unfortunately the diagnostic LEDs are completely undocumented.
          Either way it's hard to imagine something that passes a cold boot but not a warm boot.  :-\ Definitely check the battery.

          You never said if it gets to the lower fan speed setting?

          Steve

          When trying to reboot the mb led's are slowly flashing, when running they are solid
          Checked batt and it was 2.73V so I'm looking for another
          fans are in low speed while unit is running
          when trying to reboot they go back to high and stay there till power off

          Thank you for helping– I'm just at a loss right now..

          1 Reply Last reply Reply Quote 0
          • H
            harveje
            last edited by

            Put diff battery in, re checked bios for setup
            booted into pfsense
            tried reboot and still hangs

            enabled acpi in bios
            booted
            tried and hangs

            booted into pf
            entered sysctl hw.acpi.disable_on_reboot=1 in command line
            rebooted
            hangs

            during the attempted reboot there is no data on the console for 115200  only on boot up
            on 9600 pf looks to be shutting down and says rebooting and hangs.

            I'm at a loss

            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by

              Hmm, I'm at a loss too.  :-
              Clearly it's not making it past the bios self test code. I cannot imagine what might pass a cold boot but fail a warm boot. It seems very unlikely to be anything to do with pfSense though.
              How much RAM do you have in there? With 2GB the memory check can take a long time.

              I would usually suggest reseating the RAM and CPU. I have a hard time believing it's that but it worth a try.

              Steve

              1 Reply Last reply Reply Quote 0
              • H
                harveje
                last edited by

                Thanks Steve,
                I've reseated the CPU, ram, etc.. only have 7xxmb ram and tried each one individually, tried different bios acpi settings, tried disabling items in bios, new battery, different bios flashes, different pfsense nano versions, bios pin reset, front push button reset  etc.. Still will not do a reboot.
                It acts like it's hanging at the starting stages of the bios with the fans going back to 100%  I really like the unit but I need it to reboot when commanded. I've switched baud rates trying to find or see error coded but nothing
                Any other thoughts? sledge hammer?  ;D

                Thanks

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  Have you swapped out the CPU? Are you still using the original Celeron-M?
                  If you have did you correctly switch both sets of DIP switches?

                  Other than that I'm out of ideas. I can't think what would stop it warm booting. Perhaps some Googling for that general fault.  :-\

                  Steve

                  1 Reply Last reply Reply Quote 0
                  • H
                    harveje
                    last edited by

                    I did not swap the cpu out, just reseated it, but I'll check the dips.  I've googled till i'm googly  but will keep searching..
                    Thanks

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      The power supply is a likely suspect. I had a box with a dead PSU, completely dead though. It's standard ATX so you can easily use any PSU to test. Could be a power problem on the board. Do any of the capacitors look cooked? (bulging/leaking).

                      Steve

                      1 Reply Last reply Reply Quote 0
                      • H
                        harveje
                        last edited by

                        replaced ps and still no reboot.
                        checked dips and they are set on Banias
                        IS the Jp_hmw1 suppose to have a shunt?

                        Thanks

                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          Nope, nothing on JP_HWM1. No idea what it does.

                          Steve

                          1 Reply Last reply Reply Quote 0
                          • H
                            harveje
                            last edited by

                            ding, ding….
                            using the hault command in either the gui or putty will trigger a reboot... Now what's up with those apples??? :o :o

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              Hmm.  ;)
                              The box can't shutdown correctly because it doesn't have an ATX compliant PSU, it's always on, it has a real power switch. Thus when you try to shutdown it can't so some boxes just halt and others reboot.
                              I'm going to have to test my box here to be sure.

                              Update: As I thought my box here reboots in all cases. Running reboot or halt from then console menu or the webgui or using 'shutdown -r now'.

                              Steve

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.