1 WAN 2 LAN

nevr0sed

I'll get back to you after lunch.

Bon appétit ! :)

KOM

OK, so your client that is timing everything out. You already gave me the output of ifconfig. Any difference if you manually configure the client with static IP, netmask, DNS and gateway?

nevr0sed

Ok,

Just to be sure in the manual config:

IP : 192.168.2.2
netmask : 255.255.255.0
DNS : 192.168.2.1 (?)
Gateway: 192.168.2.1 (?)

I'm not sure about the DNS and the GW.

Thank you.

n.

nevr0sed

@nevr0sed:

Ok,

Just to be sure in the manual config:

IP : 192.168.2.2
netmask : 255.255.255.0
DNS : 192.168.2.1 (?)
Gateway: 192.168.2.1 (?)

I'm not sure about the DNS and the GW.

Thank you.

n.

Ok with the config above, I still can ping the PFsense, the other lan (PRIVATELAN).
Still no win with the pings on the www.
Before this config, when I pinged www.google.com I got an IP address as return but ICMP fail. Now it tell me

cannot resolve www.google.com : Unknown host.

So I guess that there is something to do with the DNS ?

n.

KOM

Gateway is correct, DNS can be the same as the gateway (pfsense) as long as you're running the DNS forwarder or resolver. Just to be safe you could try setting DNS to 192.168.2.1 8.8.8.8 so that it falls back to Google DNS if pfSense DNS isn't running for whatever reason.

tigs

try deleting rule #1, 3, 4, and 5, keep only rule #2.

AND

you can also define your gateway in the advanced section of the setting, instead of using "destinations"

change PUBLICLAN address to PUBLICLAN net instead.

You can also consider using two different rules for IPV4 and IPV6.

this is what worked for me.

nevr0sed

@KOM:

Gateway is correct, DNS can be the same as the gateway (pfsense) as long as you're running the DNS forwarder or resolver. Just to be safe you could try setting DNS to 192.168.2.1 8.8.8.8 so that it falls back to Google DNS if pfSense DNS isn't running for whatever reason.

Thanks, ok just to be sure where shall I add this DNS ?
In the DHCP configuration or elsewhere ?

Find attached a couple of screens.

gkrellShoot_03-03-16_212334.jpg_thumb

gkrellShoot_03-03-16_212406.jpg_thumb

nevr0sed

@tigs:

try deleting rule #1, 3, 4, and 5, keep only rule #2.

AND

change PUBLICLAN address to PUBLICLAN net instead.

You can also consider using two different rules for IPV4 and IPV6.

Hi Tigs,
Thanks for your help.

This is the current rules I have. As I have modified some.

Let me know which ones to delete again, and on which interface.

Thank you very much !

n.

gkrellShoot_03-03-16_213103.jpg_thumb

gkrellShoot_03-03-16_213113.jpg_thumb

KOM

Thanks, ok just to be sure where shall I add this DNS ?

In your client's TCP/IP config. I'm a little busy in my real job at the moment applying a bunch of ESXi patches so I can't give this much attention for the next little while.

tigs

@nevr0sed:

@tigs:

try deleting rule #1, 3, 4, and 5, keep only rule #2.

AND

change PUBLICLAN address to PUBLICLAN net instead.

You can also consider using two different rules for IPV4 and IPV6.

Hi Tigs,
Thanks for your help.

This is the current rules I have. As I have modified some.

Let me know which ones to delete again, and on which interface.

Thank you very much !

n.

You need to define "source" which is the "PUBLICLANINTERFACE net".

nevr0sed

Ok,

I have done what you said. I have tried putting other rules such as :
But nothing works.

PUBLICLANINTERFACE
Source: * – Dest: *
Source: EXTERNALWAN – Dest: *
Source: * – Dest: EXTERNALWAN
EXTERNALWAN
Source: PUBLICLANINTERFACE – Dest: *
Source: * – Dest: PUBLICLANINTERFACE

Maybe, but I am no expert, can't it be something related to the DNS or Gateway ?

Thanks again for all the support guys.

n.

tigs

@nevr0sed:

Ok,

I have done what you said. I have tried putting other rules such as :
But nothing works.

PUBLICLANINTERFACE

Source: * – Dest: *

Source: EXTERNALWAN – Dest: *

Source: * – Dest: EXTERNALWAN

EXTERNALWAN

Source: PUBLICLANINTERFACE – Dest: *

Source: * – Dest: PUBLICLANINTERFACE

Maybe, but I am no expert, can't it be something related to the DNS or Gateway ?

Thanks again for all the support guys.

n.

nevr0sed

@tigs:

What you did is not what I said for sure. You need to read carefully.

You are over-complicating things, which may not always be a good thing.

You need:

1, Get rid of all your WAN rules, at least for the sake of trouble shooting. Someone already mentioned that to you.
2, you only need one rule for the PUBLICLANINTERFACE, Which I also said as well. I have attached a picture of what a working rule should look like.

Yes sure, it's what I did. I have tried in the very first place what you guys told me, and redid it, with no success.

I have tried with and without the Gateway. Still the same, no internet connection. But all networks are pingable.

Thanks again.

n.

KOM

This really shouldn't be this hard. Let's start from the beginning.

Your OPT1 interface, aka new NIC, is configured as 192.168.2.1. You havea firewall rule on OPT1 tab that allows all for IPv4. You have DHCP enabled with a range of 1-254, which isn't correct as the gateway address (192.168.2.1) should not be part of the DHCP address pool. Your client gets its net config via DHCP (192.168.2.2), but attempts to access websites result in a timeout.

How is your client connected to OPT1, via a switch? What OS is your client running?

nevr0sed

Hello KOM,

@KOM:

This really shouldn't be this hard. Let's start from the beginning.

I know ! It's just amazing how wicked it is that it ain't working… :o

Your OPT1 interface, aka new NIC, is configured as 192.168.2.1.

Yes.

You havea firewall rule on OPT1 tab that allows all for IPv4.

Yes.

You have DHCP enabled with a range of 1-254, which isn't correct as the gateway address (192.168.2.1) should not be part of the DHCP address pool. Your client gets its net config via DHCP (192.168.2.2), but attempts to access websites result in a timeout.

Yes. So I have changed to range to 192.168.2.16 - 192.168.2.32

How is your client connected to OPT1, via a switch? What OS is your client running?

My client IP now is 192.168.2.17
My client Subnet Mask is : 255.255.255.0
Routeur is : 192.168.2.1
DNS Server : 192.168.2.1
Search Domain : myhomedomain.org

My client is connected through a Home Switch http://www.staples.com/NETGEAR-ProSAFE-5-Port-Gigabit-Ethernet-Desktop-Switch-GS105NA/product_565423

The client is a Mac Mini.

I am pretty sure that there is something to do with the DNS… Although I have no clue what do to with it.

Thanks for your help again.

n.

KOM

I am pretty sure that there is something to do with the DNS

What's your output if you drop to a shell and type nslookup www.google.com?

nevr0sed

Hi,

Server:         192.168.2.1
Address:        192.168.2.1#53

** server can't find wwww.google.com: NXDOMAIN

I have no idea what that means…

n.

KOM

It means that you can't resolve hostnames to IP addresses, as if your DNS isn't working. Your DNS server is pfSense itself. Previous screens show you're running the DNS Resolver. Under your DNS Resolver settings, uncheck the Enable forwarding mode box and try it again. Do you have anything configured under General Settings - DNS Servers?

nevr0sed

@KOM:

It means that you can't resolve hostnames to IP addresses, as if your DNS isn't working. Your DNS server is pfSense itself. Previous screens show you're running the DNS Resolver. Under your DNS Resolver settings, uncheck the Enable forwarding mode box and try it again. Do you have anything configured under General Settings - DNS Servers?

Hi,

I have done what you requested. Still no changes in the problem.
I have 2 DNS servers that will be used on the PRIVATELANINTERFACE to configure a VPN on it. I have tried with them and without, and nothing changes.

Thanks again. This issue is starting to make me crazy… :)

n.

![Image 1.png](/public/imported_attachments/1/Image 1.png)
![Image 1.png_thumb](/public/imported_attachments/1/Image 1.png_thumb)
![Image 2.png](/public/imported_attachments/1/Image 2.png)
![Image 2.png_thumb](/public/imported_attachments/1/Image 2.png_thumb)

KOM

I don't know then. Maybe someone else has some suggestions.