Upgrade from 2.2.6 to 2.3 Release fails - can't find kernel, can't mount filesys
-
Great! Once you have a correct /etc/fstab that works after rebooting, you can run /usr/local/sbin/ufslabels.sh to permanently adjust fstab to use UFS labels rather than the device name
How can I edit fstab?
Now I have in /etc/fstab
/dev/vtbd0s1a for /
/dev/vtbd0s1b for swap
and in /dev/
ad0s1a
ad0s1
and no da0s1aAnd how to run /usr/local/sbin/ufslabels.sh?
-
Actually, your second point in the above post (https://forum.pfsense.org/index.php?topic=109802.msg612250#msg612250) solves the issue. pfSense v2.3 was trying to load the root from /dev/ada0s1a, when it should have been using /dev/da0s1a. Entering "ufs:/dev/da0s1a" at the mountroot> prompt boots v2.3 correctly. After the booting, /etc/fstab shows it's trying to mount the device directly, not by ufs id. Editing the fstab and rebooting solves the issue and allows the machine to reboot in the future without issue.
Also, the two posts linked in the Hyper-V thread both say the issue is with Hyper-V 2008 R2 and is fixed in Hyper-V 2012. I'm running Hyper-V 2012 R2, so don't believe they're related.
Just to confirm I had exactly the same problem on my HyperV 2012R2 pfSense VM. It's also a pretty old install so was using device names rather than the UFS label.
After a brief panic I got round it in exactly the same way, will take a look at ufslabels.sh later. -
-
vi and ee both exist in the shell, and both can be used.
If they won't run, try using the full path: /usr/bin/vi or /usr/bin/ee
-
Mounting from ufs:/dev/ada0xxx failed with error 19
mountroot>IS this a 1 GB CF Card? Then you should go with a 2 GB or 4 GB since the version 2.3 is no more for 1 GB
CF Cards!a ? did only show the cd rom…
And on the other side with 1 GB RAM you could be easily run out of RAM space or in other words
1 GB RAM is perhaps to small! Insert as a minimum 2 GB or better 4 GB if needed and pending on the
the installed packets or used services.Now I am trying to reinstall 2.2.6 again - seems to work fine, now…
Could be a short work around until the version 2.3.1 is out, but then perhaps read once more the lines above
with 1 GB CF Card and 1 GB RAM it would be perhaps underpowered or not right sorted.No Idea what 2.3 does there…?
Is this a 32Bit or 64Bit install?
After dozens of flawless updates, now this..:-(
There will be each version one day where the user or customer should be thinking on to do something
by its own intense because his hardware could be outdated at one day. So if you are using a 1 GB CF card
change it against a 2 GB or 4 GB model, the 1 GB CF Cards are to small, and if then all other things must be
running in the RAM als the 1 GB of RAM is to small too. -
vi and ee both exist in the shell, and both can be used.
If they won't run, try using the full path: /usr/bin/vi or /usr/bin/ee
How do I use the editor to edit the file /etc/fstab?
I can't open vi or ee, see attachment!
-
Sounds almost like you don't have vi installed on your box.
It should come in from a standard install.What happens if you type:
ls -al /usr/bin/vi
At a command prompt?
Are you running a bare metal or VM install?
How did you load pfSense? -
Sounds almost like you don't have vi installed on your box.
It should come in from a standard install.What happens if you type:
ls -al /usr/bin/vi
At a command prompt?
Are you running a bare metal or VM install?
How did you load pfSense?illegal option – a
My pfSense broken after upgrading to 2.3 via gui.
System can't find kernel (see attachment).
PfSense installed on Proxmox (kvm).
-
That's the boot loader prompt, not the single user mode shell.
-
Sorry, I looked back through the thread and realized your not getting a properly mounted system drive, but you're getting farther than the OP in this thread.
Normally you need to mount the required disk and prove that the pfSense install is up and running before making any of those fstab changes.
As far as the "ls" command, try it without the "-al" -> "ls /usr/bin/vi".
You may be able to recover your install, but it's probably far easier just to reinstall and reload a config backup.
-
-
@kpa:
That's the boot loader prompt, not the single user mode shell.
How enter to user mode shell?
https://doc.pfsense.org/index.php/Locked_out_of_the_WebGUI
That is for a different problem but it documents how to get to the single user mode shell.
-
This worked for me: http://blog.stefcho.eu/upgrade-from-pfsense-2-1-5-to-2-2-on-hyper-v/
