Watchguard Firebox M400/M500
-
@zanthos thx a lot bro, the procedure to flash or suggestions?
-
@devid79
Check this forum post I made(Use a CH341a programmer, a suitable software, i.e. ASProgrammer and you're ready to go.. If you need help, google for "SPI flashing" and watch a lot on youtube
) -
@zanthos order it on amazon
tomorrow comes and I flash with your bios -
@zanthos Excuse bro what the which chip should I select? thx in advantage
-
@devid79
If you use AsProgrammer and while you have it connected to your programmer, click "Read ID" (the button with the green question mark). It sould suggest you the right chip.
Otherwise check your mainboard for the chip. It is located near the SPI pins. Search with google according to the print of the chip. You will find it! -
@zanthos then it will be the pins, i verify thx
-
@zanthos Current programmer: CH341 the firewall is without powercord, i verify the pin but not function
ID(9F): FFFFFF(Unknown)
ID(90): FFFF(Unknown)
ID(AB): FF(Unknown)
ID(15): FFFF(Unknown)sigh sigh
-
Hi, I have a problem that I can't solve. I flashed the latest unlocked bios version and so far so good. The system works, but when I reboot the system does not start and tells me to insert a boot disk. In reality if I enter the bios and modify the boot with the primary disk and save the system it starts, but if I reboot the problem still happens. I noticed that it saves all settings except the boot order. Did it happen to anyone? Can it be the battery of the bios? Other ideas? Thanks everyone for the help
-
It could be the battery yes. What are you trying to boot from? Is that not enabled by default anyway?
Do you have anything else connected that it might be trying to boot from incorrectly?
Steve
-
@stephenw10 Thanks Steve, I installed pfsense on an ssd connected to the sata port. I don't have any other peripherals like usb or connected disks.
For the battery I have to try to replace it, the strange thing is that it does not save me the settings related to the boot, the rest is.
For example I have changed fan speed and it works. With the original bios never had problems.
Did you have problems?
Gabriele -
Nope, never saw an issue like that. The only quirk I've seen was the 4160 CPU will not reboot. Still running from CF though.
Do you have auto detect set or something that might be reconfiguring the drives at each boot maybe?
What does it try to boot from and fail?
Steve
-
@stephenw10 My configuration is:
- original cpu
- 16 GB ram
- boot from ssd
I don't have any extra peripherals.
Tomorrow I will try to replace the battery so I see if it fixes it.
Updates follow
Gabriele
-
Which BIOS did you use?
-
@stephenw10 I use the latest version modified from zanthos v 6.7
-
I noticed, however, that sometimes when I enter the bios it does not always allow me to change the boot order of the disk. it is strange that he gives me the same disk with uefi and not uefi boot which then, even if it does not keep in memory
-
An update, I replaced the bios battery and now everything works. It was probably almost empty and occasionally caused problems.
-
Datapoint:
Tried CT2K204864BD160B (2x16gb) UDIMM unbuffered and it did not work (constant beeps with 1 or 2 sticks) Not sure if ECC or 1.5v is a requirement or that 8gb/stick may be the max despite the lanner manual stating 32gb. I am using the stock Watchguard BIOS so I may try Zanthos's to see if I get different results.
-
Has anyone thought to do a YT video of how to get PFSense into an M400/M500 firebox yet so that others can benefit as the price of these units start to come down?
Thanks,
-
I haven't seen one. It's pretty easy though. Install to CF in something else and swap it in. Or write the installer to CF and install to SSD if you've installed one.
Steve
-
@stephenw10 And what about flashing the bios that I have seen in this thread?
Thanks,
