Separation between the wireless and wired network help

[MilesDeep]

What is your subnet?  Is it straight class C?  /24?  If so, you'll have to change the subnet scheme in order to separate wired from wireless.  If you can't change the subnet scheme, You'll have to use VLANs to separate the data.

[Derelict]

You're going to need another switch.  Either another unmanaged for your wireless APs or one that does VLANs so you can do both networks on one switch.

A new unmanaged will be cheaper and not require you to learn anything new or reconfigure anything.

[hadi57]

i am using separate  lan card for each network, separating the wifi from the wired network, also separating the wifi into groups connecting each group into their own separated lan card. i think this is the simplest way and its working fine with me.

hadi57

[firefox]

But you already have two NICs to separate wired and wireless traffic, card3 and card4.  :-
Are you saying that you need to position these extra APs such that they can only connect to the existing wired network?

no
i want them To connect to card 4
But I do not have this option
So I want to cancel card 4
and Split the network on card 3 into two

What is your subnet?  Is it straight class C?  /24?  If so, you'll have to change the subnet scheme in order to separate wired from wireless

it is 192.168.0.1/24 (see image)

how do i do that
That's what I'm trying to know
Is there an option in pfsense for two networks on one physical network
If I will choose there a smaller number
Will I have the option For another dhcp on the same network card
How to do it

You're going to need another switch.  Either another unmanaged for your wireless APs or one that does VLANs so you can do both networks on one switch.

A new unmanaged will be cheaper and not require you to learn anything new or reconfigure anything.

It would be easiest to buy a new switch
And put new cables in the wall
Up to location That the AP would be

I can not do that right now
It's a lot of work
And more money at the moment I do not have

So I want to do it on the existing network

[kejianshi]

You should be looking for a nice, cheap used vlan switch…  Or a miracle...

[firefox]

Bummer
I wanted to avoid drawing  cable for new points

In any case
Thanks everyone for trying to help

[kejianshi]

You won't need more cable if you get a VLAN switch - Thats sort of the point of the thing.

[stephenw10]

@firefox:

But you already have two NICs to separate wired and wireless traffic, card3 and card4.  :-
Are you saying that you need to position these extra APs such that they can only connect to the existing wired network?

no
i want them To connect to card 4
But I do not have this option
So I want to cancel card 4
and Split the network on card 3 into two

This confuses me. You say you're not restricted by the location of the new access points. So why can't you connect them to card4 along side the existing access point?

Your later responses seem to indicate that you need to to connect them to the existing wired network because you only have single cabling to that location.
In which case you can use VLANs but you will need a VLAN capable switch. They are not that expensive. If you don't need gigabit bandwidth you could split one cat5 run into 2 100Mbps connections. You could use an ethernet over powerline solution (or over co-ax if you have that). You might be able to setup the new APs as repeaters instead and do it wirelessly.

Steve

[firefox]

This confuses me. You say you're not restricted by the location of the new access points. So why can't you connect them to card4 along side the existing access point?

Just the opposite

I will try to explain
Maybe it does not go well then forgive me

Our house has seven rooms
Each room has two or three network points

All points are occupied
No Vacancy

In addition
There is a single point at home one side connected to pfsense
And on the other side of AP
This point is connected to the card 4

Everything comes to the switch being held in my room

Two of the rooms have a reception problem
Where I want to put ap
But I have no connection available

The only option to build a new line for every room

If you don't need gigabit bandwidth you could split one cat5

i do need gigabit bandwidth

I probably tomorrow or the day after tomorrow will pave two new lines

Hope I explained well

[Derelict]

The point is you can tag multiple VLANs across a single cable.  Put a switch at the end point, and break out the VLANs there.

I can just about guarantee nobody will notice you're running two VLANs over a gig-e link, speed wise.

[kejianshi]

What he said…  ^