Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    [SOLVED] First installation, but PC no longer connects

    Scheduled Pinned Locked Moved Problems Installing or Upgrading pfSense Software
    30 Posts 4 Posters 3.4k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • W
      WhiteTiger-IT @Gertjan
      last edited by WhiteTiger-IT

      @Gertjan
      As I wrote, it works neither with DHCP nor with static IP.
      Obviously with the static IP the values IP, Mask, DNS and Gateway are correct.

      As for the assignment of the interfaces it is not difficult.
      I disconnect the three cables, launch the "auto" and then connect the single cable.
      This is for each one of the three cables.

      The red cable goes to the router.
      The green cable goes to the switch where the two PCs are connected
      The yellow cable goes to a second switch where nothing is currently connected.

      So, I can't go wrong, nor do I assign cables to the interfaces, nor do I assign cables to the router and the two switches.

      During the various installations I made, however, I noticed that pfSense randomly assigns the re0, re1, re2 cards.
      Once they are connected in one way and another time they are connected in a different way.
      I am therefore obliged to do the manual assignment to avoid problems and confusion.
      For this reason I am sure that the assignment is correct.

      ==== Update ====
      I solved the problem.

      On the PC of pfSense I installed Xubuntu indicating to take the whole disk.
      Then I installed pfSense again, always taking the whole disk.
      Now I can connect to 192.168.1.1

      I wonder if with the first installation something was saved that then remained on the disk even with the "reset to default factory" and with the (old) new installation of pfSense.
      Something that has been erased using the entire disk for something else, Xubuntu in my case.

      Or is it just a coincidence?

      GertjanG 1 Reply Last reply Reply Quote 0
      • GertjanG
        Gertjan @WhiteTiger-IT
        last edited by Gertjan

        @WhiteTiger-IT said in First installation, but PC no longer connects:

        During the various installations I made, however, I noticed that pfSense randomly assigns the re0, re1, re2 cards.
        Once they are connected in one way and another time they are connected in a different way.
        I am therefore obliged to do the manual assignment to avoid problems and confusion.
        For this reason I am sure that the assignment is correct.

        Scary.
        If the kernel detects interface on a subsequent boot in another order : then known interfaces will get assigned teh other way around. LAN becomes WAN ,etc which is a big security issue.
        Such a situation should never happen.

        But you're using "re" or Raaeltek NIC's. This forum is loaded with issues with NIC's : mostly Realtek ones, they are are then famous for this.

        @WhiteTiger-IT said in First installation, but PC no longer connects:

        On the PC of pfSense I installed Xubuntu indicating to take the whole disk.
        Then I installed pfSense again, always taking the whole disk.

        I guess it's possible to make the pfSense device a dual boot device.
        The manual doesn't speak a word about it. I didn't even know people did such a thing.
        Ones it own it's has it's own file system. pfSense doesn't look in other file system for it's settings, it isn't even aware that they exist.
        As long as it boot, it should be fine.

        @WhiteTiger-IT said in First installation, but PC no longer connects:

        Obviously with the static IP the values IP, Mask, DNS and Gateway are correct

        Great.
        Understand that I had to ask.
        Most people that install pfSense understand what an Ip is.
        But masks (networks) , gateway etc : they are less known.
        Like the famous : I set up my pfSense LAN to /32 (was /24) and now DHCP doesn't work ....

        No "help me" PM's please. Use the forum, the community will thank you.
        Edit : and where are the logs ??

        1 Reply Last reply Reply Quote 0
        • W
          WhiteTiger-IT @Gertjan
          last edited by

          @Gertjan
          It happened again!
          I have made a new installation.

          From my browser I connected and arrived at the login page.
          I did not enter and I turned off my PC; then, from the console of pfSense, I selected 6) Halt System.

          Return to the office.
          I turn on pfSense and once it is started, I turn on my PC, try the connection again and it gives me an error.
          From the moment of installation to now I have only turned off pfSense with the Halt System command.

          This is the photo taken on the pfSense PC after the installation.
          After installation there is an error message.
          Alt-Install
          This is the photo taken on the pfSense PC now
          pfSense-Now
          This is the photo taken on the switch with only the two cables involved.
          Switch
          And this is the snapshoot of the IPv4 configurations of my PC.
          alt text

          1 Reply Last reply Reply Quote 0
          • GertjanG
            Gertjan
            last edited by Gertjan

            During boot, look at boot console screen.
            At the end - you'll see the menu.

            Use option 8 and command

            ifconfig
            

            compare mac addresses with interface / driver names = pfSense interfaces.
            be sure they are not mixed up.

            If your LAN became WAN , then all explains.

            edit : when you set up a static IP on your PC, do not omit the Gateway - neither the DNS. You have to fill them in.
            "192.168.1.1" for both. These 2 are not really optional.

            No "help me" PM's please. Use the forum, the community will thank you.
            Edit : and where are the logs ??

            W 1 Reply Last reply Reply Quote 0
            • V
              valentinius
              last edited by

              seccion reply lists seem to be useful for me, i dont remember where i saw them

              1 Reply Last reply Reply Quote 0
              • W
                WhiteTiger-IT @Gertjan
                last edited by WhiteTiger-IT

                @Gertjan said in First installation, but PC no longer connects:

                During boot, look at boot console screen.
                At the end - you'll see the menu.

                Use option 8 and command

                ifconfig
                

                compare mac addresses with interface / driver names = pfSense interfaces.
                be sure they are not mixed up.

                If your LAN became WAN , then all explains.

                edit : when you set up a static IP on your PC, do not omit the Gateway - neither the DNS. You have to fill them in.
                "192.168.1.1" for both. These 2 are not really optional.

                Sorry, but are you telling me that during boot pfSense swaps the WAN with the LAN?
                If true it is crazy!
                At this point pfSense becomes totally useless because it is unmanageable.
                Since there are thousands of them installed, I would like to understand why this only happens to mine.

                Finally, I know that I have to put gateways and DNS on my PC, but if I want to surf with Wi-Fi I can't put them because there is already the gateway to this.

                === Update ===
                From Xubuntu I deleted the partition on the disk and then I made a new fresh installation of pfSense.
                Now I have arrived again at the login page and this time turning off and on I can still get to the login page.
                I try again to do the configuration and we will see if it still works tomorrow morning.
                Otherwise I don't know what to think anymore, except to blame the green goblins

                For the moment, thank you

                1 Reply Last reply Reply Quote 1
                • W
                  WhiteTiger-IT
                  last edited by WhiteTiger-IT

                  It is simply ridiculous!
                  It was not possible that last evening it worked and this morning it no longer works!

                  Whatever the change that bothered it.
                  It cannot work at the time of the save and not work the next day.

                  And then what bothers?
                  I haven't even created a rule. I haven't even changed the interface configuration. Not even the name OPT1.
                  I changed the Dashboard, activated PowerSaving, created two users

                  GertjanG 1 Reply Last reply Reply Quote 1
                  • GertjanG
                    Gertjan @WhiteTiger-IT
                    last edited by

                    This :

                    @WhiteTiger-IT said in First installation, but PC no longer connects:

                    last evening it worked and this morning it no longer works!

                    is close-to-none error description.

                    Something in the logs at the moment of change ?
                    Did it reboot ?
                    Did you check the interfaces ?

                    @WhiteTiger-IT said in First installation, but PC no longer connects:

                    created two users

                    It's a firewall. Two users ? You need two admins ?

                    No "help me" PM's please. Use the forum, the community will thank you.
                    Edit : and where are the logs ??

                    W 1 Reply Last reply Reply Quote 0
                    • W
                      WhiteTiger-IT @Gertjan
                      last edited by WhiteTiger-IT

                      Everything closed at 12:45. At 16:00 I turn on and once again nothing works.
                      It was configured with DHCP and instead I am forced to put the Static IP on the PC, but even so it is not reachable.
                      There is no ping between PC and pfSense, nor between pfSense and PC.

                      If I don't log in, where can I find the logs?

                      @Gertjan said in First installation, but PC no longer connects:

                      is close-to-none error description.

                      So what?

                      Did you check the interfaces ?

                      The interfaces are correctly assigned to their respective MAC addresses, there has been no swap.
                      If they are working obviously I don't know.
                      The leds on the cards and on the switch work.

                      It's a firewall. Two users ? You need two admins ?

                      There are three users, two admin. I'm only using user "admin", but if I don't even get to the login page it's useless to talk about it.

                      GertjanG 1 Reply Last reply Reply Quote 0
                      • GertjanG
                        Gertjan @WhiteTiger-IT
                        last edited by

                        @WhiteTiger-IT said in First installation, but PC no longer connects:

                        So what?

                        I'm trying to understand what can happen.
                        I can shut my pfSense, and start it right away, or hours /days later, and it will humm on as before.
                        You probably believe me that this happens with many others (although, most of do not shut the system down often).

                        So what so special about your settings and/or device, knowing that the code base is the same.

                        @WhiteTiger-IT said in First installation, but PC no longer connects:

                        If I don't log in

                        God mode always works ☺ The console access : the most important access because it's dedicated to those times when things go down hill.

                        I'm curious to see - from the console - a boot when all goes well, and one when the system goes 'freeze'.

                        No "help me" PM's please. Use the forum, the community will thank you.
                        Edit : and where are the logs ??

                        W 1 Reply Last reply Reply Quote 0
                        • W
                          WhiteTiger-IT
                          last edited by

                          These are the steps during and after installation.
                          I don't find anything particular or wrong with what I have done.

                          PfSense installation

                          • Installation from USB stick
                          • Interface assignment
                            (remove the cable from the boards, choose Auto and insert the corresponding cable)
                          • Assign addresses
                          • Yes for reverting to WebConfigurator
                          • DHCP for LAN and OPT1
                          • Continue from browser (admin / pfsense)
                          • Complete the Wizard
                          • Check for updates
                          • In System / General Setup:
                            ** change the columns of the Dashboard to 3
                            ** Top Navigation on "Fixed"
                          • First configuration of the Dashboard

                          Done Backup -1-Post Installation

                          Advanced configuration

                          • In System / Advanced / Admin Access / WebConfigurator
                            ** Select HTTPS
                            ** WebConfigurator / TCP port = 1020
                            ** DO NOT enable WebGUI redirect (I tried also with enabled)
                            ** Enable Browser tab text
                            ** Enable Secure Shell on port 222
                          • In System / Advanced / Networking
                            ** Disable IPV6
                          • In System / Advanced / Miscellaneous
                            ** Power Savings Activate Enable PowerD
                            ** Cryptographic & Thermal Hardware / Thermal Sensors = Intel CPU
                            ** NO! Hardware Settings / Hard disk standby time = 12 (I tried with this settings)

                          Done Backup -2-Advanced-Config

                          User Management

                          • In System / User Manager
                            ** Creation of SysManager group / Users "admin" with fewer rights
                            ** Privilege assignment
                            *** User - Notices: View
                            *** WebCfg - Crash reporter
                            *** WebCfg - Diagnostics
                            *** WebCfg - Status
                          • User creation and association to groups
                            ** Enable Custom Settings and specify:
                            *** Top Navigatuon on "Fixed"
                            *** 3 columns in Dashnboard
                            *** Browser tab text = "Display page name first in browser tab"

                          Done Backup -3-UserManagement

                          1 Reply Last reply Reply Quote 0
                          • W
                            WhiteTiger-IT @Gertjan
                            last edited by

                            @Gertjan
                            Thank you for your interest and help.
                            I am aware that the problem is here, with my pfSense.

                            I don't understand what you mean by "close-to-none".
                            If you tell me where I find the log from the console, I'll go and see it

                            GertjanG 1 Reply Last reply Reply Quote 0
                            • GertjanG
                              Gertjan @WhiteTiger-IT
                              last edited by Gertjan

                              @WhiteTiger-IT said in First installation, but PC no longer connects:

                              "close-to-none"

                              "we" as a forum audience like to "see" things.

                              Like :

                              Console or SSH access : I's using SSH because all is fine now :

                              Using username "admin".

                              Authenticating with public key "rsa-key-20190201"
                              Passphrase for key "rsa-key-20190201":
                              pfSense - Netgate Device ID: 195fccaad82dc1d68d5f
                              
                              *** Welcome to pfSense 2.4.5-RELEASE-p1 (amd64) on pfsense ***
                              
                               WAN (wan)       -> em3        -> v4/DHCP4: 192.168.10.2/24
                               LAN (lan)       -> em1        -> v4: 192.168.1.1/24
                                                                v6: 2001:470:1e13:5d0:2::1/64
                               PORTAL (opt1)   -> fxp0       -> v4: 192.168.2.1/24
                               HENETV6 (opt2)  -> gif0       -> v6: 2001:470:1e12:5d0::2/128
                               EXPRESS (opt3)  -> ovpnc2     ->
                               OPENVPN (opt4)  -> ovpns1     -> v4: 192.168.3.1/24
                                                                v6: 2001:470:bce0:3::1/64
                              
                               0) Logout (SSH only)                  9) pfTop
                               1) Assign Interfaces                 10) Filter Logs
                               2) Set interface(s) IP address       11) Restart webConfigurator
                               3) Reset webConfigurator password    12) PHP shell + pfSense tools
                               4) Reset to factory defaults         13) Update from console
                               5) Reboot system                     14) Disable Secure Shell (sshd)
                               6) Halt system                       15) Restore recent configuration
                               7) Ping host                         16) Restart PHP-FPM
                               8) Shell
                              
                              Enter an option: 8
                              
                              [2.4.5-RELEASE][admin@pfsense.brit-hotel-fumel.net]/root: dmesg
                              Copyright (c) 1992-2020 The FreeBSD Project.
                              Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
                                      The Regents of the University of California. All rights reserved.
                              FreeBSD is a registered trademark of The FreeBSD Foundation.
                              FreeBSD 11.3-STABLE #243 abf8cba50ce(RELENG_2_4_5): Tue Jun  2 17:53:37 EDT 2020
                                  root@buildbot1-nyi.netgate.com:/build/ce-crossbuild-245/obj/amd64/YNx4Qq3j/build/ce-crossbuild-245/sources/FreeBSD-src/sys/pfSense amd64
                              FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
                              VT(vga): resolution 640x480
                              CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.07-MHz K8-class CPU)
                                Origin="GenuineIntel"  Id=0xf43  Family=0xf  Model=0x4  Stepping=3
                                Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
                                Features2=0x649d<SSE3,DTES64,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
                                AMD Features=0x20100800<SYSCALL,NX,LM>
                                TSC: P-state invariant
                              real memory  = 2147483648 (2048 MB)
                              avail memory = 2005266432 (1912 MB)
                              Event timer "LAPIC" quality 100
                              ACPI APIC Table: <DELL   DM051  >
                              FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
                              FreeBSD/SMP: 1 package(s) x 2 hardware threads
                              ioapic0: Changing APIC ID to 8
                              ioapic0 <Version 2.0> irqs 0-23 on motherboard
                              SMP: AP CPU #1 Launched!
                              Timecounter "TSC-low" frequency 1596034060 Hz quality 1000
                              random: entropy device external interface
                              wlan: mac acl policy registered
                              kbd1 at kbdmux0
                              000.000022 [4213] netmap_init               netmap: loaded module
                              module_register_init: MOD_LOAD (vesa, 0xffffffff812d9960, 0) error 19
                              mlx5en: Mellanox Ethernet driver 3.5.2 (September 2019)
                              nexus0
                              vtvga0: <VT VGA driver> on motherboard
                              cryptosoft0: <software crypto> on motherboard
                              padlock0: No ACE support.
                              acpi0: <DELL DM051  > on motherboard
                              acpi0: Power Button (fixed)
                              cpu0: <ACPI CPU> on acpi0
                              cpu1: <ACPI CPU> on acpi0
                              atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
                              atrtc0: registered as a time-of-day clock, resolution 1.000000s
                              Event timer "RTC" frequency 32768 Hz quality 0
                              attimer0: <AT timer> port 0x40-0x5f irq 0 on acpi0
                              Timecounter "i8254" frequency 1193182 Hz quality 0
                              Event timer "i8254" frequency 1193182 Hz quality 100
                              Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
                              acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
                              hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
                              Timecounter "HPET" frequency 14318180 Hz quality 950
                              Event timer "HPET" frequency 14318180 Hz quality 450
                              Event timer "HPET1" frequency 14318180 Hz quality 440
                              Event timer "HPET2" frequency 14318180 Hz quality 440
                              acpi_button0: <Power Button> on acpi0
                              pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
                              pci0: <ACPI PCI bus> on pcib0
                              pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
                              pci1: <ACPI PCI bus> on pcib1
                              vgapci0: <VGA-compatible display> port 0xecd8-0xecdf mem 0xeff00000-0xeff7ffff,0xd0000000-0xdfffffff,0xefec0000-0xefefffff irq 16 at device 2.0 on pci0
                              agp0: <Intel 82945G (945G GMCH) SVGA controller> on vgapci0
                              agp0: aperture size is 256M, detected 7932k stolen memory
                              vgapci0: Boot video device
                              vgapci1: <VGA-compatible display> mem 0xeff80000-0xefffffff at device 2.1 on pci0
                              hdac0: <Intel 82801G HDA Controller> mem 0xefebc000-0xefebffff irq 16 at device 27.0 on pci0
                              pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
                              pcib2: [GIANT-LOCKED]
                              uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xff80-0xff9f irq 21 at device 29.0 on pci0
                              usbus0 on uhci0
                              usbus0: 12Mbps Full Speed USB v1.0
                              uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xff60-0xff7f irq 22 at device 29.1 on pci0
                              usbus1 on uhci1
                              usbus1: 12Mbps Full Speed USB v1.0
                              uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
                              usbus2 on uhci2
                              usbus2: 12Mbps Full Speed USB v1.0
                              uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xff20-0xff3f irq 23 at device 29.3 on pci0
                              usbus3 on uhci3
                              usbus3: 12Mbps Full Speed USB v1.0
                              ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xffa80800-0xffa80bff irq 21 at device 29.7 on pci0
                              usbus4: EHCI version 1.0
                              usbus4 on ehci0
                              usbus4: 480Mbps High Speed USB v2.0
                              pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
                              pci2: <ACPI PCI bus> on pcib3
                              em0: <Intel(R) PRO/1000 Legacy Network Connection 1.1.0> port 0xd8c0-0xd8ff mem 0xef980000-0xef99ffff,0xefa00000-0xefa3ffff irq 18 at device 2.0 on pci2
                              em0: Ethernet address: 6c:b3:11:50:c6:c6
                              em0: netmap queues/slots: TX 1/256, RX 1/256
                              em1: <Intel(R) PRO/1000 Legacy Network Connection 1.1.0> port 0xdc00-0xdc3f mem 0xef9a0000-0xef9bffff,0xefa40000-0xefa7ffff irq 19 at device 2.1 on pci2
                              em1: Ethernet address: 6c:b3:11:50:c6:c7
                              em1: netmap queues/slots: TX 1/256, RX 1/256
                              em2: <Intel(R) PRO/1000 Legacy Network Connection 1.1.0> port 0xdc40-0xdc7f mem 0xef9c0000-0xef9dffff,0xefa80000-0xefabffff irq 19 at device 3.0 on pci2
                              em2: Ethernet address: 00:1b:21:32:da:42
                              em2: netmap queues/slots: TX 1/256, RX 1/256
                              em3: <Intel(R) PRO/1000 Legacy Network Connection 1.1.0> port 0xdc80-0xdcbf mem 0xef9e0000-0xef9fffff,0xefac0000-0xefafffff irq 16 at device 3.1 on pci2
                              em3: Ethernet address: 00:1b:21:32:da:43
                              em3: netmap queues/slots: TX 1/256, RX 1/256
                              fxp0: <Intel 82801GB (ICH7) 10/100 Ethernet> port 0xdcc0-0xdcff mem 0xef97f000-0xef97ffff irq 20 at device 8.0 on pci2
                              miibus0: <MII bus> on fxp0
                              inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0
                              inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
                              fxp0: Ethernet address: 00:12:3f:b3:58:75
                              isab0: <PCI-ISA bridge> at device 31.0 on pci0
                              isa0: <ISA bus> on isab0
                              atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0
                              ata0: <ATA channel> at channel 0 on atapci0
                              atapci1: <Intel ICH7 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfea0-0xfeaf irq 20 at device 31.2 on pci0
                              ata2: <ATA channel> at channel 0 on atapci1
                              ata3: <ATA channel> at channel 1 on atapci1
                              orm0: <ISA Option ROMs> at iomem 0xc0000-0xca7ff,0xca800-0xcb7ff,0xcb800-0xcc7ff,0xcc800-0xce7ff,0xce800-0xcffff on isa0
                              atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
                              atkbd0: <AT Keyboard> irq 1 on atkbdc0
                              kbd0 at atkbd0
                              atkbd0: [GIANT-LOCKED]
                              ppc0: cannot reserve I/O port range
                              est0: <Enhanced SpeedStep Frequency Control> on cpu0
                              est: CPU supports Enhanced Speedstep, but is not recognized.
                              est: cpu_vendor GenuineIntel, msr 102d0000102d
                              device_attach: est0 attach returned 6
                              est1: <Enhanced SpeedStep Frequency Control> on cpu1
                              est: CPU supports Enhanced Speedstep, but is not recognized.
                              est: cpu_vendor GenuineIntel, msr 102d0000102d
                              device_attach: est1 attach returned 6
                              Timecounters tick every 1.000 msec
                              hdacc0: <Sigmatel STAC9221 HDA CODEC> at cad 0 on hdac0
                              hdaa0: <Sigmatel STAC9221 Audio Function Group> at nid 1 on hdacc0
                              pcm0: <Sigmatel STAC9221 (Rear Analog 5.1 Speaker)> at nid 13,15,12 on hdaa0
                              ugen4.1: <Intel EHCI root HUB> at usbus4
                              uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
                              ugen0.1: <Intel UHCI root HUB> at usbus0
                              uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
                              ugen3.1: <Intel UHCI root HUB> at usbus3
                              uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
                              ugen2.1: <Intel UHCI root HUB> at usbus2
                              uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
                              ugen1.1: <Intel UHCI root HUB> at usbus1
                              uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
                              ata0: timeout waiting for read DRQ
                              (aprobe0:ata0:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 00 00 00
                              (aprobe0:ata0:0:1:0): CAM status: CCB request completed with an error
                              (aprobe0:ata0:0:1:0): Retrying command
                              uhub1: 2 ports with 2 removable, self powered
                              uhub2: 2 ports with 2 removable, self powered
                              uhub3: 2 ports with 2 removable, self powered
                              uhub4: 2 ports with 2 removable, self powered
                              uhub0: 8 ports with 8 removable, self powered
                              ugen2.2: <American Power Conversion Back-UPS RS 550G FW857.L4 .I USB FWL4> at usbus2
                              (aprobe0:ata0:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 00 00 00
                              (aprobe0:ata0:0:1:0): CAM status: Command timeout
                              (aprobe0:ata0:0:1:0): Error 5, Retries exhausted
                              ada0 at ata2 bus 0 scbus1 target 1 lun 0
                              ada0: <WDC WD3200AAKS-00G3A0 40.00A40> ATA8-ACS SATA 2.x device
                              cd0 at ata0 bus 0 scbus0 target 0 lun 0
                              ada0: Serial Number WD-WMAUC0015474
                              ada0: 300.000MB/s transferscd0:  (SATA 2.x, UDMA5, PIO 8192bytes<PHILIPS DVD+-RW DVD8701 5D24> Removable CD-ROM SCSI device
                              cd0: Serial Number MY0M9753701595AD01HQ
                              cd0: 33.300MB/s transfers)
                              ada0: 305245MB (625142448 512 byte sectors)
                               (UDMA2, ATAPI 12bytes, PIO 65534bytes)
                              cd0: Attempt to query device size failed: NOT READY, Medium not present
                              Trying to mount root from ufs:/dev/ufsid/54ca20c41b3d50b0 [rw]...
                              random: unblocking device.
                              CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.07-MHz K8-class CPU)
                                Origin="GenuineIntel"  Id=0xf43  Family=0xf  Model=0x4  Stepping=3
                                Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
                                Features2=0x649d<SSE3,DTES64,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
                                AMD Features=0x20100800<SYSCALL,NX,LM>
                                TSC: P-state invariant
                              est0: <Enhanced SpeedStep Frequency Control> on cpu0
                              est: CPU supports Enhanced Speedstep, but is not recognized.
                              est: cpu_vendor GenuineIntel, msr 102d0000102d
                              device_attach: est0 attach returned 6
                              est1: <Enhanced SpeedStep Frequency Control> on cpu1
                              est: CPU supports Enhanced Speedstep, but is not recognized.
                              est: cpu_vendor GenuineIntel, msr 102d0000102d
                              device_attach: est1 attach returned 6
                              lo0: link state changed to UP
                              em3: link state changed to UP
                              fxp0: link state changed to DOWN
                              gif0: link state changed to UP
                              tun1: changing name to 'ovpns1'
                              ovpns1: link state changed to UP
                              pflog0: promiscuous mode enabled
                              gif0: link state changed to DOWN
                              gif0: link state changed to UP
                              DUMMYNET 0 with IPv6 initialized (100409)
                              load_dn_sched dn_sched FIFO loaded
                              load_dn_sched dn_sched QFQ loaded
                              load_dn_sched dn_sched RR loaded
                              load_dn_sched dn_sched WF2Q+ loaded
                              load_dn_sched dn_sched PRIO loaded
                              load_dn_sched dn_sched FQ_CODEL loaded
                              load_dn_sched dn_sched FQ_PIE loaded
                              load_dn_aqm dn_aqm CODEL loaded
                              load_dn_aqm dn_aqm PIE loaded
                              fxp0: link state changed to UP
                              em1: link state changed to UP
                              ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to accept, logging disabled
                              IPFW: starting up interface tracker
                              em3: link state changed to DOWN
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              em3: link state changed to UP
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              gif0: link state changed to DOWN
                              arpresolve: can't allocate llinfo for 192.168.10.1 on em3
                              gif0: link state changed to DOWN
                              gif0: link state changed to UP
                              gif0: link state changed to DOWN
                              gif0: link state changed to UP
                              gif0: link state changed to DOWN
                              gif0: link state changed to UP
                              ovpns1: link state changed to DOWN
                              ovpns1: link state changed to UP
                              arp: 192.168.2.132 moved from f8:a2:d6:4b:dc:bd to fa:a2:c5:4b:64:44 on fxp0
                              

                              The logs shows the hardware inventory of the kernel.
                              Could be interessting, because

                              ** Power Savings Activate Enable PowerD

                              and if the MB doesn't support that FreeBSD approach of implementing PowerD, anything can happen (just an example).

                              What about rebooting when you reached the "Backup -1-Post " : if it comes back fine, you know you can proceed oen step ...

                              No "help me" PM's please. Use the forum, the community will thank you.
                              Edit : and where are the logs ??

                              W 2 Replies Last reply Reply Quote 0
                              • W
                                WhiteTiger-IT @Gertjan
                                last edited by

                                @Gertjan
                                I can't even connect to SSH, which I'm sure I have enabled.
                                I also thought it might be PowerSaving.
                                The Motherboard expects this and the CPU is a Celeron. So this shouldn't be the problem.
                                However I install pfSense again and don't enable the option. I had already "discarded" the standby of the disc.
                                Considering that little is used, I would not mind that they would consume less, if everything does not stop.
                                Now I reset pfSense another time

                                1 Reply Last reply Reply Quote 0
                                • W
                                  WhiteTiger-IT @Gertjan
                                  last edited by

                                  @Gertjan
                                  Is it normal that after installation I cannot surf the Internet from the LAN?
                                  I have to use a second PC connection on a Hotspot of my Smartphone to be able to surf the Internet and access the documentation.

                                  GertjanG 1 Reply Last reply Reply Quote 0
                                  • GertjanG
                                    Gertjan @WhiteTiger-IT
                                    last edited by Gertjan

                                    @WhiteTiger-IT said in First installation, but PC no longer connects:

                                    Is it normal that after installation I cannot surf the Internet from the LAN?

                                    If the LAN NIC is ok, your PC NIC is ok, the cable is ok - and at least one of the NIC's support MDX (rather standard these days, before you needed a hub/switch/or cross over cable), then all you need is a cable and your connected.

                                    Do understand that I use just one line for something that needs to meets hundreds of conditions to work.

                                    Your PC will use it's default DHCP client to obtain an IP (and mask and gateway and DNS) from the DHCP server on pfSense - this is something every router on earth does, pfSense does the same thing.
                                    This can be sen in the DHCP server log right away.
                                    On your PC, a Windows thing ? Enter

                                    ipconfig /all
                                    

                                    and you see the other side.

                                    edit : just by any chance : when you set up the DHCP pool on LAN, it's bigger as "1" - something like 192.168.1.10 to 192.168.1.100 and the LAN's mask is /24, not /32 (yep, this happens).

                                    No "help me" PM's please. Use the forum, the community will thank you.
                                    Edit : and where are the logs ??

                                    W 1 Reply Last reply Reply Quote 0
                                    • W
                                      WhiteTiger-IT @Gertjan
                                      last edited by

                                      @Gertjan said in First installation, but PC no longer connects:
                                      The cable is OK, the switch is a good HP and it's OK.
                                      On the other hand, the problem occurs after switching off and on.
                                      pfSense refuses the connection.
                                      Now I do a new installation of Win10Pro.
                                      Mine is a clean PC with only very few applications installed: Dropbox, OpenVPN, VMWare Workstation, Evernote.
                                      I do a new installation since on the net we talk about the problems with the latest Win Updates, but I'm sure that's not the problem.
                                      Now I'm going by attempts.

                                      GertjanG 1 Reply Last reply Reply Quote 0
                                      • GertjanG
                                        Gertjan @WhiteTiger-IT
                                        last edited by Gertjan

                                        @WhiteTiger-IT said in First installation, but PC no longer connects:

                                        problems with the latest Win Updates

                                        2004 ?
                                        Runs fine on several machines here.

                                        @WhiteTiger-IT said in First installation, but PC no longer connects:

                                        VMWare Workstation

                                        This one can do 'things' with the NIC of your PC .... Never sued it myself, although I have a VM using Windows Pro Hyper-V running pfSense just fine @home.

                                        edit : side note : I wouldn't call a today fresh Windows machine a "clean" thing.
                                        Bought two news PC's from dell this morning, equipped with Win10Pro and probably lose my temper (again) when I see that Candy & family popping up in my phase. These two PC's will get probably de-bloated first.

                                        No "help me" PM's please. Use the forum, the community will thank you.
                                        Edit : and where are the logs ??

                                        W 1 Reply Last reply Reply Quote 0
                                        • W
                                          WhiteTiger-IT @Gertjan
                                          last edited by

                                          @Gertjan
                                          New installation from scratch of pfSense.
                                          New installation from scratch of Win10 Pro.
                                          No configuration neither in pfSense, nor in Win 10; not even an update.
                                          A failed connection error returns from Edge http://192.168.1.1 and https://192.168.1.1.
                                          I also tried with Xubuntu 20.04 Live. Always mistake.

                                          With the PC clean and from a Live there are no more potential conflicts with other particular programs or configurations.
                                          On the other hand, this PC has always connected to IPFire, OpnSense, Proxmox, VMWare ESXi, Debian & Ubuntu Server.
                                          I have never had connection problems, both when SSH was needed and when I had to use a web panel.

                                          Tomorrow I change the firewall PC, but I don't understand why since it never gave problems.

                                          Then I give up because I don't know what to do anymore.

                                          P.S .: I don't think it's some game that MS downloads in the Start Menu to create problems since I haven't even opened it.

                                          GertjanG 1 Reply Last reply Reply Quote 0
                                          • GertjanG
                                            Gertjan @WhiteTiger-IT
                                            last edited by

                                            @WhiteTiger-IT said in First installation, but PC no longer connects:

                                            I change the firewall PC

                                            What firewall ? where ? WinPro10 ?
                                            When you buy a new PC, and you hook it to to some SOHO router - any router - it will obtain IP settings, and "connect to the net". Exception : the upstream network isn't using default settings, your you're behind a captive portal, you're using a company network with an "admin" above you. Or your WinPro10 found an Microsoft AD server, and that one forbid any network activity. But these things are rare and known in advance.

                                            Have a look at these : https://www.youtube.com/results?search_query=pfsense+setup - look at any of them and see for yourself that there is really nothing special.

                                            No "help me" PM's please. Use the forum, the community will thank you.
                                            Edit : and where are the logs ??

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.