Access printer from foreign network over IPSEC (multiple locations)

bashuis

should that like this?

pfsense01
172.16.0.0/24(local) --> 192.168.41.0/24(remote)

pfsense03
192.168.41.0/24(local) --> 172.16.0.0/24(remote)

conor

yes

bashuis

@conor
OK, i created the P2.
it is not UP, but that could be because there is no traffic going over it..

several other P2's over the samen P1 are online..

location 1 (pfsense01):

location 2 (pfsense02):

Should i disconnect and reconnect the whole IPSEC connection?

conor

on pfsense 02 for the sake of testing goto Firewall > Rules > IPSEC
add an allow all rule for this interface, you can fine tune it later this is just for testing

conor

@bashuis said in Access printer from foreign network over IPSEC (multiple locations):

Should i disconnect and reconnect the whole IPSEC connection?

if the down time isn't going to bother you probably best.

bashuis

@conor said in Access printer from foreign network over IPSEC (multiple locations):

sake of testing goto Firewall > Rules > IPSEC
add an allow all rule for this interface, you can fine tune it later this is just for testing

this rule was already active (for testing) on the IPSEC interface

conor

send a ping from the 172 network to the the printer ip in the 192 network, I'm half expecting this to fail, if it does check that you can still ping the 10.130.76.136 ip address.

bashuis

@conor said in Access printer from foreign network over IPSEC (multiple locations):

@bashuis said in Access printer from foreign network over IPSEC (multiple locations):

Should i disconnect and reconnect the whole IPSEC connection?

if the down time isn't going to bother you probably best.

@conor
that is not possible now, people are working over the other P2's

if it is needed i can shedule this later today/tonight

bashuis

@conor said in Access printer from foreign network over IPSEC (multiple locations):

send a ping from the 172 network to the the printer ip in the 192 network, I'm half expecting this to fail, if it does check that you can still ping the 10.130.76.136 ip address.

that is an problem, i have no access to the 172 network.

they started an permanent ping to 10.130.76.136 that i can use to debug.

i think we should NAT? 10.130.76.136 to 192.168.41.15

packet capturing on LAN2 (pfsense01) give now:
11:52:17.648234 IP 172.16.0.26 > 10.130.76.136: ICMP echo request, id 250, seq 37518, length 36
11:52:17.648254 IP 10.130.76.132 > 172.16.0.26: ICMP time exceeded in-transit, length 36

conor

@bashuis
correct, the customer router doesn't understand where the 192 is located, so a NAT is now needed, just enable the ICMP NAT first for testing.

conor

@bashuis said in Access printer from foreign network over IPSEC (multiple locations):

packet capturing on LAN2 (pfsense01) give now:
11:52:17.648234 IP 172.16.0.26 > 10.130.76.136: ICMP echo request, id 250, seq 37518, length 36
11:52:17.648254 IP 10.130.76.132 > 172.16.0.26: ICMP time exceeded in-transit, length 36

is that with the NAT?

bashuis

@conor said in Access printer from foreign network over IPSEC (multiple locations):

@bashuis said in Access printer from foreign network over IPSEC (multiple locations):

packet capturing on LAN2 (pfsense01) give now:
11:52:17.648234 IP 172.16.0.26 > 10.130.76.136: ICMP echo request, id 250, seq 37518, length 36
11:52:17.648254 IP 10.130.76.132 > 172.16.0.26: ICMP time exceeded in-transit, length 36

is that with the NAT?

no before.

i added this NAT rule on interface LAN2 on pfsense01

now i see the same:
11:54:49.664412 IP 172.16.0.26 > 10.130.76.136: ICMP echo request, id 250, seq 41040, length 36
11:54:49.664433 IP 10.130.76.132 > 172.16.0.26: ICMP time exceeded in-transit, length 36

conor

@bashuis
If the ping is failing before you add the NAT there still is the problem of pfsense01 to 172 to resolve, remove the NAT rule until that is resolved.

conor

can you send me the Routes for the pfsense01 please, Diagnostics > Routes

bashuis

@conor said in Access printer from foreign network over IPSEC (multiple locations):

can you send me the Routes for the pfsense01 please, Diagnostics > Routes

i see i have made an mistake in the ip's from the custommerrouter and LAN2 (switched, same lan). this is correct:

also added the new P2

we could also have a look with teamviewer/telephone if you like?