Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Apinger only working on wan 8/6/13 64bit snapshot

    2.1 Snapshot Feedback and Problems - RETIRED
    14
    54
    19.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • G
      grandrivers
      last edited by

      apinger is pending on opt inter faces works on wan
      monitor ips are blank even though there is an ip setup
      Aug 6 22:29:40 apinger: bind socket: Can't assign requested address
      Aug 6 22:29:40 apinger: SIGHUP received, reloading configuration.
      Aug 6 22:29:39 apinger: SIGHUP received, reloading configuration.
      Aug 6 22:29:36 apinger: Starting Alarm Pinger, apinger(19464)
      Aug 6 22:15:13 apinger: bind socket: Can't assign requested address
      Aug 6 22:15:13 apinger: SIGHUP received, reloading configuration.
      Aug 6 22:15:12 apinger: SIGHUP received, reloading configuration.
      Aug 6 22:15:09 apinger: Starting Alarm Pinger, apinger(21958)
      Aug 6 22:12:37 apinger: alarm canceled: DSL_DHCP(4.69.136.185) *** DSL_DHCPdown ***

      pfsense 2.4 super micro A1SRM-2558F
      C2558 8gig ECC  60gig SSD
      tripple Wan dual pppoe

      1 Reply Last reply Reply Quote 0
      • D
        doktornotor Banned
        last edited by 

        
kernel: pid 36656 (apinger), uid 0: exited on signal 11

        2.1-RC1 (i386)
        built on Tue Aug 6 16:41:59 EDT 2013
        FreeBSD 8.3-RELEASE-p9

        1 Reply Last reply Reply Quote 0
        • E
          eri--
          last edited by

          Can you share your configuration and /var/etc/apinger.conf?

          1 Reply Last reply Reply Quote 0
          • G
            grandrivers
            last edited by

            i had to roll back to 8/1/13 snap to fight with isp and  39% packet loss but anything that would help just let me know

            pfsense 2.4 super micro A1SRM-2558F
            C2558 8gig ECC  60gig SSD
            tripple Wan dual pppoe

            1 Reply Last reply Reply Quote 0
            • A
              athurdent
              last edited by

              I think what might be confusing, that apinger shows up in Services now. My test gateway has two gateway objects, each with monitoring disabled as I do not need this. apinger is down in Services. I'd say, that apinger probably does not have to run on that system.

              cat  /var/etc/apinger.conf

# pfSense apinger configuration file. Automatically Generated!

## User and group the pinger should run as
user "root"
group "wheel"

## Mailer to use (default: "/usr/lib/sendmail -t")
#mailer "/var/qmail/bin/qmail-inject"

## Location of the pid-file (default: "/var/run/apinger.pid")
pid_file "/var/run/apinger.pid"

## Format of timestamp (%s macro) (default: "%b %d %H:%M:%S")
#timestamp_format "%Y%m%d%H%M%S"

status {
        ## File where the status information should be written to
        file "/var/run/apinger.status"
        ## Interval between file updates
        ## when 0 or not set, file is written only when SIGUSR1 is received
        interval 5s
}

########################################
# RRDTool status gathering configuration
# Interval between RRD updates
rrd interval 60s;

## These parameters can be overridden in a specific alarm configuration
alarm default {
        command on "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
        command off "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
        combine 10s
}

## "Down" alarm definition.
## This alarm will be fired when target doesn't respond for 30 seconds.
alarm down "down" {
        time 10s
}

## "Delay" alarm definition.
## This alarm will be fired when responses are delayed more than 200ms
## it will be canceled, when the delay drops below 100ms
alarm delay "delay" {
        delay_low 200ms
        delay_high 500ms
}

## "Loss" alarm definition.
## This alarm will be fired when packet loss goes over 20%
## it will be canceled, when the loss drops below 10%
alarm loss "loss" {
        percent_low 10
        percent_high 20
}

target default {
        ## How often the probe should be sent
        interval 1s

        ## How many replies should be used to compute average delay
        ## for controlling "delay" alarms
        avg_delay_samples 10

        ## How many probes should be used to compute average loss
        avg_loss_samples 50

        ## The delay (in samples) after which loss is computed
        ## without this delays larger than interval would be treated as loss
        avg_loss_delay_samples 20

        ## Names of the alarms that may be generated for the target
        alarms "down","delay","loss"

        ## Location of the RRD
        #rrd file "/var/db/rrd/apinger-%t.rrd"
}
              1 Reply Last reply Reply Quote 0
              • G
                grandrivers
                last edited by

                on 8/1/13 snap

                pfSense apinger configuration file. Automatically Generated!

                User and group the pinger should run as

                user "root"
                group "wheel"

                Mailer to use (default: "/usr/lib/sendmail -t")

                #mailer "/var/qmail/bin/qmail-inject"

                Location of the pid-file (default: "/var/run/apinger.pid")

                pid_file "/var/run/apinger.pid"

                Format of timestamp (%s macro) (default: "%b %d %H:%M:%S")

                #timestamp_format "%Y%m%d%H%M%S"

                status {

                File where the status information should be written to

                file "/var/run/apinger.status"

                Interval between file updates

                when 0 or not set, file is written only when SIGUSR1 is received

                interval 5s
                }

                ########################################

                RRDTool status gathering configuration

                Interval between RRD updates

                rrd interval 60s;

                These parameters can be overridden in a specific alarm configuration

                alarm default {
                command on "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
                command off "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
                combine 10s
                }

                "Down" alarm definition.

                This alarm will be fired when target doesn't respond for 30 seconds.

                alarm down "down" {
                time 10s
                }

                "Delay" alarm definition.

                This alarm will be fired when responses are delayed more than 200ms

                it will be canceled, when the delay drops below 100ms

                alarm delay "delay" {
                delay_low 200ms
                delay_high 500ms
                }

                "Loss" alarm definition.

                This alarm will be fired when packet loss goes over 20%

                it will be canceled, when the loss drops below 10%

                alarm loss "loss" {
                percent_low 10
                percent_high 20
                }

                target default {

                How often the probe should be sent

                interval 1s

                How many replies should be used to compute average delay

                for controlling "delay" alarms

                avg_delay_samples 10

                How many probes should be used to compute average loss

                avg_loss_samples 50

                The delay (in samples) after which loss is computed

                without this delays larger than interval would be treated as loss

                avg_loss_delay_samples 20

                Names of the alarms that may be generated for the target

                alarms "down","delay","loss"

                Location of the RRD

                #rrd file "/var/db/rrd/apinger-%t.rrd"
                }
                alarm loss "CABLEMODEM_DHCPloss" {
                percent_low 3
                percent_high 15
                }
                alarm delay "CABLEMODEM_DHCPdelay" {
                delay_low 60ms
                delay_high 250ms
                }
                alarm down "CABLEMODEM_DHCPdown" {
                time 15s
                }
                target "4.53.194.9" {
                description "CABLEMODEM_DHCP"
                srcip "209.105.187.12"
                interval 3s
                alarms override "CABLEMODEM_DHCPloss","CABLEMODEM_DHCPdelay","CABLEMODEM_DHCPdown";
                rrd file "/var/db/rrd/CABLEMODEM_DHCP-quality.rrd"
                }

                alarm loss "DSL_DHCPloss" {
                percent_low 3
                percent_high 15
                }
                alarm delay "DSL_DHCPdelay" {
                delay_low 60ms
                delay_high 250ms
                }
                alarm down "DSL_DHCPdown" {
                time 15s
                }
                target "4.69.136.185" {
                description "DSL_DHCP"
                srcip "192.168.254.1"
                interval 3s
                alarms override "DSL_DHCPloss","DSL_DHCPdelay","DSL_DHCPdown";
                rrd file "/var/db/rrd/DSL_DHCP-quality.rrd"
                }

                alarm loss "OPT2GWv6loss" {
                percent_low 5
                percent_high 10
                }
                alarm delay "OPT2GWv6delay" {
                delay_low 60ms
                delay_high 250ms
                }
                alarm down "OPT2GWv6down" {
                time 100s
                }
                target "2620:0:ccd::2" {
                description "OPT2GWv6"
                srcip "2001:470:7b:15e::2"
                interval 20s
                alarms override "OPT2GWv6loss","OPT2GWv6delay","OPT2GWv6down";
                rrd file "/var/db/rrd/OPT2GWv6-quality.rrd"
                }

                pfsense 2.4 super micro A1SRM-2558F
                C2558 8gig ECC  60gig SSD
                tripple Wan dual pppoe

                1 Reply Last reply Reply Quote 0
                • P
                  phil.davis
                  last edited by

                  On the gateway status widget, the WANGW first gives a crazy high latency value (screenshot attached), then a few seconds later it goes to "pending". OPT1 always shows 0ms. Ping from a LAN client routing through either interface gives normal values.
                  2.1-RC1 (i386)
                  built on Tue Aug 6 16:41:59 EDT 2013
                  FreeBSD 8.3-RELEASE-p9
                  apinger.conf:

                  
# pfSense apinger configuration file. Automatically Generated!

## User and group the pinger should run as
user "root"
group "wheel"

## Mailer to use (default: "/usr/lib/sendmail -t")
#mailer "/var/qmail/bin/qmail-inject"

## Location of the pid-file (default: "/var/run/apinger.pid")
pid_file "/var/run/apinger.pid"

## Format of timestamp (%s macro) (default: "%b %d %H:%M:%S")
#timestamp_format "%Y%m%d%H%M%S"

status {
	## File where the status information should be written to
	file "/var/run/apinger.status"
	## Interval between file updates
	## when 0 or not set, file is written only when SIGUSR1 is received
	interval 5s
}

########################################
# RRDTool status gathering configuration
# Interval between RRD updates
rrd interval 60s;

## These parameters can be overridden in a specific alarm configuration
alarm default {
	command on "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
	command off "/usr/local/sbin/pfSctl -c 'service reload dyndns %T' -c 'service reload ipsecdns' -c 'service reload openvpn %T' -c 'filter reload' "
	combine 10s
}

## "Down" alarm definition.
## This alarm will be fired when target doesn't respond for 30 seconds.
alarm down "down" {
	time 10s
}

## "Delay" alarm definition.
## This alarm will be fired when responses are delayed more than 200ms
## it will be canceled, when the delay drops below 100ms
alarm delay "delay" {
	delay_low 200ms
	delay_high 500ms
}

## "Loss" alarm definition.
## This alarm will be fired when packet loss goes over 20%
## it will be canceled, when the loss drops below 10%
alarm loss "loss" {
	percent_low 10
	percent_high 20
}

target default {
	## How often the probe should be sent
	interval 1s

	## How many replies should be used to compute average delay
	## for controlling "delay" alarms
	avg_delay_samples 10

	## How many probes should be used to compute average loss
	avg_loss_samples 50

	## The delay (in samples) after which loss is computed
	## without this delays larger than interval would be treated as loss
	avg_loss_delay_samples 20

	## Names of the alarms that may be generated for the target
	alarms "down","delay","loss"

	## Location of the RRD
	#rrd file "/var/db/rrd/apinger-%t.rrd"
}
alarm loss "WANGWloss" {
	percent_low 40
	percent_high 50
}
alarm delay "WANGWdelay" {
	delay_low 4000ms
	delay_high 5000ms
}
alarm down "WANGWdown" {
	time 30s
}
target "8.8.4.4" {
	description "WANGW"
	srcip "10.49.82.1"
	interval 2s
	alarms override "WANGWloss","WANGWdelay","WANGWdown";
	rrd file "/var/db/rrd/WANGW-quality.rrd"
}

alarm loss "OPT1GWloss" {
	percent_low 40
	percent_high 50
}
alarm delay "OPT1GWdelay" {
	delay_low 4000ms
	delay_high 5000ms
}
alarm down "OPT1GWdown" {
	time 30s
}
target "8.8.8.8" {
	description "OPT1GW"
	srcip "10.49.81.1"
	interval 2s
	alarms override "OPT1GWloss","OPT1GWdelay","OPT1GWdown";
	rrd file "/var/db/rrd/OPT1GW-quality.rrd"
}

                  Gateways.png_thumb
                  Gateways.png

                  As the Greek philosopher Isosceles used to say, "There are 3 sides to every triangle."
                  If I helped you, then help someone else - buy someone a gift from the INF catalog http://secure.inf.org/gifts/usd/

                  1 Reply Last reply Reply Quote 0
                  • N
                    NOYB
                    last edited by

                    Working fine here.
                    Try stop and restart apinger.

                    Gateways.jpg
                    Gateways.jpg_thumb

                    1 Reply Last reply Reply Quote 0
                    • P
                      phil.davis
                      last edited by

                      I stopped/restarted apinger on both systems that I had upgraded. The gateway status widget latencies are now showing fine. I had upgraded 3 systems to Aug 6 snapshot - the 2 with multi-gateways had these symptoms. The 1 with only 1 gateway did not have a problem. Not a big enough sample size to decide if multiple gateways being monitored is the real trigger for the "feature". Will report tomorrow if I see the latency numbers go silly again.

                      As the Greek philosopher Isosceles used to say, "There are 3 sides to every triangle."
                      If I helped you, then help someone else - buy someone a gift from the INF catalog http://secure.inf.org/gifts/usd/

                      1 Reply Last reply Reply Quote 0
                      • D
                        doktornotor Banned
                        last edited by

                        @phil.davis:

                        I had upgraded 3 systems to Aug 6 snapshot - the 2 with multi-gateways had these symptoms. The 1 with only 1 gateway did not have a problem. Not a big enough sample size to decide if multiple gateways being monitored is the real trigger for the "feature". Will report tomorrow if I see the latency numbers go silly again.

                        Well, if IPv6 tunnel counts as multigateway, then count me in.

                        1 Reply Last reply Reply Quote 0
                        • jimpJ
                          jimp Rebel Alliance Developer Netgate
                          last edited by

                          It seems to be that the longer the delay to the gateway, the more likely there is to be a problem compounded over time.

                          I set one of my gateways in a VM last night to 8.8.8.8 and within an hour it was into the thousands of ms in delays when in reality it was ~50ms.

                          There is also still an issue with changing monitor IPs requiring a manual restart of apinger.

                          Remember: Upvote with the 👍 button for any user/post you find to be helpful, informative, or deserving of recognition!

                          Need help fast? Netgate Global Support!

                          Do not Chat/PM for help!

                          1 Reply Last reply Reply Quote 0
                          • D
                            doktornotor Banned
                            last edited by

                            @jimp:

                            It seems to be that the longer the delay to the gateway, the more likely there is to be a problem compounded over time.
                            I set one of my gateways in a VM last night to 8.8.8.8 and within an hour it was into the thousands of ms in delays when in reality it was ~50ms.

                            Pretty much same here. If I really use the real GW, it does not happen. However monitoring the real GW is rather useless for me, I need to monitor real internet connectivity, not a device a couple of meters away from the firewall.

                            1 Reply Last reply Reply Quote 0
                            • T
                              traxanos
                              last edited by

                              we have the same problem. ping default gateway normal (1.3ms). when we ping the next hop gateway, we have a ping over 600ms). a pink from terminal show a ping of 1.4ms. after a restart of apinger the values correct again.

                              1 Reply Last reply Reply Quote 0
                              • T
                                traxanos
                                last edited by

                                hi we have now used the gateway ip for monitoring and we have the problem on the backup firewall, too. the ms stacked up from time to time. it start with 1ms and after some hours the apinger is over 2000ms. after restart apinger, it start with 1ms and from time to time the value was higher.

                                1 Reply Last reply Reply Quote 0
                                • G
                                  ggzengel
                                  last edited by

                                  My (calculated) ping times growing, too.
                                  My rrd graphs from last 6 month are less than 1 pixel.

                                  1 Reply Last reply Reply Quote 0
                                  • D
                                    DrCain
                                    last edited by

                                    Same problem here.

                                    Is it possible to cut out the effected part of the rrd graph?

                                    1 Reply Last reply Reply Quote 0
                                    • M
                                      mastahfr
                                      last edited by

                                      I've a hard feeling my problem is related: https://redmine.pfsense.org/issues/3138
                                      Multi wan is going fubbar since I switched from RC0 to RC1 a couple of days ago.

                                      I also confirm that I got the increasing of ping in a linear curve path.

                                      1 Reply Last reply Reply Quote 0
                                      • N
                                        NOYB
                                        last edited by

                                        @DrCain:

                                        Is it possible to cut out the effected part of the rrd graph?

                                        You could export the RRD to XLM, edit the XML to re-set the values of the effected part of the graph.  Then import the XLM back to RRD.

                                        Export / Import RRD Database
                                        /usr/local/bin/rrdtool dump rrddatabase xmldumpfile
                                        /usr/local/bin/rrdtool restore -f xmldumpfile rrddatabase

                                        1 Reply Last reply Reply Quote 0
                                        • P
                                          phil.davis
                                          last edited by

                                          I had upgraded a multi-WAN site from 6 Aug 16:41:59 EDT 2013 to the latest snapshot yesterday (so I guess it would have been about a 12 Aug snapshot).
                                          The 6 Aug snapshot was the one when apinger was added to the Services Status list, and apinger started counting up big numbers in the latency field. I was hoping that the later snap would fix everything.
                                          The site was remote from me, and reported "no/intermittent internet". It did seem that OpenVPN links to it were coming and going. I couldn't get on to it long enough to see anything real. From the descriptions, it was probably constantly failing over from 1 gateway to the other and back, and/or thinking that both gateways were down…
                                          I got them to switch slices and reboot, so it is back on 6 Aug snapshot. When I logged in just now the latency figures on the OPT! gateway were showing silly high numbers. I have disabled gateway monitoring on both gateways, and things have stabilised. For the moment, there will be no auto-failover at this site.
                                          Unfortunately I can't give any better information, and for obvious reasons I don't want to roll forward at this site just now!
                                          How are the apinger changes going? Do others have multi-WAN test systems that can be used as guinea-pigs?

                                          As the Greek philosopher Isosceles used to say, "There are 3 sides to every triangle."
                                          If I helped you, then help someone else - buy someone a gift from the INF catalog http://secure.inf.org/gifts/usd/

                                          1 Reply Last reply Reply Quote 0
                                          • jimpJ
                                            jimp Rebel Alliance Developer Netgate
                                            last edited by

                                            I have four gateways on three interfaces on a test VM and it was OK there, but they aren't "real" WANs.

                                            Can you give any more information about your exact gateway config there?

                                            Remember: Upvote with the 👍 button for any user/post you find to be helpful, informative, or deserving of recognition!

                                            Need help fast? Netgate Global Support!

                                            Do not Chat/PM for help!

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.