Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile

    Scheduled Pinned Locked Moved Problems Installing or Upgrading pfSense Software
    31 Posts 9 Posters 9.8k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by

      @maartenv said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

      media 10Gbase-SR mediaopt full-duplex

      Hmm, it only shows 10Gbase-SR as an available connection and you're trying to use 10Gbase-T.

      If you try a different SFP+ module in the NIC does it show any other available link types? Or any further info from the module?

      It may just not be compatible with 10Gbase-T modules.

      Steve

      M 1 Reply Last reply Reply Quote 0
      • M
        maartenv @stephenw10
        last edited by

        @stephenw10 said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

        @maartenv said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

        media 10Gbase-SR mediaopt full-duplex

        Hmm, it only shows 10Gbase-SR as an available connection and you're trying to use 10Gbase-T.

        If you try a different SFP+ module in the NIC does it show any other available link types? Or any further info from the module?

        It may just not be compatible with 10Gbase-T modules.

        Steve
        Hello Steve,

        Thanks for your help. I was under the impression that DAC cables with 10G sfp+ Modules (for short distances) were compatible with 10Gbase-SR and the this NIC can handle both 1Gb (because the media converter that I bought for testing can only do 1Gb) and 10Gb. (because I thought the only difference is that copper is used instead of fiber). So am I wrong and must the NIC itself also be 10Gbase-T compatible?
        Quite complex (for a newbie) all these different cables and modules for 10G sfp+ NIC's Also it is interesting to see that the DAC cable works fine between two Media Converters (I have two of them) So probably you are right and is the NIC not 10Gbase-T compatible and now I am curious if the Media Converters will be 10Gbase-SR compatible?

        Anyway I will buy 10Gbase-SR modules and see what happens than. I will keep you informed.

        Maarten

        M 1 Reply Last reply Reply Quote 0
        • M
          maartenv @maartenv
          last edited by

          @maartenv said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

          It may just not be compatible with 10Gbase-T modules.

          Thinking about it, most likely is that the media converters are the problem, not the DAC cable because I also received a Cisco SFP H10GB CU cable together with one of the NICS, so I suppose that should work. Tomorrow I will receive a new computer on which I will install Freebsd or Linux and one of the other NIC's and connect the pfSense box directly to this new computer.

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Ah sorry, I thought you meant SFP+ RJ-45 modules but in fact you mean separate media converters?

            I would also expect those to work with DAC cables though maybe not at 1G. That often requires setting the link speed manually and it doesn't appear to be giving you that option.

            I would still try some different modules in there to see if it reports anything different.

            You could also try just linking the two QK NICs with a DAC cable directly just to see if they do then link and what media the driver reports.

            Steve

            M 1 Reply Last reply Reply Quote 0
            • M
              maartenv @stephenw10
              last edited by

              @stephenw10 said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

              You could also try just linking the two QK NICs with a DAC cable directly just to see if they do then link and what media the driver reports.

              Hello Stephen,

              I installed a second pc and connected pfSense with the linux guest pc (Both with an HP Qlogic NC523SFP nic) and now both interfaces are up. (also the port lights of both nics are burning) It seems that the problem was with the media converter.

              Nevertheless I get no connection between pfSense and the guest pc. On pfSense I continuously get the following error

              Jul 29 19:28:47 pfSense kernel: ql0: qla_hw_send: (nsegs[1, 42, 0x0] > Q8_TX_MAX_SEGMENTS)
              Jul 29 19:28:47 pfSense kernel: ql0: qla_dump_buf8: qla_hw_send: wrong pkt 0x2a dump start
              Jul 29 19:28:47 pfSense kernel: ql0: 0x00000000: c4 34 6b cc b1 f0 c4 34 6b cc f9 e0 08 06 00 01
              Jul 29 19:28:47 pfSense kernel: ql0: 0x00000010: 08 00 06 04 00 02 c4 34 6b cc f9 e0 c0 a8 0a 01
              Jul 29 19:28:47 pfSense kernel: ql0: 0x00000020: c4 34 6b cc b1 f0 c0 a8 0a 0b
              Jul 29 19:28:47 pfSense kernel: ql0: qla_dump_buf8: qla_hw_send: wrong pkt dump end

              The above message stops when I assign a static ip address (in the correct ip range! Because the guest pc keeps searching for a dhcp address) but I still don't get a Lan connection. Also Status/DHCP Leases in pfSense stay empty though I Enabled DHCP server on LAN interface

              Both nics are set to 10Gb full duplex (the guest pc manually) And the hardware of both pfSense and the guest PC is 100% identical.

              Shell Output - ifconfig -vvvm ql0
              ql0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
              options=8003b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,LINKSTATE>
              capabilities=8013b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,TSO4,LINKSTATE>
              ether c4:34:6b:cc:f9:e0
              hwaddr c4:34:6b:cc:f9:e0
              inet6 fe80::c634:6bff:fecc:f9e0%ql0 prefixlen 64 scopeid 0x2
              inet 192.168.10.1 netmask 0xffffff00 broadcast 192.168.10.255
              nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
              media: Ethernet 10Gbase-SR <full-duplex>
              status: active
              supported media:
              media autoselect
              media 10Gbase-SR mediaopt full-duplex

              And this is dmesg.boot
              Copyright (c) 1992-2020 The FreeBSD Project.
              Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
              The Regents of the University of California. All rights reserved.
              FreeBSD is a registered trademark of The FreeBSD Foundation.
              FreeBSD 11.3-STABLE #243 abf8cba50ce(RELENG_2_4_5): Tue Jun 2 17:53:37 EDT 2020
              root@buildbot1-nyi.netgate.com:/build/ce-crossbuild-245/obj/amd64/YNx4Qq3j/build/ce-crossbuild-245/sources/FreeBSD-src/sys/pfSense amd64
              FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
              VT(vga): resolution 640x480
              CPU: AMD Ryzen 3 3200G with Radeon Vega Graphics (3593.33-MHz K8-class CPU)
              Origin="AuthenticAMD" Id=0x810f81 Family=0x17 Model=0x18 Stepping=1
              Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
              Features2=0x7ed8320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
              AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
              AMD Features2=0x35c233ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,SKINIT,WDT,TCE,Topology,PCXC,PNXC,DBE,PL2I,MWAITX>
              Structured Extended Features=0x209c01a9<FSGSBASE,BMI1,AVX2,SMEP,BMI2,RDSEED,ADX,SMAP,CLFLUSHOPT,SHA>
              XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
              AMD Extended Feature Extensions ID EBX=0x1007<CLZERO,IRPerf,XSaveErPtr>
              SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=32768
              TSC: P-state invariant, performance statistics
              real memory = 17179869184 (16384 MB)
              avail memory = 14359818240 (13694 MB)
              Event timer "LAPIC" quality 600
              ACPI APIC Table: <ALASKA A M I >
              FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
              FreeBSD/SMP: 1 package(s) x 4 core(s)
              ioapic0 <Version 2.1> irqs 0-23 on motherboard
              ioapic1 <Version 2.1> irqs 24-55 on motherboard
              SMP: AP CPU #2 Launched!
              SMP: AP CPU #1 Launched!
              SMP: AP CPU #3 Launched!
              Timecounter "TSC-low" frequency 1796665086 Hz quality 1000
              random: entropy device external interface
              ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
              ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff806a2f20, 0) error 1
              wlan: mac acl policy registered
              ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
              ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806a2fd0, 0) error 1
              ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
              ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff806a3080, 0) error 1
              iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
              iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff806ca140, 0) error 1
              iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
              iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff806ca1f0, 0) error 1
              iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
              iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
              module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff806ca2a0, 0) error 1
              kbd1 at kbdmux0
              000.000022 [4213] netmap_init netmap: loaded module
              module_register_init: MOD_LOAD (vesa, 0xffffffff812d9960, 0) error 19
              random: registering fast source Intel Secure Key RNG
              random: fast provider: "Intel Secure Key RNG"
              mlx5en: Mellanox Ethernet driver 3.5.2 (September 2019)
              nexus0
              vtvga0: <VT VGA driver> on motherboard
              cryptosoft0: <software crypto> on motherboard
              padlock0: No ACE support.
              acpi0: <ALASKA A M I > on motherboard
              acpi0: Power Button (fixed)
              cpu0: <ACPI CPU> on acpi0
              cpu1: <ACPI CPU> on acpi0
              cpu2: <ACPI CPU> on acpi0
              cpu3: <ACPI CPU> on acpi0
              attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
              Timecounter "i8254" frequency 1193182 Hz quality 0
              Event timer "i8254" frequency 1193182 Hz quality 100
              atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
              atrtc0: registered as a time-of-day clock, resolution 1.000000s
              Event timer "RTC" frequency 32768 Hz quality 0
              hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0
              Timecounter "HPET" frequency 14318180 Hz quality 950
              Event timer "HPET" frequency 14318180 Hz quality 450
              Event timer "HPET1" frequency 14318180 Hz quality 450
              Event timer "HPET2" frequency 14318180 Hz quality 450
              Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
              acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
              pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
              pcib0: _OSC returned error 0x10
              pci0: <ACPI PCI bus> on pcib0
              pci0: <base peripheral, IOMMU> at device 0.2 (no driver attached)
              pcib1: <ACPI PCI-PCI bridge> at device 1.2 on pci0
              pci1: <ACPI PCI bus> on pcib1
              xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfc9a0000-0xfc9a7fff irq 28 at device 0.0 on pci1
              xhci0: 32 bytes context size, 64-bit DMA
              xhci0: Unable to map MSI-X table
              usbus0 on xhci0
              usbus0: 5.0Gbps Super Speed USB v3.0
              ahci0: <AHCI SATA controller> mem 0xfc980000-0xfc99ffff irq 29 at device 0.1 on pci1
              ahci0: AHCI v1.31 with 8 6Gbps ports, Port Multiplier supported
              ahcich0: <AHCI channel> at channel 0 on ahci0
              ahcich1: <AHCI channel> at channel 1 on ahci0
              ahcich4: <AHCI channel> at channel 4 on ahci0
              ahcich5: <AHCI channel> at channel 5 on ahci0
              pcib2: <ACPI PCI-PCI bridge> irq 30 at device 0.2 on pci1
              pci2: <ACPI PCI bus> on pcib2
              pcib3: <ACPI PCI-PCI bridge> irq 28 at device 0.0 on pci2
              pci3: <ACPI PCI bus> on pcib3
              pcib4: <ACPI PCI-PCI bridge> irq 29 at device 1.0 on pci2
              pci4: <ACPI PCI bus> on pcib4
              re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xf000-0xf0ff mem 0xfc800000-0xfc800fff,0xf0300000-0xf0303fff irq 29 at device 0.0 on pci4
              re0: Using 1 MSI-X message
              re0: Chip rev. 0x4c000000
              re0: MAC rev. 0x00000000
              miibus0: <MII bus> on re0
              rgephy0: <RTL8251 1000BASE-T media interface> PHY 1 on miibus0
              rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
              re0: Using defaults for TSO: 65518/35/2048
              re0: Ethernet address: a8:a1:59:27:d2:04
              re0: netmap queues/slots: TX 1/256, RX 1/256
              pcib5: <ACPI PCI-PCI bridge> irq 28 at device 4.0 on pci2
              pci5: <ACPI PCI bus> on pcib5
              ql0: <Qlogic ISP 80xx PCI CNA Adapter-Ethernet Function v1.1.36> mem 0xfc400000-0xfc5fffff,0xfc690000-0xfc69ffff irq 28 at device 0.0 on pci5
              ql0: qla_pci_attach: firmware[4.20.1.1429931003]
              ql0: Ethernet address: c4:34:6b:cc:f9:e0
              ql1: <Qlogic ISP 80xx PCI CNA Adapter-Ethernet Function v1.1.36> mem 0xfc200000-0xfc3fffff,0xfc680000-0xfc68ffff irq 28 at device 0.1 on pci5
              ql1: qla_pci_attach: firmware[4.20.1.1429931003]
              ql1: Ethernet address: c4:34:6b:cc:f9:e4
              pcib6: <ACPI PCI-PCI bridge> at device 8.1 on pci0
              pci6: <ACPI PCI bus> on pcib6
              vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xe0000000-0xefffffff,0xf0000000-0xf01fffff,0xfcd00000-0xfcd7ffff irq 52 at device 0.0 on pci6
              vgapci0: Boot video device
              hdac0: <ATI (0x15de) HDA Controller> mem 0xfcd88000-0xfcd8bfff irq 53 at device 0.1 on pci6
              pci6: <encrypt/decrypt> at device 0.2 (no driver attached)
              xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfcb00000-0xfcbfffff irq 55 at device 0.3 on pci6
              xhci1: 64 bytes context size, 64-bit DMA
              xhci1: Unable to map MSI-X table
              usbus1 on xhci1
              usbus1: 5.0Gbps Super Speed USB v3.0
              xhci2: <XHCI (generic) USB 3.0 controller> mem 0xfca00000-0xfcafffff irq 52 at device 0.4 on pci6
              xhci2: 64 bytes context size, 64-bit DMA
              xhci2: Unable to map MSI-X table
              usbus2 on xhci2
              usbus2: 5.0Gbps Super Speed USB v3.0
              hdac1: <AMD (0x15e3) HDA Controller> mem 0xfcd80000-0xfcd87fff irq 54 at device 0.6 on pci6
              pcib7: <ACPI PCI-PCI bridge> at device 8.2 on pci0
              pci7: <ACPI PCI bus> on pcib7
              ahci1: <AMD KERNCZ AHCI SATA controller> mem 0xfce00000-0xfce007ff irq 54 at device 0.0 on pci7
              ahci1: AHCI v1.31 with 1 6Gbps ports, Port Multiplier supported with FBS
              ahcich8: <AHCI channel> at channel 0 on ahci1
              isab0: <PCI-ISA bridge> at device 20.3 on pci0
              isa0: <ISA bus> on isab0
              acpi_button0: <Power Button> on acpi0
              uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
              atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
              atkbd0: <AT Keyboard> irq 1 on atkbdc0
              kbd0 at atkbd0
              atkbd0: [GIANT-LOCKED]
              ppc0: cannot reserve I/O port range
              hwpstate0: <Cool`n'Quiet 2.0> on cpu0
              ZFS filesystem version: 5
              ZFS storage pool version: features support (5000)
              Timecounters tick every 1.000 msec
              hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
              hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
              pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
              pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
              pcm2: <ATI R6xx (HDMI)> at nid 7 on hdaa0
              hdacc1: <Realtek ALC892 HDA CODEC> at cad 0 on hdac1
              hdaa1: <Realtek ALC892 Audio Function Group> at nid 1 on hdacc1
              pcm3: <Realtek ALC892 (Rear Analog)> at nid 20 and 24,26 on hdaa1
              pcm4: <Realtek ALC892 (Front Analog)> at nid 27 and 25 on hdaa1
              ugen1.1: <0x1022 XHCI root HUB> at usbus1
              ugen0.1: <0x1022 XHCI root HUB> at usbus0
              ugen2.1: <0x1022 XHCI root HUB> at usbus2
              uhub0: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
              uhub2: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
              uhub1: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus2
              uhub1: 2 ports with 2 removable, self powered
              uhub0: 8 ports with 8 removable, self powered
              uhub2: 22 ports with 22 removable, self powered
              ugen0.2: <USB USB Keyboard> at usbus0
              ukbd0 on uhub2
              ukbd0: <USB USB Keyboard, class 0/0, rev 1.10/1.10, addr 1> on usbus0
              kbd2 at ukbd0
              uhid0 on uhub2
              uhid0: <USB USB Keyboard, class 0/0, rev 1.10/1.10, addr 1> on usbus0
              ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
              ada0: <ST250DM000-1BD141 KC48> ATA8-ACS SATA 3.x device
              ada0: Serial Number Z6EK74HT
              ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
              ada0: Command Queueing enabled
              ada0: 238475MB (488397168 512 byte sectors)
              ada0: quirks=0x1<4K>
              ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
              ada1: <ST250DM000-1BD141 KC48> ATA8-ACS SATA 3.x device
              ada1: Serial Number Z6EK54KD
              ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
              ada1: Command Queueing enabled
              ada1: 238475MB (488397168 512 byte sectors)
              ada1: quirks=0x1<4K>
              random: unblocking device.
              Trying to mount root from zfs:FW02/ROOT/default []...
              CPU: AMD Ryzen 3 3200G with Radeon Vega Graphics (3593.33-MHz K8-class CPU)
              Origin="AuthenticAMD" Id=0x810f81 Family=0x17 Model=0x18 Stepping=1
              Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
              Features2=0x7ed8320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
              AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
              AMD Features2=0x35c233ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,SKINIT,WDT,TCE,Topology,PCXC,PNXC,DBE,PL2I,MWAITX>
              Structured Extended Features=0x209c01a9<FSGSBASE,BMI1,AVX2,SMEP,BMI2,RDSEED,ADX,SMAP,CLFLUSHOPT,SHA>
              XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
              AMD Extended Feature Extensions ID EBX=0x1007<CLZERO,IRPerf,XSaveErPtr>
              SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=32768
              TSC: P-state invariant, performance statistics

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by stephenw10

                Some hardware off loading error maybe? Make sure that are all disabled in Sys > Adv > Networking.

                Otherwise that's probably a question for the FreeBSD forum. There are likely many more people running those NICs there.

                This looks relevant: https://www.reddit.com/r/freenas/comments/957hz0/hp_nc523sfp_10gb/

                Steve

                M 1 Reply Last reply Reply Quote 0
                • M
                  maartenv @stephenw10
                  last edited by

                  @stephenw10

                  Hello Stephen

                  It seems to be a bug: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=226217
                  also they show how that bug can be fixed and as I am not a programmer I don't how to do that.

                  But luckily there is also a simple workaround for it: First take out the cable(s) and do: ifconfig ql0 & ql1 mtu 1500 and that works fine, I get a connection! 😊

                  Now I am putting these commands in /boot/loader.conf.local and will check if this also works. I will let you know

                  M 1 Reply Last reply Reply Quote 0
                  • M
                    maartenv @maartenv
                    last edited by

                    @maartenv said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

                    Now I am putting these commands in /boot/loader.conf.local and will check if this also works. I will let you know

                    Unfortunately loading these commands don't work with /boot/loader.conf.local

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by stephenw10

                      Yeah, those are not boot loader commands.

                      You might be able to run them as early shellcmds either directly or call a shell script:
                      https://docs.netgate.com/pfsense/en/latest/development/executing-commands-at-boot-time.html

                      They have to be run with the cable actually disconnected? Not just DOWN the interface?

                      M 1 Reply Last reply Reply Quote 0
                      • M
                        maartenv @stephenw10
                        last edited by

                        @stephenw10 said in HP Qlogic NC523SFP Driver install Freebsd 11 pfsense kernal recompile:

                        Yeah, those are not boot loader commands.

                        You might be able to run them as early shellcmds either directly or call a shell script:
                        https://docs.netgate.com/pfsense/en/latest/development/executing-commands-at-boot-time.html

                        They have to be run with the cable actually disconnected? Not just DOWN the interface?

                        You are probably right, but I did not yet try that. Also I will try to find the source file with the bugs on FreeBSD, change the lines with the bugs, compile the file and than copy the new file to pfSense.
                        I will keep you informed about both solutions

                        Maarten

                        1 Reply Last reply Reply Quote 1
                        • bingo600B bingo600 referenced this topic on
                        • bingo600B bingo600 referenced this topic on
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.