Pfsense 2.2.4 nanobsd config.xml not found
-
Thanks for reply, but I did this before flashing (dd if=/dev/zero of=/dev/sdb bs=1M count=1). Ubuntu comes with an window to tell me that it cannot mount or so the 53mb partition after flashing is done. are there this missing config files? If no one has problems with this image on this machines, it could be a problem with my hardware. can someone tell me, that it works with fresh installed 2.2.4 x86 nanobsd 4gb without old configs or so?
Thank you!
-
Eh? Why are you trying to mount UFS in Ubuntu?
-
I flashed the cf with dd in a console in ubuntu. At one point ubuntu tries to do something with the cf. Maybe not mounting, but it came up with a window that tells me, it can nothing do with the 53mb partition. Only the 53mb part! It could be that I missinterpret it, but same result under windows: pfsense don't start because config.xml is not there…
-
WTF?!?!? Are you trying to RUN the image under Windows ??!! Or what? You write the image, stick it to the Alix and boot from. There's serial console available, you can use PuTTY for that and post the console output….
Messing with/trying to mount/similar WTF under Windows or Ubuntu won't produce absolutely anything, let alone useful information. There's no UFS filesystem/BSD slices support in Windows, and very much doubt the Ubuntu kernel has this compiled in by default either.
-
no no no, stop thinking so bad! ;D
I first try to flash the pfsense image under windows to my 4gb cf card for the atix2d13, then as it don't work in the atix again under ubuntu. the serial console told me that pfsense can't come up because config.xml is not there.
I used this wiki https://doc.pfsense.org/index.php/Writing_Disk_Images
-
Sigh… Post the actual full output from the console, from where it boots to where it stops.
-
ok, need to do that on weekend. Thank you so long!
-
Hi again,
/boot/config: -h Consoles: serial port BIOS drive C: is disk0 BIOS 640kB/261120kB available memory FreeBSD/x86 bootstrap loader, Revision 1.1 (root@pfs22-i386-builder, Sat Jul 25 20:19:42 CDT 2015) Loading /boot/defaults/loader.conf /boot/kernel/kernel text=0x1218287 data=0x833668+0x279f60 syms=[0x4+0xf5400+0x4+0x16e574] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.1-RELEASE-p15 #0 c5ab052(releng/10.1)-dirty: Sat Jul 25 20:29:48 CDT 2015 root@pfs22-i386-builder:/usr/obj.i386/usr/pfSensesrc/src/sys/pfSense_wrap.10.i386 i386 FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512 VT: running with driver "vga". CPU: Geode(TM) Integrated Processor by AMD PCS (498.06-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x5a2 Family = 0x5 Model = 0xa Stepping = 2 Features=0x88a93d <fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx>AMD Features=0xc0400000 <mmx+,3dnow!+,3dnow!>real memory = 268435456 (256 MB) avail memory = 226222080 (215 MB) pnpbios: Bad PnP BIOS data checksum random device not loaded; using insecure entropy ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xc08122b0, 0) error 1 ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0812360, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0812410, 0) error 1 iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/. iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_bss_fw, 0xc083aa40, 0) error 1 iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/. iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_ibss_fw, 0xc083aaf0, 0) error 1 iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/. iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_monitor_fw, 0xc083aba0, 0) error 1 wlan: mac acl policy registered kbd0 at kbdmux0 K6-family MTRR support enabled (2 registers) random: <software, yarrow="">initialized ACPI BIOS Error (bug): A valid RSDP was not found (20130823/tbxfroot-223) ACPI: Table initialisation failed: AE_NOT_FOUND ACPI: Try disabling either ACPI or apic support. cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. pcib0 pcibus 0 on motherboard pci0: <pci bus="">on pcib0 Geode LX: PC Engines ALIX.2 v0.99h tinyBIOS V1.4a (C)1997-2007 pci0: <encrypt decrypt,="" entertainment="" crypto="">at device 1.2 (no driver attached) vr0: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1000-0x10ff mem 0xe0000000-0xe00000ff irq 10 at device 9.0 on pci0 vr0: Quirks: 0x2 vr0: Revision: 0x96 miibus0: <mii bus="">on vr0 ukphy0: <generic ieee="" 802.3u="" media="" interface="">PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow vr0: Ethernet address: ############### vr1: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1400-0x14ff mem 0xe0040000-0xe00400ff irq 11 at device 10.0 on pci0 vr1: Quirks: 0x2 vr1: Revision: 0x96 miibus1: <mii bus="">on vr1 ukphy1: <generic ieee="" 802.3u="" media="" interface="">PHY 1 on miibus1 ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow vr1: Ethernet address: ################# vr2: <via 10="" vt6105m="" rhine="" iii="" 100basetx="">port 0x1800-0x18ff mem 0xe0080000-0xe00800ff irq 15 at device 11.0 on pci0 vr2: Quirks: 0x2 vr2: Revision: 0x96 miibus2: <mii bus="">on vr2 ukphy2: <generic ieee="" 802.3u="" media="" interface="">PHY 1 on miibus2 ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow vr2: Ethernet address: ################## ath0: <atheros 9220="">mem 0xe00c0000-0xe00cffff irq 9 at device 12.0 on pci0 [ath] enabling AN_TOP2_FIXUP ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9220 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 isab0: <pci-isa bridge="">port 0x6000-0x6007,0x6100-0x61ff,0x6200-0x623f,0x9d00-0x9d7f,0x9c00-0x9c3f at device 15.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <amd cs5536="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 15.2 on pci0 ata0: <ata channel="">at channel 0 on atapci0 ata1: <ata channel="">at channel 1 on atapci0 ohci0: <ohci (generic)="" usb="" controller="">mem 0xefffe000-0xefffefff irq 12 at device 15.4 on pci0 usbus0 on ohci0 ehci0: <amd cs5536="" (geode)="" usb="" 2.0="" controller="">mem 0xefffd000-0xefffdfff irq 12 at device 15.5 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 cpu0 on motherboard pmtimer0 on isa0 orm0: <isa option="" rom="">at iomem 0xe0000-0xea7ff pnpid ORM0000 on isa0 atrtc0: <at realtime="" clock="">at port 0x70 irq 8 on isa0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <at timer="">at port 0x40 on isa0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 ppc0: parallel port not found. uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: console (115200,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 Timecounters tick every 1.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <amd>at usbus0 uhub0: <amd 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <amd>at usbus1 uhub1: <amd 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus1 ada0 at ata0 bus 0 scbus0 target 0 lun 0 ada0: <ts4gcf133 20110407="">CFA-7 device ada0: Serial Number ####################################### ada0: 66.700MB/s transfers (UDMA4, PIO 512bytes) ada0: 3823MB (7831152 512 byte sectors: 16H 63S/T 7769C) ada0: Previously was known as ad0 random: unblocking device. Timecounter "TSC" frequency 498061645 Hz quality 800 Root mount waiting for: usbus1 usbus0 uhub0: 4 ports with 4 removable, self powered Root mount waiting for: usbus1 uhub1: 4 ports with 4 removable, self powered Trying to mount root from ufs:/dev/ufs/pfsense0 [ro,sync,noatime]... Configuring crash dumps... /dev/ufs/pfsense0: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ufs/pfsense0: clean, 3272467 free (1131 frags, 408917 blocks, 0.0% fragmentation) /dev/ufs/cf: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ufs/cf: clean, 97477 free (29 frags, 12181 blocks, 0.0% fragmentation) Filesystems are clean, continuing... Mounting filesystems... Setting up memory disks... done. Disabling APM on /dev/ad0 ___ ___/ f \ / p \___/ Sense \___/ \ \___/ Welcome to pfSense 2.2.4-RELEASE ... Creating symlinks....warning: failed to load external entity "/conf/config.xml" ..ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout done. >>> Under 512 megabytes of ram detected. Not enabling APC. Warning: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. I4 Warning: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. I4 Oct 2 14:35:05 php-fpm[281]: /ecl.php: No config.xml found, attempting last known config restore. Oct 2 14:35:05 php-fpm[281]: /ecl.php: New alert found: No config.xml found, attempting last known config restore. Oct 2 14:35:05 php-fpm[281]: /ecl.php: No config.xml found, attempting last known config restore. Oct 2 14:35:05 php-fpm[281]: /ecl.php: New alert found: No config.xml found, attempting last known config restore. Oct 2 14:35:05 php-fpm[281]: /ecl.php: pfSense is restoring the configuration /cf/conf/backup/config-1441039848.xml Oct 2 14:35:05 php-fpm[281]: /ecl.php: New alert found: pfSense is restoring the configuration /cf/conf/backup/config-1441039848.xml Warning: fopen(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. 3 Warning: fopen(/conf/config.xml): failed to open stream: Not a directory in /etc/inc/xmlparse.inc on line 183 Oct 2 14:35:06 php-fpm[281]: /ecl.php: Error: could not open XML input Oct 2 14:35:07 php-fpm[281]: /ecl.php: pfSense is restoring the configuration /cf/conf/backup/config-1441039848.xml Oct 2 14:35:07 php-fpm[281]: /ecl.php: New alert found: pfSense is restoring the configuration /cf/conf/backup/config-1441039848.xml External config loader 1.0 is now starting... Launching the init system... done. Initializing.... Warning: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. I4 Warning: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. I4 .................. done. Starting device manager (devd)...done. Loading configuration....XML configuration file not found. pfSense cannot continue booting. Waiting (max 60 seconds) for system process `vnlru' to stop...done Waiting (max 60 seconds) for system process `bufdaemon' to stop...done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining...0 0 done All buffers synced. Uptime: 26s The operating system has halted. Please press any key to reboot.</ts4gcf133></amd></amd></amd></amd></at></at></isa></amd></ohci></ata></ata></amd></isa></pci-isa></atheros></generic></mii></via></generic></mii></via></generic></mii></via></encrypt></pci></software></software,></mmx+,3dnow!+,3dnow!></fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx>I try to write the cf under deft8. There dd comes to an end and after that, the system recognised the 3rd partition with 53MB, but don't try to automaticaly mount this partition like ubuntu. But anyway, same end.
Thanks
-
The thread you linked initially has no relation. That was never a problem in any release version.
Not being able to find the config most often happens when you write the upgrade image (which has no conf slice) rather than the one for new installs. That'd be a filename ending in "nanobsd-upgrade.img.gz" rather than "nanobsd.img.gz". Judging by the filename posted that wouldn't be the case, but make sure you're really using the right file. If you are, there's something wrong with how you're writing it, or your system's doing something to break it after it's written.
That's assuming it isn't throwing out any errors while writing. Try the 2 GB image instead, maybe your 4 GB CF is slightly too small to hold the 4 GB image.
-
Hi,
sorry for delay, but WAF was going down ;D
The 2g image works as it should. So I'm fine at this moment.
Thank you for your assistent
pfadmin