Watchguard XTM 5 Series
-
If you can find one you might try an old NanoBSD serial image directly on the CF card. There are still some mirrors out there hosting them even though they shouldn't be.
Steve
-
I have now tried versions 2.3.5 in both amd64 and i386 and both freeze at the same point as version 2.4.4 I have also tried removing some memory and moving it between banks.
I have also tried to boot the old CF card I used to flash the x550 bios, not to use on this bios but just to see if I can get a dos prompt but again all I get is garbage once past the post screen.
I suspect I need to flash the bios but how can I do this if nothing will load? Failing that I think my box may be a dud :-(
Can't think of anything else left to try now.
Luke
-
@stephenw10 Would this be the right one to try pfSense-CE-2.3.5-RELEASE-4g-i386-nanobsd.img.gz it doesn't say serial but some of the others do say VGA?
The previous versions I have tried have all been memstick versions
Thanks
Luke -
Yes, that would do it. As long as the CF card is 4GB or bigger.
-
It's an odd place to stop. For reference on mine at that point:
fxp0: Ethernet address: 00:90:7f:87:dc:74 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ahci0: <Intel ICH7 AHCI SATA controller> port 0x7c00-0x7c07,0x7880-0x7883,0x7800-0x7807,0x7480-0x7483,0x7400-0x740f mem 0xfe4ffc00-0xfe4fffff irq 19 at device 31.2 on pci0 ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 acpi_button0: <Power Button> on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: console (115200,n,8,1) uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0The SATA controller is running in AHCI mode so it shows slightly differently to yours.
The next thing that shows is the power button (is yours stuck maybe?) but then the console....Can you interrupt it at the boot loader menu to reach the loader prompt?
If it has some console problem you might try forcing VGA console. You will get no output but it should still boot completely allowing you webgui access.
Steve
-
@stephenw10 Hi Steve, I tried the nanobsd last night and it stuck it exactly the same place, can you give a little more detail on how to force the VGA method please.
Thanks
Luke -
@stephenw10 Should have added both internal and external power buttons can turn the unit on and off ok. Could you clarify what jumpers you have in place please?
Thanks
Luke -
Booting to VGA console as primary:
https://docs.netgate.com/pfsense/en/latest/hardware/boot-troubleshooting.html#booting-with-an-alternate-consoleYou should still hear the boot tune if it is able to fully boot using that.
Steve
-
@stephenw10 Hi Steve, apologies for the delay in coming back to you. Well I have tried the VGA boot with no joy I have also tried all the other settings such as safe mode, verbose, single user, all with no joy and all stop at the same place. I have also tried booting with no console cable attached, nothing good.
The seller I bough from ebay has other units for auction so have contacted him about purchasing a second unit to confirm if unit number one is faulty as they have a returns policy so could return it.
-
Try hooking a sata drive up to it and see if it will load that way.
-
@chpalmer Yep that's what I have done, installed sata drive in a VM and confirmed it boots without any prompts, but in the XTM I get the freeze at the same place with versions 2.4.4, 2.3.5, i386, amd64, nanobsd, memstick, on CF or SATA
-
Hmm, but you were able to interrupt the boot loader and enter characters which implies the console is working fine at that point. Hard to say then, I don't recall anything stopping at that point previously.
Steve
-
hello,
first very impressed of the activity for this redbox AND pfsense : woahhhh !
secondly :
i have 3 of thix box running fine for a long time.
But with a fourth, i just buy , big problem.
motherboard is FW-7580 W REV 1.01 - i can't install if not flashing to xtm5_83.rom : i need to pass ATA from IDE to AHCI , why ?
2 - but with new BIOS (Pfsense 1.8) : just LAN NIC is working all other can't acces WAN (internet)
3 - how can i come back to my bios backup ? (if no web access , for downloading flashrom ... obtain flashrom binary, and install how to do that ?!!)i really need your help !
-
So only the fxp port is working?
You can still set that as the WAN and use that to pull in flashrom. If you only have one port defined it will be WAN.
Were the other ports working before you flashed the BIOS? I have never seen that be an issue. I'm not sure how it would break the NICs. Unless that board is completely different, which seems unlikely.
Steve
-
@stephenw10
hello stephnew10 : happy to see you here !!!
What a marvellous adventure pfsense on Watchguard . pfffiiiouuuu ;-)Yep with bios WG 1.3 , just laste nic em5 was probably out of order.
But with xtm5_83.rom ... lol !
just one. -
Hmm, well hard to explain how that could be. It would be good to know which one still works. I'm guessing it's the 100M port (fxp0) since that's completely different.
Whichever it is you should be able to use it as WAN to connect out and install flashrom.Steve
-
@stephenw10
hello, sorry for delay.root@OPNsense:~ # pkg install flashrom Updating OPNsense repository catalogue... Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: pkg: https://pkg.opnsense.org/FreeBSD:11:amd64/20.1/latest/meta.txz: Authentication error repository OPNsense has no meta file, using default settings Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: Certificate verification failed for /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 2813191321208:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/usr/src/crypto/openssl/ssl/s3_clnt.c:1269: pkg: https://pkg.opnsense.org/FreeBSD:11:amd64/20.1/latest/packagesite.txz: Authentication error Unable to update repository OPNsense Error updating repositories! -
@ledufakademy said in Watchguard XTM 5 Series:
Unable to update repository OPNsense
Your not running pfsense. Without knowing the particulars of that product nobody here would be able to guess correctly.
-
-
@stephenw10
ok i will flash the card F with last pfsense
with pfsense : boot stuck at :
em5: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci2 : solved.
same issue :
[2.4.3-RELEASE][root@pfSense.localdomain]/root: pkg update Updating pfSense-core repository catalogue... pkg: Repository pfSense-core load error: access repo file(/var/db/pkg/repo-pfSense-core.sqlite) failed: No such file or directory Certificate verification failed for /C=GB/ST=Greater Manchester/L=Salford/O=Sectigo Limited/CN=Sectigo RSA Domain Validation Secure Server CA 34405266376:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/builder/ce-243/tmp/FreeBSD-src/crypto/openssl/ssl/s3_clnt.c:1269: pkg: https://pkg.pfsense.org/pfSense_v2_4_3_amd64-pfSense_v2_4_3/packagesite.txz: Authentication error Unable to update repository pfSense Error updating repositories!
