Watchguard Firebox M400/M500
-
@stephenw10
Do I understand that correctly: You tried to flash that BIOS file, the box rebooted twice and beeped a few times. But after it worked?Because when I tried the first time, I messed with the afudos parameters and bricked my box. So I had to use a SPI programmer to revive it...
-
Yes, sorry, that worked fine after going through it initialization routine because the cmos was cleared.
Steve
-
@zanthos
I just upgraded the RAM in my M400 with this one:
Kingston Value RAM KVR16N11K2/16 (2x8GB).
It works! -
Does anyone know what the power draw on these are roughly? I don’t have any way to measure mine but trying to spec a ups as the storm last night knocked power out and corrupted the install. Gonna have to pull the unit and reimage it but would like to prevent this going forward. My fault for not already having a ups but I can prevent it in the future.
-
~35W peak at boot then ~26W once booted and idle according to my plugin power meter.
Steve
-
@stephenw10
Thank you! -
Can anyone suggest a compatible replacement PSU? Can't find the exact model and similar FSP ones on ebay dont have the 8 pin motherboard connector.
-
You can get a 4pin to 8pin P4 adapter. Or you may not even need all 8 pins connected. There is no PCIe card in the M400 by default. I have not tried either personally.
Steve
-
@stephenw10 brilliant, never thought of an adapter. Thanks!
-
Just a bit of info which might help someone - this M400 happily took 2x 4Gb sticks of desktop RAM (Non ECC).
It was Hynix DDR3-1600 PC3-12800 (HP Branded - from an old PC a neighbour gave me to dispose of. Now wishing i hadn't sold the CPU!)
Hynix Part No HMT351U6CFR8C-PB
PS - if anyone needs an original 4 Gb ECC stick, let me know. (UK Ideally)
-
I wasn't able to get my M400 to boot successfully with a Xeon E3-1220l v3 CPU. I can hear 4 single beeps in quick succession during the boot process and then nothing past that point. Fans continue to run at full speed. I'm not sure if the CPU is bad or incompatible with my setup. I tried clearing the CMOS but that didn't help.
At this point I have reinstalled the Celeron and the box's back to where it was previously. Any suggestions on trouble shooting the box would be greatly appreciated. BTW, intel documentation indicate the C226 chipset is supposed to be compatible with the Xeon.
Thanks -
From Google..
"Four short beeps means that the motherboard timer is not working properly but it could also mean that there's an issue with the RAM module that's in the lowest (usually marked 0) slot. Usually, a hardware failure with an expansion card or an issue with the motherboard itself could be the cause of this beep code."
I suppose that could have to do with the CPU but check your RAM.
-
@chpalmer Thanks for that information, I did try reseating the RAM but it did not help. The same RAM works fine with the Celeron, so it appears the Xeon may be faulty or at least incompatible with the motherboard.
-
I had a couple M400's in hand and put pfsense on them for some friends. I didn't get to tinker however.
-
That Xeon has no graphics hardware. Might be an issue since the E3-1285 v3 is reported as working. Speculation at this point though.
Edit: Missed that this is the 1220L. Yeah that might require something a bit extra for it's very low speed and power.
Steve
-
@iJay-XTM5 Maybe Steve @stephenw10 is right about the missing gfx hardware.
You could try to disable it in the BIOS before swapping CPU's (Headless mode, no RAM assignment, ...).
At least in my unlocked BIOS I remember there should be an option to do so... -
@stephenw10 said in Watchguard Firebox M400:
That Xeon has no graphics hardware. Might be an issue since the E3-1285 v3 is reported as working. Speculation at this point though.
Edit: Missed that this is the 1220L. Yeah that might require something a bit extra for it's very low speed and power.
Steve
My apologies if I am not supposed to post links to an external site. Per this website -> https://www.thomas-krenn.com/en/wiki/AMI_BIOS_Beep_Codes
4 short beeps are supposed to be one of the following:- Wrong memory installed (eg. Registered when unbuffered required, or Non-ECC when ECC required)
- CPU not supported; update BIOS to support new CPU
I'll need to do a bit of digging to see if the RAM is incompatible. I am more inclined to believe #2 is more likely than #1. I'm going to request Lanner support for a copy of 7585's bios for now. Adding new CPU microcodes into the bios is beyond my capabilities so this may be the end of the road for this Xeon.
-
I guess it depends how 'short' they are.
Is it the original ram? The board does not support buffered DIMMs.I could well believe that ultra low power CPU requires a lower voltage than the board can provide though.
Steve
-
@stephenw10 Thanks for the additional information on the RAM. Unfortunately I did not time the beeps, but I estimate all 4 beeps used to take about 2 seconds.
I'm going to be brave and see what it takes to update the microcode within the bios!
-
@DeLorean
hello, everyone, I'm new here. can someone tell me why we can WatchGuard m200 box for Pfsense? here is what I have found so far on m200 so far
