Huawei k3765 3G HSPA USB Stick

edanny101

dmesg output :

ugen4.2: <huawei technology="">at usbus4
ugen4.2: <huawei technology="">at usbus4 (disconnected)
ugen4.2: <huawei technology="">at usbus4
u3g0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4
u3g0: Found 4 ports.
umass0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4
umass1: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4</huawei></huawei></huawei></huawei></huawei></huawei>

Houston commercial photography

I did try all ports, but i didn't reboot after each. I'm going to do so.

Houston commercial photography

About ppp log, where is it store?

There is a huge amount of cou uses for mdp5 after connect the modem to machine!!!
Top :

  PID USERNAME  THR PRI NICE   SIZE    RES STATE    TIME    WCPU COMMAND
16458 root        1 100    0 13920K  4844K RUN      0:51  94.48% mpd5

Guest

I see umass0 and umass1 in your boot log. You may need to do an eject on them or similar. Modeswitcher may be needed. I use internal Sierra MC7700 and it just works.

Generally data ports use the next to last interface. cuaU0.2 in your case.

PPP log is under system log. It has its own tab at top of page.

Guest

I use WAN as my 3G interface and set to DHCP for an IP. Get it working then you can rearrange interfaces. That may not work with usb devices though… I just wonder on your current setup with the dhcp settings on your WAN. You could try to swap maxis 3G interface to WAN until you get it working right. That way your not dealing with dual wan stuff.

Guest

With mpd5 using that much cpu usage -I assume somethings is amiss. Perhaps the modem script is not working correctly. A ppp log snip will help… Your u3g0 looks good so hardware is recognized. I am unsure about the umass stuff....

Guest

pfSense uses Freebsd underpinnings so much of this is valid

https://www.freebsd.org/doc/en/books/handbook/ppp-troubleshoot.html

You can manually connect and even probe the modem with AT commands from PPP console.

edanny101

ppp log:

May 10 10:31:55	ppp: [opt1_link0] CHAT: The modem is not responding to "AT" at ModemCmd: label.
May 10 10:31:55	ppp: [opt1_link0] MODEM: chat script failed
May 10 10:31:55	ppp: [opt1_link0] Link: DOWN event
May 10 10:31:55	ppp: [opt1_link0] LCP: Down event
May 10 10:31:55	ppp: [opt1_link0] Link: reconnection attempt 3 in 4 seconds
May 10 10:31:59	ppp: [opt1_link0] Link: reconnection attempt 3

No idea how to fix that!

Guest

OK so chat script failed.

If you try this setting it bypasses some of the modem script.

PPPconfig>>show advanced>>modem init string:
+CFUN=1

Guest

You sound like you have a parallel FreeBSD installation. |Check your FreeBSB bootlog there to see if it is showing umass0/1. I'm pretty sure that needs fixing up to work. I don't have much experience with usb fobs.

When your checking in Freebsd take note of the cuaU0.x port being used. PfSense will use the same.

edanny101

+CFUN=1 doesn't help.

CHAT: The modem is not responding to "AT+CFUN=1" at ModemCmd: label.

Boot log

ugen4.2: <huawei technology="">at usbus4
u3g0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4
u3g0: Found 4 ports.
umass0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4
umass1: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus4</huawei></huawei></huawei></huawei>

I think the modem is in storage mode instead of modem mode.

what i did without luck :

# pkg install usb-modeswitch
# rehash
# usb_modeswitch -v 0x12d1 -p 0x1520 -M "55534243123456780000000000000011060000000000000000000000000000" -W

# cat << EOF > /usr/local/etc/usb_modeswitch.conf
# Huawei K3765

DefaultVendor= 0x12d1
DefaultProduct= 0x1520

TargetVendor= 0x12d1
TargetProduct= 0x1465

MessageContent="55534243123456780000000000000011060000000000000000000000000000"
EOF

# cat << EOF > /etc/devd.conf
attach 10 {
device-name "ugen[0-9]+";
match "vendor" "0x12d1";
match "product" "0x1520";
action "/usr/local/sbin/3G.sh";
};
EOF

# cat < <eof>/usr/local/sbin/3G.sh
#!/bin/sh
sleep 3
/usr/local/sbin/usb_modeswitch -H -c /usr/local/etc/usb_modeswitch.conf
sleep 12
/usr/local/sbin/usb_modeswitch -H -c /usr/local/etc/usb_modeswitch.conf
EOF</eof>

The above didn't work,I think.
So, how can I switch mode in pfsense?

However,

pkg install mpd5

solved the high CPU consumption for mpd job.

Guest

I also noticed on that Freebsd setup blog referenced in your first post -that he was showing the device to have an UE0 interface. I don't see that in your boot log, does it appear? Might require some more modeswitcher work. I do see the umass on Freebsd so maybe thats no the problem. Modem might need a cdc mode kick

Guest

+CFUN=1 doesn't help.

Code: [Select]

CHAT: The modem is not responding to "AT+CFUN=1" at ModemCmd: label.

This is a problem. The only command we sent to modem was -Modem On-
If its not responding to that then there is a hardware issue.

Did you try going to console and use #8 Command Shell and type ppp just to see the output? It will give you some clues without diving into "Term" mode under ppp console… Probably need to address your hardware issue first though.