Powerline adapters - speed issue
-
thanks Jason, i will check the powerline adapter and see what i can do
rob
-
Found out it was the cable between the router and the host powerline adapter,
the laptop was only seeing it as 100meg but pfsense was seeing it as 10meg but as soon as i changed the ethernet cable over with a new one laptop saw it as 1gig but pfsense sees it as 100meg
Interesting tho when its plugged in the powerline adapter it loses x10, has anyone noticed this?
Rob
-
If anyone wants to know its this -
tp link av500 mini powerline adapter
model no: tl-pa411
-
I have a similar model here, also a AV500 (tl-pa4010p), I use them every now and then (lazy patching, allows me to temporary extend any network connection).
I wouldn't put my money on it, but I think I would have noticed such sort of behaviour. When you say 'plugged into pfSense', what's on that end? (what is your HW?)Sure it isn't a wire-mapping issue? Laptops tend to be very forgiving (most do autoMDI-X), firewalls on the other hand…
-
I have a apu 1c board and then a cable between it and the powerline adapter and that was showing as 10megs on the main pfsense dashboard but as soon as i changed the cable its showing as 100megs
the powerline can do up to 500megs but the pfsense can only do 10/100/1000 so it must downgrade to 100 as it cant do 500?
-
500Mbit/s isn't an Ethernet standard. PowerLine devices that claim 500Mbit/s need to use a Gig-E port.
-
So it should read 500 then as my devices are all 1 gig?
-
So it should read 500 then as my devices are all 1 gig?
No, if working correctly it should read 1Gbit/s because that is the link speed between you and the adapter, you just won't be able to transfer any more than 500Mbit/s because that is the maximum link speed between your powerline adapters.
EDIT: I just looked up the model you posted. That adapter has a 10/100 port on it. Your link speed should be 100Mbit/s, not 1Gbit/s, and your maximum throughput will be limited accordingly. The 500Mbit/s on the box is pure marketing BS because you'll never come close. If you're getting a 100Mbit/s link with the cable changed out then it sounds like everything is working correctly.
-
It should advertise gig speed if it is a gig nic, even though the real throughput will be less.
But, to confirm you findings, I quickly plugged on into my APU1C, and it also settles on 100M(fd).No idea why… ::)
-
It should advertise gig speed if it is a gig nic, even though the real throughput will be less.
But, to confirm you findings, I quickly plugged on into my APU1C, and it also settles on 100M(fd).No idea why… ::)
Read my post above. The model in question only has a 10/100 port on it.
-
Hà. Good one… Missed your edit. You solved the mistery by reading the manual... ;D
-
now i understand there BS marketing jargon , when they say AV500, the internface is only 10/100, so you will never ever see 500mbps speeds
should have really got the AV500 gigabit, least i would have got 500mbps out of them as the interface is a gig
i cant believe i have been had!!!
-
now i understand there BS marketing jargon , when they say AV500, the internface is only 10/100, so you will never ever see 500mbps speeds
should have really got the AV500 gigabit, least i would have got 500mbps out of them as the interface is a gig
i cant believe i have been had!!!
Doubt it. Think of it like WiFi. Your link speed may be 300Mbit/s but the odds of you getting more than 40-50% of that, even with line of sight to the AP, are pretty long. The absolute best of the AV500 adapters are capable of about 250Mbit/s WHEN PLUGGED INTO THE SAME POWER STRIP. They all drop to 60-80Mbit/s in more realistic residential scenarios.
If you really need networking over power lines then I'd suggest waiting a month or two for the AV2 MIMO adapters to start hitting the streets (based on QCA7500). These should be branded as AV1000 or similar and should be capable of 2-3x the rate of older adapters and be able to maintain higher speeds in less optimal scenarios.