VLANs blocked by Firewall

kiokoman

@r801248
use opt3, i don't know if youcan do that with packet capture from pfsense, i use wireshark
did you try to reboot pfsense and the switch?

r801248

@kiokoman

Both rebooted.

cburbs

@r801248 What is your Port PVID Config look like? ooops that was posted earlier.

What does this look like?

That config looks correct even looking at this ...

https://kb.netgear.com/11673/How-do-I-setup-a-VLAN-trunk-link-between-two-NETGEAR-switches

Also on the switch Select Switching > VLAN > Advanced > VLAN Status. what does that look like?

r801248

@cburbs Hello,

This is what they look like...

vlans status.png

cburbs

@r801248

And if you plug your laptop into ports 3-7 you mentioned you do get a dhcp from VLAN10 (10.70.10.0/24) ? Can you also get out to the internet on those ports?

Have you tried to add say Port 5 to vlan10 untagged and plug into that to see what happens?

Maybe delete that Vlan 10 from the switch and start over with it?

r801248

@cburbs
When I plug the laptop into g3-g7 I get a DHCP from the parent interface (10.70.0.0/24) - Yes, I get out to the internet.
Adding any other port (untagged) makes it behave like g1-g2.

kiokoman

@r801248
did you check if there is a firmware update for that netgear?

r801248

@kiokoman
There is an upgrade. I guess I'll go that route.
Thanks,

r801248

@r801248
Upgraded. Same results. Frustrating.

cburbs

@r801248

And the switch has a static IP not in any of the DHCP ranges?

You may want to set the switch back to default and start over with it again.

r801248

@cburbs Yes, the static address is outside the range. Resetting to default values did not change the results.

Gertjan

Normally, with these :

Traffic can enter OPT3.

Before the final, hidden "drop all" (non-vsible) there is a another hidden rule that let DHCP traffic (UDP, port 67 and ...) come in.
So, what ever happens, DHCP should work. But you can see it work.
Place an pass rule at the top with proto is UDP and port = 67.
Do not use "OPT3 net" as a source, as DHCP traffic is mostly broadcast = 0.0.0.0

What you should see now is that these :

should start to count.

If not : check the NIC, cable, switch and the most obvious one : VLAN settings.

Btw : when issues, go check the real firewall.
It's here, a file : /tmp/rules.debug

marvosa

Some of this stuff has already been mentioned, but the rules on OPT3 have zero hits. So there are multiple areas to look at.

My suggestion:

Put an any/any rule at the top of OPT3 and disable everything else until basic IP communication is established.
Remove VLAN1 from g8 on the switch
Remove the 10.70.0.0/24 subnet from OPT2 and leave it undefined
Bounce the DHCP server on OPT3
Reboot the PC connected to g1 or g2

After the above, provided the switch is configured properly... everything should be passed and working as expected.

A cleanup item once you get everything working... remove that OPT3 net/OPT3 net rule... it's doing absolutely nothing.

r801248

@marvosa
Hi,
The switch loses connectivity when VLAN1 is removed from g8, tried it before.
Also, upon rebooting the router, there is a brief connection through VLAN10. Only lasts a couple of seconds though. Logs below -

DHCP Leases
vlan10 status.png
DHCP Log
dhcp log.png

Then it drops,

Firewall log
firewall log.png

marvosa

Also, upon rebooting the router, there is a brief connection through VLAN10. Only lasts a couple of seconds though. Logs below -

Sounds like traffic may be passing until the rules get loaded. Did you add the any/any rule?

r801248

@marvosa
I did. That's the only rule in OPT3

cburbs

@r801248

This setup is on igb3 correct?

Have you tried to get a vlan going correctly on igb0 instead - maybe something flaky going on with igb3.

I just came across this so maybe look into this - https://community.netgear.com/t5/Managed-Switches/GS110TP-won-t-retain-VLAN-membership-on-port-8/td-p/1446089

See if that is set for port mirroring.

Or I guess just try port 7 as your trunk/tagged port and see what happens as well.

marvosa

I agree. The usual suspects are typically... something's not configured properly, not plugged in properly, or not function properly.

Not seeing anything glaring in the configs, so I'd start trying things like...different ports on the switch, different cables, try moving the VLANs to a different NIC, try a different switch, etc.

I've also read a few posts where after trying everything... people have reset PFsense to factory default, re-built their config from scratch and everything somehow magically starts working.

r801248

@marvosa

I guess I'll go that route and reset and reconfigure the box.

Thanks,

cburbs

@r801248 said in VLANs blocked by Firewall:

@marvosa

I guess I'll go that route and reset and reconfigure the box.

Thanks,

Look at the last thing I posted to see if you see anything odd with port 8 -

Try port 7 before you do a reconfigure as your trunk port just to see.

Then maybe reconfigure.