IPV6 - pfsense behind BT Hub
-
@stephenw10 said in IPV6 - pfsense behind BT Hub:
Exactly the problem here is that the ISP routes the /56 PD to the BT Hub but since pfSense is not pullling a PD from the BT Hub it does not get the required route. So the BT Hub has no way to know the /64 on the pfSense LAN is behind a downstream router.
Unfortunately I doubt the BT business hub has any static routing, additional gateway type ability. I could be wrong...Steve
That's not the impression I got from the OP. He said:
"Thanks.
The BT Hub gets ipv6 via DHCPv6-PD on its WAN(2a0X:xxxx:xxxx:xx00:86a1:d1ff:fea1:f0df) BUT gave Pfsense WAN a
fe80:: range ,WHICH i then changed to(2a0X:xxxx:xxxx:xx00:86a1:d1ff:fea1:f0ff /64 - STATIC) and used the Other /64 on the pfsense LAN side.
The Default routes on the LAN clients is showing as fe80::,(EXpecting the LAN v6 gateway?) but ipv6 client is in the right range ,also DNS is Pfsense LAN ipv6 gateway and Google v6 dns."Based on that, it appears that he is being assigned a prefix, but not a WAN address. That is entirely normal, as the link local address will be used for routing and a WAN address is not necessary. He has the same thing on the LAN, with the link local address being used for the gateway. This is entirely normal. Based on what I've read in this thread is he can't reach the Internet from his LAN, which indicates a routing problem or perhaps a misconfigured firewall.
-
Indeed, BT don't usually give you a WAN IP just a Prefix. That's exactly what I see on my BT connection.
But unlike the OP I am using pfSense to get that prefix, he is using the BT Hub router. I am setting up a PD in that edge pfSense device to pass a /60 to my inner pfSense device. He is just configuring it statically on pfSense with no way to tell the BT Hub about that route.
Steve
-
@JKnott
Will try the Capture and see what i find
Regards -
Is there any ability to add routes and gateways in the BT Business hub?
-
Yes exactly ,but i was expecting the BT hub to give Pfsence an ip in the 2a0X:xxxx:xxxx:xx00:: /64 but it wasnt but gave it a fe80:: ?? will try to keep this as fe80:: and then use the /64 from the BT wan range in the LAN ,BUT that will still pose the issue of the BT box knowing how to get to this /64.
-
@stephenw10
Will look into this by weekend,so set a static route(BT hUB) for the /64 to the pfsense WAN (fe80::)?? -
Yes I would expect that to work. Odd that it doesn't assign the pfSense WAN a routable v6 IP though, it's set to DHCPv6? I assume other devices connected to the hub do get a v6 IP in that /64?
-
@stephenw10 said in IPV6 - pfsense behind BT Hub:
he is using the BT Hub router
I didn't see that. In that case prefix delegation won't work. He wants to put the modem in bridge mode. With it in gateway mode, only devices connected directly to it will get an address.
-
@Jid said in IPV6 - pfsense behind BT Hub:
Yes exactly ,but i was expecting the BT hub to give Pfsence an ip in the 2a0X:xxxx:xxxx:xx00:: /64 but it wasnt but gave it a fe80:: ?? will try to keep this as fe80:: and then use the /64 from the BT wan range in the LAN ,BUT that will still pose the issue of the BT box knowing how to get to this /64.
If that modem is in gateway mode, you can't put pfSense behind it and expect it to work properly. The pfSense WAN interface should get an address, but no prefix for the LAN. Every IPv6 capable device will have a link local fe80 address, no matter what it's connected to. That does not come from the ISP. It's often derived from the MAC address.
-
@JKnott
"With it in gateway mode, only devices connected directly to it will get an address". That is the case here .
The Probem is HOW do I get Devices on LAN side of Pfsense(connected directly to BT hub) to be able to route out in ipv6. -
Yes they do in the 2a0X:xxxx:xxxx:xx00:: range, however in the pfsense WAN(directly connected to LAN of BT Hub) its showing in the fe80:: range.
-
Some sort of route on the BT Hub, static or added via a PD.
Or put the hub in modem mode and just use pfSense directly.
I know the Business hub used to do something funky with static IPv4 subnets though that caused problems with that.
-
What is the pfSense WAN set to for IPv6? Or what was it set to before you set it statically?
If dhcpv6 doesn't work try SLAAC.
Steve
-
@stephenw10
DHCPV6 it gets fe80:: range , Static applied 2a0X:xxxx:xxxx:xx00:: /64 to match the 2a0X:xxxx:xxxx:xx00:: on the BT hub. -
@stephenw10
Just tried SLAAC and getting this fdaa:bbcc:ddee:0:215: is that good.
But i cant access any Node to test now . -
If other clients connected to the Hub do get an IPv6 IP as expected, what are they set to?
That address with SLACC is not any better really.
-
Thanks ,Stv unfortunateley no device is currently connected to LANof BT hub ,apart from Pfsense.
-
@Jid
Tried DHCPv6 now getting this fdaa:bbcc:ddee: ?
For the LAN side what should it ? Statics? with DHCPv6 active? -
I expect dhcpv6 to pull an routable v6 IP from a /64 withing the /56 BT are delegating to you.
I think you probably need to confirm a laptop connected to the Hub is getting that before going further here.
Steve
-
BT Hub IPv6 status:
EnabledIPv6 network status:
EnabledIPv6 WAN details
Global unicast address:
2a00:xxxx:xxxx:x801:86a1:d1ff:fea1:f0ddGlobal unicast prefix/length:
2a00:xxxx:xxxx:x801::/64Link local address:
fe80::86a1:d1ff:fea1:f0ddRemote link local address:
fe80::1e6a:7aff:fe68:f00DNS:
Not availableIPv6 LAN details
Global unicast address:
2a00:xxxx:xxxx:x800:86a1:d1ff:fea1:f0dfULA prefix / length:
fdaa:bbcc:ddee::/64Link local address:
fe80::86a1:d1ff:fea1:f0dfPfsense Status:
WAN : fdaa:bbcc:ddee:0:215:5dff:feb8:ea10 9 (DhcpV6)
LAN: 2a00:xxxx:xxxx:x802:87a1:d1ff:fea1:1000 /64 (Static)
Dhcpv6 server (enabled)
Range: 2a00:xxxx:xxxx:x802::100 to 2a00:xxxx:xxxx:x802::250 (PC are getting this range)
RA: RouterMOde Assisted.
Priority Normal
DNS Config. : 2001:4860:4860::8888Is any thing unusual here?
