D-Link DWM-157 USB Stock not recognized

chedxb

Thanks Steve, I will try with a different modem.

Best,

Savas

stephenw10

If it is the C1 version it just needs to be ejected anyway:
https://github.com/NetworkManager/usb_modeswitch-data/blob/master/usb_modeswitch.d/2001:a407

And then it may appear as a usb Ethernet device which you can use directly. There are issues with that though.

Steve

chedxb

I am afraid it is D1

chedxb

I also tried usb_modeswitch -v 2001 -p a407 -K -W, however it didn't generate any verbose output.

and this is what I see on the system log,

Apr 15 18:17:57 kernel da0: quirks=0x2<NO_6_BYTE>
Apr 15 18:17:57 kernel da0: Attempt to query device size failed: ILLEGAL REQUEST, Invalid field in CDB
Apr 15 18:17:57 kernel da0: 40.000MB/s transfers
Apr 15 18:17:57 kernel da0: <HSPA USB SCSI CD-ROM 6225> Removable Direct Access SCSI device
Apr 15 18:17:57 kernel da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Apr 15 18:17:57 kernel umass0: <Mass Storage > on usbus4
Apr 15 18:17:57 kernel umass0 on uhub1
Apr 15 18:17:57 kernel ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4
Apr 15 18:17:55 kernel ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4 (disconnected)
Apr 15 18:17:55 kernel umass0: detached
Apr 15 18:17:55 kernel (cd0:umass-sim0:0:0:0): Periph destroyed
Apr 15 18:17:55 kernel cd0: <HSPA USB SCSI CD-ROM 6225> s/n 531399703502680 detached
Apr 15 18:17:55 kernel cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Apr 15 18:17:55 kernel umass0: at uhub1, port 1, addr 2 (disconnected)
Apr 15 18:17:36 kernel cd0: quirks=0x10<10_BYTE_ONLY>
Apr 15 18:17:36 kernel cd0: 14MB (28672 512 byte sectors)
Apr 15 18:17:36 kernel cd0: 40.000MB/s transfers
Apr 15 18:17:36 kernel cd0: Serial Number 531399703502680
Apr 15 18:17:36 kernel cd0: <HSPA USB SCSI CD-ROM 6225> Removable CD-ROM SCSI device
Apr 15 18:17:36 kernel cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Apr 15 18:17:36 kernel umass0: <Mass Storage > on usbus4
Apr 15 18:17:36 kernel umass0 on uhub1
Apr 15 18:17:36 kernel ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4

basically when I run usb_modeswitch -v 2001 -p a407 -K -W, it ejects cd0 and turns into da0, not modem.

Best,

Savas

stephenw10

Mmm, it sure looks like a C1 version in many ways. You see anything else in the system log after you do that?

Try running usbconfig dump_all_desc against it after you have ejected it to change it's mode like LOM suggested.

Steve

chedxb

I cannot post the logs, I am getting SPAM message

"Post content was flagged as spam by Akismet.com"

chedxb

so these are the interfaces after the camcontrol eject cd0 command.

MI_00 D-Link Mobile Broadband Device (Network Adapter) (cdc_mbim)
MI_02 D-Link HSPA+DataCard Diagnostics Interface (also ppp dialup modem)
MI_03 D-Link HSPA+DataCard NMEA Device
MI_04 D-Link HSPA+DataCard Speech Port
MI_05 D-Link HSPA+DataCard Debug Port
MI_06 USB Mass Storage Device

So I understand as follows,

Since the drivers are not available in pfSense/BSD for the interfaces from 0 to 5, when I do camcontrol eject cd0, it uses the 6th interface (USB Mass Storage Device)

Thoughts?

Best,

Savas

stephenw10

Yes, only interfaces 2 and 3 would otherwise be available if u3g attached to them.

The usbconfig output should show those interfaces though even if no driver does attach.

I have upvoted some of your posts which should stop akismet triggering but it does seem have a mind of it's own. We have almost no control over it.

Steve

chedxb

ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA)

bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0200
bDeviceClass = 0x00ef <Miscellaneous device>
bDeviceSubClass = 0x0002
bDeviceProtocol = 0x0001
bMaxPacketSize0 = 0x0040
idVendor = 0x2001
idProduct = 0x7d0e
bcdDevice = 0x0300
iManufacturer = 0x0009 <D-Link,Inc >
iProduct = 0x000a <D-Link DWM-157>
iSerialNumber = 0x0000 <no string>
bNumConfigurations = 0x0001

Configuration index 0

bLength = 0x0009
bDescriptorType = 0x0002
wTotalLength = 0x00e4
bNumInterfaces = 0x0007
bConfigurationValue = 0x0001
iConfiguration = 0x0000 <no string>
bmAttributes = 0x00a0
bMaxPower = 0x00fa

Additional Descriptor

bLength = 0x08
bDescriptorType = 0x0b
bDescriptorSubType = 0x00
RAW dump:
0x00 | 0x08, 0x0b, 0x00, 0x02, 0x02, 0x0e, 0x00, 0x01


Interface 0
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0000
bAlternateSetting = 0x0000
bNumEndpoints = 0x0001
bInterfaceClass = 0x0002 <Communication device>
bInterfaceSubClass = 0x000e
bInterfaceProtocol = 0x0000
iInterface = 0x0001 <COM(comm_if)>

Additional Descriptor

bLength = 0x05
bDescriptorType = 0x24
bDescriptorSubType = 0x00
RAW dump:
0x00 | 0x05, 0x24, 0x00, 0x10, 0x01


Additional Descriptor

bLength = 0x05
bDescriptorType = 0x24
bDescriptorSubType = 0x06
RAW dump:
0x00 | 0x05, 0x24, 0x06, 0x00, 0x01


Additional Descriptor

bLength = 0x0c
bDescriptorType = 0x24
bDescriptorSubType = 0x1b
RAW dump:
0x00 | 0x0c, 0x24, 0x1b, 0x00, 0x01, 0x00, 0x02, 0x10,
0x08 | 0x40, 0xdc, 0x05, 0x20


Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0088 <IN>
bmAttributes = 0x0003 <INTERRUPT>
wMaxPacketSize = 0x0040
bInterval = 0x0001
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 1
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0001
bAlternateSetting = 0x0000
bNumEndpoints = 0x0000
bInterfaceClass = 0x000a <CDC-data>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0002
iInterface = 0x0002 <COM(data_if)>


Interface 1 Alt 1
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0001
bAlternateSetting = 0x0001
bNumEndpoints = 0x0002
bInterfaceClass = 0x000a <CDC-data>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0002
iInterface = 0x0000 <no string>

Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0081 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0001 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 2
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0002
bAlternateSetting = 0x0000
bNumEndpoints = 0x0003
bInterfaceClass = 0x00ff <Vendor specific>
bInterfaceSubClass = 0x0002
bInterfaceProtocol = 0x0001
iInterface = 0x0003 <COM(comm_if)>

Additional Descriptor

bLength = 0x05
bDescriptorType = 0x24
bDescriptorSubType = 0x00
RAW dump:
0x00 | 0x05, 0x24, 0x00, 0x10, 0x01


Additional Descriptor

bLength = 0x04
bDescriptorType = 0x24
bDescriptorSubType = 0x02
RAW dump:
0x00 | 0x04, 0x24, 0x02, 0x0f


Additional Descriptor

bLength = 0x05
bDescriptorType = 0x24
bDescriptorSubType = 0x06
RAW dump:
0x00 | 0x05, 0x24, 0x06, 0x02, 0x03


Additional Descriptor

bLength = 0x05
bDescriptorType = 0x24
bDescriptorSubType = 0x01
RAW dump:
0x00 | 0x05, 0x24, 0x01, 0x03, 0x03


Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0087 <IN>
bmAttributes = 0x0003 <INTERRUPT>
wMaxPacketSize = 0x0040
bInterval = 0x0003
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0082 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 2
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0002 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 3
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0003
bAlternateSetting = 0x0000
bNumEndpoints = 0x0002
bInterfaceClass = 0x00ff <Vendor specific>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0000
iInterface = 0x0005 <COM(data_if)>

Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0083 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0003 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 4
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0004
bAlternateSetting = 0x0000
bNumEndpoints = 0x0002
bInterfaceClass = 0x00ff <Vendor specific>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0000
iInterface = 0x0006 <COM(data_if)>

Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0084 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0004 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 5
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0005
bAlternateSetting = 0x0000
bNumEndpoints = 0x0002
bInterfaceClass = 0x00ff <Vendor specific>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0000
iInterface = 0x0007 <COM(data_if)>

Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0085 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0005 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000


Interface 6
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0006
bAlternateSetting = 0x0000
bNumEndpoints = 0x0002
bInterfaceClass = 0x0008 <Mass storage>
bInterfaceSubClass = 0x0006
bInterfaceProtocol = 0x0050
iInterface = 0x0008 <Mass Storage >

Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0086 <IN>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

Endpoint 1
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0006 <OUT>
bmAttributes = 0x0002 <BULK>
wMaxPacketSize = 0x0200
bInterval = 0x0000
bRefresh = 0x0000
bSynchAddress = 0x0000

chedxb

@stephenw10 said in D-Link DWM-157 USB Stock not recognized:

Yes, only interfaces 2 and 3 would otherwise be available if u3g attached to them.

The usbconfig output should show those interfaces though even if no driver does attach.

I have upvoted some of your posts which should stop akismet triggering but it does seem have a mind of it's own. We have almost no control over it.

Steve

it worked now, I just posted the log

stephenw10

Yep, it really looks like that is a C1 device mislabelled. But that is still not recognised by u3g even is the most recent FreeBSD. https://github.com/freebsd/freebsd/blob/master/sys/dev/usb/usbdevs

It's probably relatively easy to add it. The serial interfaces are there they just need to be attached but that's not something I can do. To add new devices requires rebuilding the kernel and hence it's only really practical to do in FreeBSD rather then in pfSense. Those changes usually happen there first and are brought into pfSense though it does happen the other way on occasion.

It's still easier to use a different modem.

Steve

chedxb

Thanks Steve, how can I ask FreeBSD community to add this device? For some reason, this is/used to be a popular device in the region I live (middle east) and it would be nice to add it for the future users. Meanwhile I will try with a Huawei E173.

stephenw10

There are examples of people having done it for other devices. I would start by looking on the FreeBSD forums for other threads. And then opening your own thread if it's not obvious.
Ultimately you would be looking to make a patch against udbdevs and u3g and then issue a pull request for it.

It would be much easier to test if u3g was a loadable kernel module but I don't think that s possible.

Steve

chedxb

I found this, https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=196362

I will post shortly with the experience we had here.

chedxb

@chedxb said in D-Link DWM-157 USB Stock not recognized:

I found this, https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=196362

I will post shortly with the experience we had here.

As explained here, I tried
usb_modeswitch -v 2001 -p a407 -m 1 -M 555342431234567800000000000003f0010300000000000000000000000000 -R 1

and I got this,

Apr 16 16:51:21 kernel da0: quirks=0x2<NO_6_BYTE>
Apr 16 16:51:21 kernel da0: Attempt to query device size failed: ILLEGAL REQUEST, Invalid field in CDB
Apr 16 16:51:21 kernel da0: 40.000MB/s transfers
Apr 16 16:51:21 kernel da0: <HSPA USB SCSI CD-ROM 6225> Removable Direct Access SCSI device
Apr 16 16:51:21 kernel da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Apr 16 16:51:21 kernel umass0: <Mass Storage > on usbus4
Apr 16 16:51:21 kernel umass0 on uhub1
Apr 16 16:51:21 kernel ue0: Ethernet address: 02:00:ff:aa:aa:aa
Apr 16 16:51:21 kernel ue0: <USB Ethernet> on cdce0
Apr 16 16:51:21 kernel cdce0: <COMcommif> on usbus4
Apr 16 16:51:21 kernel cdce0 on uhub1
Apr 16 16:51:21 kernel ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4
Apr 16 16:51:19 kernel ugen4.2: <D-Link,Inc D-Link DWM-157> at usbus4 (disconnected)
Apr 16 16:51:19 kernel umass0: detached
Apr 16 16:51:19 kernel (cd0:umass-sim0:0:0:0): Periph destroyed
Apr 16 16:51:19 kernel cd0: <HSPA USB SCSI CD-ROM 6225> s/n 531399703502680 detached
Apr 16 16:51:19 kernel cd0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Apr 16 16:51:19 kernel umass0: at uhub1, port 1, addr 2 (disconnected)

I see it under Available network ports: as well. I will test in the evening if it works or not.

stephenw10

Ah, OK that's mostly all done then. Nice!

So yeah you can see that's a two line change to two files. Should be easy enough to replicate for the new ID.

Can you try this against your modem?
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=196362#c9

Does it then show up as ue0 as shown there?

Steve

stephenw10

Ah cross posted I see you did! Yeah see what happens when you assign it.

FreeBSD/pfSense handles serial port modems much better but the speed is limited there.

It would be interesting to see hoe usbconfig sees the modem when it's in Ethernet mode like that.

Steve

chedxb

I assigned as a new interface and then added usb_modeswitch -v 2001 -p a407 -m 1 -M 555342431234567800000000000003f0010300000000000000000000000000 -R 1 on
Shellcmd Configuration as earlyshellcmd and rebooted. So far so good :) I just need a SIM card to test the data connection.

stephenw10

The big problem with USB Ethernet type devices is that pfSense does not have any way to handle them disconnecting. If you reboot and unplug the modem pfSense will stop booting at the interfaces assign screen at the console because ue0 is no9 longer present on the system but is assigned in the config. There are workarounds but they are all hacky....

What speeds do you expect to get from that device?

Steve

chedxb

I am planning to use it as a backup connection. I will cap download 5Mbps and upload 1Mbps with Traffic Shaper.

Is it possible to put a timer for the interfaces? Say, if ue0 is not present for 10s, then continue booting without it.