Playing with fq_codel in 2.4
-
@pentangle said in Playing with fq_codel in 2.4:
@dtaht @strangegopher There's also this https://www.bufferbloat.net/projects/make-wifi-fast/wiki/
That website (I'm the co-author) is a bit out of date. We didn't get funding last year... or this year. Still, the google doc at the bottom of that page is worth reading.... lots more can be done to make wifi better.
-
@dtaht said in Playing with fq_codel in 2.4:
My biggest open question however is that we are hitting cpu limits on various higher speeds, and usually the way to improve that is to increase the token bucket size. Is there a way to do that here?
Yes, it appears we can.
https://www.freebsd.org/cgi/man.cgi?query=ipfw
burst size If the data to be sent exceeds the pipe's bandwidth limit (and the pipe was previously idle), up to size bytes of data are allowed to bypass the dummynet scheduler, and will be sent as fast as the physical link allows. Any additional data will be transmitted at the rate specified by the pipe bandwidth. The burst size depends on how long the pipe has been idle; the effec- tive burst size is calculated as follows: MAX( size , bw * pipe_idle_time). -
um, er, no, I think. That's the queue size. We don't need to muck with that.
A linux "limiter" has a token bucket size and burst and cburst and quantum parameters to control how much data gets dumped into the next pipe in line per virtual interrupt.
A reasonable explanation here
https://unix.stackexchange.com/questions/100785/bucket-size-in-tbf
Or http://linux-ip.net/articles/Traffic-Control-HOWTO/classful-qdiscs.html
I'm so totally not familar with what's in bsd, but... what I wanted to set was the bucket size... the burst value, the cburst value. You are setting the token rate only, so far as I can tell. At higher rates, you need bigger buckets.
from some bsd stuff elsehwere
A token bucket has
token rate'' andbucket size''.
Tokens accumulate in a bucket at the averagetoken rate'', up to thebucket size''.
A driver can dequeue a packet as long as there are positive
tokens, and after a packet is dequeued, the size of the packet is
subtracted from the tokens.
Note that this implementation allows the token to be negative as a
deficit in order to make a decision without prior knowledge of the
packet size.
It differs from a typical token bucket that compares the packet
size with the remaining tokens beforehand.The bucket size controls the amount of burst that can dequeued at a time, and controls a greedy device trying dequeue packets as much as possible. This is the primary purpose of the token bucket regulator, and thus, the token rate should be set to the actual maximum transmission rate of the interface. -
@dtaht thanks for the correction - I've edited my previous submission. It appears we can edit burst in ipfw/dummynet so I can play with that.
-
@uptownvagrant That's closer, but we do want to dump it into the next pipe inline. Reading that seems to indicate it bypasses everything? A quantum? A bucket size?
Worth trying anyway...
-
Not to derail this thread any more off of the FQ_CODEL topic, but I thought I should mention this insane setup is actually working on my end; I think you especially will find this amusing:
| pfSense vRouter | | "edge" vRouter | | | | linux 4.9 | | | | br0: | | (no shaping) | --WAN0--> |eth1...(cake)...eth2|(vNIC)|i350|--(LAGG)-> Cable Modem | | | br1: | | | --WAN1--> |eth3...(cake)...eth4|(vNIC)|i350|---------> DSL ModemDriving home, I was laughing, thinking this was a dumb idea but, uh, it's kind of keeping up OK. For when you want the best of both worlds (pfSense's firewalling and out-of-tree Cake cloned off Git). So far I'm noticing great stability and of course, next to no bufferbloat.
These are both in the same virtual host, so they just pass traffic between eachother over virtual "Internal" interfaces, and the Linux-based vRouter has been stripped down to the bare minimums, and under load is reporting next to no CPU usage at all, on a 147M connection. I'll have to get some flent results while I'm at this. I might actually stick with it honestly.
-
-
Hi @gsakes and @mattund: The setups you have described sound intriguing and it might be something I want to try as well down the road when I have some spare time and access to an additional machine:
Could you guys talk a little more about how this is setup? Does the Linux machine in front take in all the WAN traffic, shape it and pass it through to pfSense? Are there then two sets of firewalls traffic must traverse (one on pfSense and on the Linux box) or just one? I'm just trying to understand the architecture a bit better and how one would setup up something like what you have described.
Thanks in advance.
-
@tman222 In my case, I'd prefer to use PFSense for firewalling and shaping, but my testing showed that Linux/Cake performs better than PfSense/fq_codel, albeit not by much, maybe 10-15% depending on the load.
As far as the architecture is concerned you don't need to run a firewall on the linux host, you can simply configure it as a router; you'd need two network interfaces, where you'd configure cake using the 'layer.cake' script from the cake github repo on the egress interface.
Taking from @mattund 's example, this is how my setup looks like:
| pfSense FW | Router | | | (no shaping) | Ubuntu Server | | | (192.168.0.0/24)| | (10.18.9.0/24) | | LAN --> | | eth1 --> (cake) --> eth2 | --> Cable Modem | --> WAN | | | | -
@tman222 said in Playing with fq_codel in 2.4:
Does the Linux machine in front take in all the WAN traffic, shape it and pass it through to pfSense?
That is correct, this is an entirely different VM that I have set up bridging on; I'm using Debian since it's what I'm most familiar with. I was able to do it all in
/etc/network/interfaces, after installing Cake following https://www.bufferbloat.net/projects/codel/wiki/Cake/#installing-cake-out-of-tree-on-linux (you may need some packages to install Cake, not to worry, if your build system is missing them just install them):# The loopback network interface auto lo iface lo inet loopback # MANAGEMENT allow-hotplug eth0 iface eth0 inet dhcp # WAN1 iface eth1 inet manual iface eth2 inet manual auto br0 iface br0 inet manual bridge_stp off bridge_waitport 0 bridge_fd 0 bridge_ports eth1 eth2 up tc qdisc add dev eth1 root cake bandwidth 12280kbit ; tc qdisc add dev eth2 root cake bandwidth 122800kbit down tc qdisc del dev eth1 root ; tc qdisc del dev eth2 root # WAN2 iface eth3 inet manual iface eth4 inet manual auto br1 iface br1 inet manual bridge_stp off bridge_waitport 0 bridge_fd 0 bridge_ports eth3 eth4 up tc qdisc add dev eth3 root cake bandwidth 2000kbit ; tc qdisc add dev eth4 root cake bandwidth 27000kbit down tc qdisc del dev eth3 root ; tc qdisc del dev eth4 rootYou just add 5 NICS to a VM:
1: Management
2/3: Internal WAN1, External WAN1 attached to hardware
3/4: Internal WANN+1, External WANN+1 attached to hardwareFYI, I was not aware of netdata before I was informed here, but it is absolutely fantastic if you want to audit your setup.
-
@mattund Yes, netdata is fantastic - I prefer telegraf/grafana or Prometheus for monitoring, but out-of-the box netdata is one of the best apps I've seen in a long time.
-
So in terms of configuration:
Let's say I had my pfSense FW --> Debian Linux Box --> WAN Connection.
Let's say the Debian Box I have had three network interfaces:
if0 Connected to pfSense WAN Interface
if1 DHCP From Management VLAN
if2: WAN Connection (DCHP From ISP)Would I setup if0 with a static IP, e.g. let's say 10.5.5.1 and then connect if0 to my pfSense WAN interface (let's call it pf0)? On the pfSense side I would assign my WAN interface (pf0) another static IP, e.g. 10.5.5.2 and then set 10.5.5.1 as the Gateway? If that's correct so far, what would I have to setup on the linux box to make sure traffic can get out into the internet? I would have to enable ip forwarding and then ensure that if2 becomes the gateway for if0? Also, do I have to setup any firewall rules on the Linux box to make sure that, even though it's just a router, it's not open to the whole internet?
Apologies for these basic questions, I'm having just a bit of trouble visualizing how this would all work in concert.
Thanks again.
-
I opted to only address my management interface; I have not addressed either the if0 or if2 in your scenario, instead I have created a basic bridge over each interface (note my creation of
br0andbr1and lack of addressing above Layer 2 in the interface configuration). Now, in my case I feel fine managing the VM over a management port, so this is fine.Effectively, I've just made a "dumb" Layer2 switch between pfSense and the modems with isolated port pairs, that happens to also use CAKE on each participating interface's outbound, root queue.
Reason being, I wanted an extremely simple setup with as little overhead as possible and as few layers in the stacks of the participating bridge interfaces.
-
if0 -> 10.5.5.1 -> PFSense WAN interface
if2 -> WAN Connection (DCHP From ISP) -> Cable Modempf0 -> 10.5.5.2
On PfSense you would configure the WAN INterface with a static IP in the 10.5.5.0 subnet, and set the gateway to the adress of if0.
It's probably easiest is you use a firewall to set up forwarding etc., and also have one interface. Firehol is great, here is a basic configuration which would work for your setup - just an example, you'd have to adjust for your needs. Please note that this does not firewall anything:)
/etc/firehol/firehol.conf:
version 6 # LAN subnets. lan_ips="10.5.5.0/24 WHATEVER_SUBNET_FOR_YOUR_PFSENSE_LAN/24" interface4 if0 lan src "${lan_ips}" server all accept client all accept policy accept interface4 if1 wan src not "${lan_ips} ${UNROUTABLE_IPS}" protection strong 100/sec 10 server all accept client all accept router4 lan2wan inface if0 outface if1 server all accept client all accept route all accept masqueradeAlso, you'd need to add a route back to your PFSense WAN interface static ip ( you can also do this from firehol, but I prefer the network manager):
/etc/network/if-up.d/custom-routes:
#!/bin/sh route add -net 192.168.0.0/24 gw 10.5.5.2 dev if0Hope this helps to clarify things.
-
@gsakes said in Playing with fq_codel in 2.4:
@tman222 In my case, I'd prefer to use PFSense for firewalling and shaping, but my testing showed that Linux/Cake performs better than PfSense/fq_codel, albeit not by much, maybe 10-15% depending on the load.
As far as the architecture is concerned you don't need to run a firewall on the linux host, you can simply configure it as a router; you'd need two network interfaces, where you'd configure cake using the 'layer.cake' script from the cake github repo on the egress interface.
Taking from @mattund 's example, this is how my setup looks like:
| pfSense FW | Router | | | (no shaping) | Ubuntu Server | | | (192.168.0.0/24)| | (10.18.9.0/24) | | LAN --> | | eth1 --> (cake) --> eth2 | --> Cable Modem | --> WAN | | | |While this is a cool idea, you lose a cake feature by not doing nat on it: per host fq. None of our testing here to date has established the coolness of this feature, you need two or more source ip addresses to test from to see it work.
(yep, flent can do this test too. Not gonna describe how here).
Anyway, if you go this route, use "flows" instead of triple-isolate on cake, and nonat, save some cpu. But I thought we were dealing with a nat bug in pfsense in the first place?
-
@gsakes You can even get rid of any need to have the cake box have ips. Just create a bump in the wire:
https://apenwarr.ca/log/?m=201808
-
Thanks @dtaht - I have seen that link you shared before. Now I'm curious how that "bump" should be spec'd hardware wise to shape at gigabit speeds. Does anyone have any thoughts on that? Also, does OpenWRT run on a normal linux box? if not, is it possible to duplicate the functionality on just a regular Linux install?
-
@dtaht Thanks for the tips Dave, as always much appreciated:) I'm decommissioning my PFSense box for now. I've been using PFSense since 2010, and I don't think there's anything better, but I'll put it on ice until fq_codel matures and/or Cake is implemented. I'm slowly building out this Ubuntu box to be my firewall, using Firehol/Fireqos, netdata and PiHole.
So yes - I will be doing NAT on the box:)
-
@dtaht said in Playing with fq_codel in 2.4:
triple-isolate
Yep, it's the 'per-host-fq' that is a real big factor, compared to fq_codel - frankly the biggest reason for me switching over:)
BTW - Anyone wanting to learn about fq_codel, Cake and the design of both should read this:
Piece of CAKE: A Comprehensive Queue
Management Solution for Home Gateways -
So I read this paper Dummynet AQM v0.1 – CoDel and FQ-CoDel for FreeBSD’s ipfw/dummynet framework
The paper is written by the folks that implemented Codel and FQ-CoDel into FreeBSD ipfw/dummynet. I know @dtaht knows this because he reviewed the source and there is correspondence between them and he back in the day. I'm just catching up - thanks for your patience.
Looking at the examples in the paper, I'm wondering why the Codel AQM is selected in the pfSense WebUI in the August 2018 hangout? Per the FQ-CoDel examples in the paper above, it does not seem appropriate and removing Codel as the AQM from the pipe and queue removes the "flowset busy" error @mattund mentioned 4 months ago. @dtaht this is why I was stating codel+fq-codel - when I first learned about FQ-CoDel being added to pfSense 2.4.4, it was in the hangout video which it instructs to choose Codel as the AQM.
Concerning buckets and CPU utlization, I played with net.inet.ip.dummynet.hash_size which is the closest thing I could find to what you were explaining - pfSense defaults to 256 and I doubled the value on each flent rrul test up to 16384. I had to use sysctl -w net.inet.ip.dummynet.hash_size=$value on the fly in the console because /etc/inc/shaper.inc overwrites the setting to 256 any time you make a change to the limiters. I did not find setting this above 256 to provide real value.
So, unfortunately I haven't made much progress...
