NUT package (2.8.0 and below)

mrsunfire

No I was not. But now I am and it works flawless.

dennypage

@mrsunfire You cannot use apcupsd and nut at the same time. They cannot both manage system shutdown.

If you want help to understand the issue with nut, I will help you but you need to disable or delete apcupsd before proceeding.

Otherwise, if you are happy with using apcupsd, you should delete the nut package.

mrsunfire

Why? I just want the widget and nothing else. This works only with NUT and NUT only works with apcupsd right now :)
But yes, I want to find out what the problem is. I will do this tomorrow guided by your help.
Thanks in advance!

dennypage

@mrsunfire Because you cannot have two processes trying to manage system and ups shutdown/restart.

mrsunfire

I don't want to shutdown. I only want the widget. Is there a way to disable the shutdown completely?

dennypage

@mrsunfire Okay. When you are ready...

Remove the apcupsd package using the package manager (System / Package Manager / Installed Packages).
Go to the UPS configuration page (Services / UPS / Settings) and change the nut configuration to be:

UPS Type - Local USB
UPS Name - ups
Driver - usbhid
All other settings blank (empty).

Save the configuration.
Wait two minutes. Don't skip this step.
Check to confirm the service is not functioning by going to the UPS status page (Services / UPS / Status) and refreshing the browser. Assuming that the status page says that the ups requires attention...
Log into the system and run the nut startup script by hand:
```
/usr/local/etc/rc.d/nut.sh start
```
Post the output produced by the script, and the output from the system log when you ran the script. You can get the system log output with the following command:
```
clog /var/log/system.log | tail -25
```

which will display the last 25 lines of the system log.

mrsunfire

@dennypage said in NUT package:

OK, I've made all these steps:

Apr 18 21:51:54 pfsense upsmon[56145]: Startup successful
Apr 18 21:51:55 pfsense upsd[57066]: listening on ::1 port 3493
Apr 18 21:51:55 pfsense upsd[57066]: listening on 127.0.0.1 port 3493
Apr 18 21:51:55 pfsense upsd[57066]: Can't connect to UPS [UPS] (apcupsd-ups-UPS): No such file or directory
Apr 18 21:51:55 pfsense upsd[57261]: Startup successful
Apr 18 21:51:57 pfsense upsd[57261]: User local-monitor@::1 logged into UPS [UPS]
Apr 18 21:51:57 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:51:57 pfsense upsmon[56657]: Communications with UPS UPS lost
Apr 18 21:52:02 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:02 pfsense upsmon[56657]: UPS UPS is unavailable
Apr 18 21:52:07 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:12 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:13 pfsense login: login on ttyu0 as root
Apr 18 21:52:17 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:22 pfsense upsmon[56657]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:26 pfsense upsmon[19650]: Startup successful
Apr 18 21:52:27 pfsense upsd[20303]: listening on ::1 port 3493
Apr 18 21:52:27 pfsense upsd[20303]: listening on 127.0.0.1 port 3493
Apr 18 21:52:27 pfsense upsd[20303]: Can't connect to UPS [UPS] (apcupsd-ups-UPS): No such file or directory
Apr 18 21:52:27 pfsense upsd[20394]: Startup successful
Apr 18 21:52:29 pfsense upsd[20394]: User local-monitor@::1 logged into UPS [UPS]
Apr 18 21:52:29 pfsense upsmon[20188]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:29 pfsense upsmon[20188]: Communications with UPS UPS lost
Apr 18 21:52:34 pfsense upsmon[20188]: Poll UPS [UPS] failed - Driver not connected
Apr 18 21:52:34 pfsense upsmon[20188]: UPS UPS is unavailable

mrsunfire

OK strange, now I again uninstalled NUT and reinstalled it as previous but now it works!


Apr 18 21:56:36	upsd	71931	User local-monitor@::1 logged into UPS [UPS]
Apr 18 21:56:34	upsd	71931	Startup successful
Apr 18 21:56:34	upsd	71905	Connected to UPS [UPS]: usbhid-ups-UPS
Apr 18 21:56:34	upsd	71905	listening on 127.0.0.1 port 3493
Apr 18 21:56:34	upsd	71905	listening on ::1 port 3493
Apr 18 21:56:33	usbhid-ups	71892	Startup successful
Apr 18 21:56:33	upsmon	70877	Startup successful
Apr 18 21:56:33	php-fpm	30015	/nut_settings.php: Starting service nut

Without setting anything in the advanced options is there now a shutdown active?

dennypage

@mrsunfire Thank you for the system log output. Can you post the output from the script itself as well please?

Looking for something like this:

[2.4.4-RELEASE][root@fw]/root: sh -x /usr/local/etc/rc.d/nut.sh start
+ rc_start
+ echo starting NUT
starting NUT
+ /usr/bin/killall -q -9 upsmon
+ /usr/bin/killall -q -9 upsd
+ /usr/bin/killall -q -9 upsdrvctl
+ /usr/bin/killall -q -9 usbhid-ups
+ /usr/local/sbin/upsmon
Network UPS Tools upsmon 2.7.4
kill: No such process
UPS: ups (master) (power value 1)
Using power down flag file /etc/killpower
+ sleep 1
+ /usr/local/sbin/upsdrvctl start
Network UPS Tools - UPS driver controller 2.7.4
Network UPS Tools - Generic HID driver 0.41 (2.7.4)
USB communication driver 0.33
kill: No such process
Using subdriver: TrippLite HID 0.82
+ /usr/local/sbin/upsd -u root
Network UPS Tools upsd 2.7.4
kill: No such process
listening on ::1 port 3493
listening on 127.0.0.1 port 3493
Connected to UPS [ups]: usbhid-ups-ups
+ return 0
[2.4.4-RELEASE][root@fw]/root:

Alternatively, you could just start the driver:

[2.4.4-RELEASE][root@fw.cococafe.com]/root: /usr/local/sbin/upsdrvctl start
Network UPS Tools - UPS driver controller 2.7.4
Network UPS Tools - Generic HID driver 0.41 (2.7.4)
USB communication driver 0.33
Using subdriver: TrippLite HID 0.82
[2.4.4-RELEASE][root@fw.cococafe.com]/root:

dennypage

@mrsunfire said in NUT package:

OK strange, now I again uninstalled NUT and reinstalled it as previous but now it works!

Strange. Only thing I can think of here is that when nut is first installed, there are rules set up for ownership of the usb device so that nut can access it. These rules do have effect until the system is rebooted or the device is unplugged/replugged.

Without setting anything in the advanced options is there now a shutdown active?

Yes, if nut is running correctly you should be protected against the ups running out of battery.

mrsunfire

Where can I see the time when the system shutdown? Where to disable?

dennypage

@mrsunfire said in NUT package:

Where can I see the time when the system shutdown? Where to disable?

By default, nut initiates a shutdown when your ups declares a low battery situation. When this occurs varies from vendor to vendor and from ups to ups, usually based on battery size.
Note that you can generally override the ups defaults and have nut initiate the shutdown when X percentage of battery remains, or Y minutes of runtime remains.

Why do you want to disable shutdown? Managing shutdown is what nut exists for. Without it, you risk data corruption when the battery is exhausted. Also, the further you deplete the batter the higher the impact on long term battery health.

There is no "clean" way to disable shutdown. There are various tricks you can try, but they can leave either nut or the entire system inoperable without manual/physical intervention. And of course there is the risk of data corruption when power is lost.

Unless you have a super good reason to be trying to avoid shutdown, it's much better to let it do its thing.

mrsunfire

My board only auto boots after power lost. If the system shutdown, it doesn‘t boot after power is back.
Where can I set the battery low limit? With the apcupsd package this was possible.

dennypage

@mrsunfire said in NUT package:

My board only auto boots after power lost. If the system shutdown, it doesn‘t boot after power is back.

Your BIOS has power restore set to "Last State". Ideally for something like a firewall, the BIOS should be set for "Always On". If for some reason the BIOS doesn't have this ability, you can work around this with nut. Go to Advanced settings in the UPS configuration, and add the following line to the Additional configuration lines for upsmon.conf section:

SHUTDOWNCMD "/sbin/shutdown -h +0"

With this, nut will shut the system down but will not call for the system to power itself off. This will leave the system quiesced and data safe. Shortly thereafter (usually 20 seconds or so), the ups will kill the power. When the mains return, the ups will restore power and the system will automatically boot.

Where can I set the battery low limit? With the apcupsd package this was possible.

There are several discussions about affecting the low battery settings earlier in this thread. Look for override.battery.charge You can also see the ups.conf manual page. Use caution when changing these values. Unless you are trying to shorten run-time in order to preserve battery life, you are probably just fine with the default settings your ups provides.

mrsunfire

Thank you mate, you're awesome! Tomorrow I will replace my UPS. I use this as a test if the shutdown works as I want it and let you know if I'm happy with it.

mrsunfire

@dennypage said in NUT package:

clog /var/log/system.log | tail -25

OK, shutdown works perfect! The system also auto boots after power is back.

But after replacing the UPS with the same model and also installed the pfSense as UEFI new (restored backup) I again doesn't get connection to UPS.

I followed your steps. Here is the log:

Apr 20 14:36:50 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:36:55 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:00 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:05 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:10 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:15 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:20 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:25 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:30 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:35 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:41 pfsense upsmon[92951]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:41 pfsense upsmon[5675]: Startup successful
Apr 20 14:37:42 pfsense upsd[10577]: listening on ::1 port 3493
Apr 20 14:37:42 pfsense upsd[10577]: listening on 127.0.0.1 port 3493
Apr 20 14:37:42 pfsense upsd[10577]: Can't connect to UPS [UPS] (usbhid-ups-UPS): No such file or directory
Apr 20 14:37:42 pfsense upsd[10889]: Startup successful
Apr 20 14:37:44 pfsense upsd[10889]: User local-monitor@::1 logged into UPS [UPS]
Apr 20 14:37:44 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:44 pfsense upsmon[5937]: Communications with UPS UPS lost
Apr 20 14:37:49 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:49 pfsense upsmon[5937]: UPS UPS is unavailable
Apr 20 14:37:54 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:37:59 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:38:04 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected
Apr 20 14:38:09 pfsense upsmon[5937]: Poll UPS [UPS] failed - Driver not connected

mrsunfire

A reboot of the system fixed it!

rdborg

Hi i have a Galleon II rackmount 1kva, in NUT suppoted its listed as supported via usb and serial.. i have it hooked up up via usb but choosing the mentions drivers is not getting it to work... usb and interface work fine as it works well when tested with provided software on a windows machine... any ideas please??

dennypage

@rdborg did you reboot or unplug/re-plug after you installed nut?

rdborg

@dennypage that worked thanks bow one more question.. is there a way that the nut on pfsense acts as a sever for my other server in any way please?