Average writes to Disk
-
I don't think so - not easy... But I think there is something missing here on what is actually being written.
So from my understanding zpool iostat shows total since boot..
[21.05.1-RELEASE][admin@sg4860.local.lan]/: zpool iostat capacity operations bandwidth pool alloc free read write read write ---------- ----- ----- ----- ----- ----- ----- zroot 969M 25.1G 0 10 645 227K [21.05.1-RELEASE][admin@sg4860.local.lan]/:My box has been up for days.. Since I updated it to 21.05.1
Uptime 6 Days 02 Hours 12 Minutes 47 Seconds
edit: Well that can not be since boot... Not exactly sure what that reads to be honest.. But if you have it report every 2 seconds.
[21.05.1-RELEASE][admin@sg4860.local.lan]/: zpool iostat zroot 2 capacity operations bandwidth pool alloc free read write read write ---------- ----- ----- ----- ----- ----- ----- zroot 970M 25.1G 0 10 645 227K zroot 970M 25.1G 0 0 0 0 zroot 968M 25.1G 0 34 0 552K zroot 968M 25.1G 0 0 0 0 zroot 967M 25.1G 0 35 0 624K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 38 0 532K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 33 0 602K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 34 0 520K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 33 0 618K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 33 0 531K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 33 0 621K zroot 967M 25.1G 0 0 0 0 zroot 967M 25.1G 0 7 0 114K zroot 967M 25.1G 0 24 0 415K zroot 967M 25.1G 0 0 0 0 -
@johnpoz Here is my output - I'm also no ZFS expert!
As far as I see not much different ...
zpool iostat
capacity operations bandwidth
pool alloc free read write read write
zroot 808M 11.7G 0 12 319 214K
zpool iostat zroot 2
capacity operations bandwidth
pool alloc free read write read write
zroot 807M 11.7G 0 12 319 214K
zroot 808M 11.7G 0 35 0 623K
zroot 808M 11.7G 0 30 0 432K
zroot 808M 11.7G 0 1 0 8.00K
zroot 808M 11.7G 0 0 0 0
zroot 807M 11.7G 0 36 0 535K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 32 0 442K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 2 0 28.0K
zroot 807M 11.7G 0 35 0 618K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 32 0 420K
zroot 807M 11.7G 0 3 0 22.0K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 35 0 486K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 32 0 442K
zroot 807M 11.7G 0 0 0 7.99K
zroot 807M 11.7G 0 0 0 5.98K
zroot 807M 11.7G 0 32 0 442K
zroot 807M 11.7G 0 0 0 0
zroot 806M 11.7G 0 1 0 14.0K
zroot 806M 11.7G 0 2 0 28.0K
zroot 806M 11.7G 0 1 0 14.0K
zroot 807M 11.7G 0 33 0 442K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 31 0 428K
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 0 0 0
zroot 807M 11.7G 0 10 0 623K
zroot 808M 11.7G 0 33 0 547K
zroot 808M 11.7G 0 35 0 498K
zroot 808M 11.7G 0 1 0 14.0K -
SG-3100 - 21.05.1 - pfblockerng dnsbl python mode enabled
iostat -d 5 6
-
@mcury I guess FS is UFS and not ZFS ...
-
@fireodo said in Average writes to Disk:
@mcury I guess FS is UFS and not ZFS ...
Indeed, UFS here, noatime in fstab
-
@mcury said in Average writes to Disk:
@fireodo said in Average writes to Disk:
@mcury I guess FS is UFS and not ZFS ...
Indeed, UFS here, noatime in fstab
So it seams to cristallise that ZFS is the problem ...
-
@mcury said in Average writes to Disk:
SG-3100 - 21.05.1 - pfblockerng dnsbl python mode enabled
iostat -d 5 6
This is really interesting because your box does not suffer from sustained writing from UNBOUND (caused by pfBlockerNG in python mode).
That would suggest it’s a setting or configuration detail that causes the issue.I wonder what that might be. I think my setup is fairly default, but I have pfBlockerNG creating alias lists instead of it’s own rules.
Maybe we should start a thread with pfBlockerNG configs to see if we can find the root configuration cause for sustained writing to disk in pfBlockerNG?
-
@keyser Just as a follow up I think I have now tried EVERY possible setting in my pfBlockerNG setup in terms of making it “quiet” on disk writes.
Nothing sticks - No lists, no logging enabled anywhere, nothing - and still I have a UNBOUND process that writes on average about 380 Kb/s to disk if python mode is enabled.
If I disable Python mode or disable pfBlockerNG in general, UNBOUND no longer does it’s sustained disk writing.So what could cause that behavior?
-
@keyser said in Average writes to Disk:
Just as a follow up I think I have now tried EVERY possible setting in my pfBlockerNG setup
Good Morning (here it is),
I do not think pfblockerNG (in my case) is the culprit - I just set up a APU2 machine that was yesterday with ZFS and now with UFS and ... voilà: the writings are GONE!
iostat -d 5 6
md0 ada0 pass0
KB/t tps MB/s KB/t tps MB/s KB/t tps MB/s
0.00 0 0.00 22.55 13 0.30 0.38 0 0.00
0.00 0 0.00 0.00 0 0.00 0.00 0 0.00
0.00 0 0.00 0.00 0 0.00 0.00 0 0.00
0.00 0 0.00 4.00 0 0.00 0.00 0 0.00
0.00 0 0.00 4.00 0 0.00 0.00 0 0.00
0.00 0 0.00 0.00 0 0.00 0.00 0 0.00This seams to prove my suspicion from yesterday that ZFS is causing the heavy writings to disk even if no service is activated on the firewall.
PS. Here the same machine with the same config but ZFS:
iostat -d 5 6
md0 ada0 pass0
KB/t tps MB/s KB/t tps MB/s KB/t tps MB/s
0.00 1 0.00 16.67 41 0.67 0.38 0 0.00
0.00 0 0.00 11.29 26 0.28 0.00 0 0.00
0.00 0 0.00 14.13 19 0.26 0.00 0 0.00
0.00 0 0.00 12.38 21 0.25 0.00 0 0.00
0.00 0 0.00 14.70 19 0.27 0.00 0 0.00
0.00 0 0.00 14.06 21 0.29 0.00 0 0.00Have a good trip to weekend ...
fireodo -
I hope I remember correctly, but zfs by default writes every 5 seconds if there is anything to write. Also it depends on type of write operation (synchronous or asynchronous). Because it is easy to revert copy of the pfsense configuration I changed a little zfs configuration on my device (but with it there is a little bit bigger chance of problems in case of not clean shutdown)
So for my device I changed the following:
- make all writes asynchronous (probably won't help much here, but software doesn't have to wait for OS to finish writing)
zfs set sync=disabled zroot- System -> Advanced -> System Tunables - set vfs.zfs.txg.timeout to 180 - it will increase time between writes from 5s to 180s; during this time all operations will happen in RAM; but writes could happen earlier if there is too much to write (also OS is able to force writing earlier - I'm not expert so I don't know all conditions); for me write happens once or twice during said 3 minutes
- because there is bigger chance of failure with 180s I made zfs to write everything twice (I have 100GB SSD so it is not problem); this won't guaranty data safety, but still (works only for newly written data - old won't be touched)
zfs set copies=2 zrootThat works for me. Please read about it before changing anything. Or at least have configuration backup before you try.
-
I use ZFS also but with RAM disks. this will reduce the writes to the ssd massively, right?
KB/t tps MB/s KB/t tps MB/s KB/t tps MB/s KB/t tps MB/s 0.00 1 0.00 0.00 1 0.00 13.97 1 0.01 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 12 0.00 7.86 23 0.18 0.00 0 0.00 0.00 2 0.00 0.00 2 0.00 0.00 0 0.00 0.00 0 0.00 0.00 3 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 -
I followed your suggestions and it looks good:
iostat -d 5 6 md0 ada0 pass0 KB/t tps MB/s KB/t tps MB/s KB/t tps MB/s 0.00 0 0.00 15.55 14 0.21 0.38 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00This is the production machine where initially I found that heavy writing. I give it 24 hours and keep an eye also on the LBA_written.
Thanks anyway!
fireodo -
@tomashk said in Average writes to Disk:
zfs set sync=disabled zroot
Is this command permanent or has it to be made on each reboot? Thanks
-
This is the SMART Test output from one of my boxes, APU2 Board with 16GB SSD...
241 Lifetime_Writes_GiB shows GB count written.... -> 4176.278 TB???? no way....SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 8694 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 42 168 SATA_Phy_Error_Count 0x0012 100 100 000 Old_age Always - 0 170 Bad_Blk_Ct_Erl/Lat 0x0013 100 100 010 Pre-fail Always - 0/20 173 MaxAvgErase_Ct 0x0000 100 100 000 Old_age Offline - 385 (Average 775) 192 Unsafe_Shutdown_Count 0x0012 100 100 000 Old_age Always - 4 194 Temperature_Celsius 0x0023 070 070 000 Pre-fail Always - 30 196 Not_In_Use 0x0000 100 100 000 Old_age Offline - 0 218 CRC_Error_Count 0x0000 100 100 000 Old_age Offline - 0 241 Lifetime_Writes_GiB 0x0012 100 100 000 Old_age Always - 4176278 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended captive Completed without error 00% 8694 - # 2 Short captive Completed without error 00% 8694 - # 3 Short offline Completed without error 00% 2557 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. -
@tohil said in Average writes to Disk:
241 Lifetime_Writes_GiB shows GB count written.... -> 4176.278 TB???? no way....
Smart is always Device specific - you have to dig for the correct interpretation of those values ... 4 PB is heavy and I don't believe it even its theoretically possible ...
-
@fireodo said in Average writes to Disk:
@tomashk said in Average writes to Disk:
zfs set sync=disabled zroot
Is this command permanent or has it to be made on each reboot? Thanks
It is permanent. You can check if it is set with this command:
zfs get -r sync zroot(it will show information for whole zfs file system)
and you can revert it with this command if I remember correctly:
zfs set sync=enabled zroot -
Thank you! Those settings do the trick! Maybe @jimp can take a look on this thread and maybe its something for the next version ...?
Regards,
fireodoKettop Mi4300YL CPU: i5-4300Y @ 1.60GHz RAM: 8GB Ethernet Ports: 4
SSD: SanDisk pSSD-S2 16GB (ZFS) WiFi: WLE200NX
pfsense 2.7.2 CE
Packages: Apcupsd Cron Iftop Iperf LCDproc Nmap pfBlockerNG RRD_Summary Shellcmd Snort Speedtest System_Patches. -
Yeah I would hope that the default settings used for zfs install wouldn't be a determinant to life of SSD or eMMC would have issues with total writes as well..
I don't know of a way to check what eMMC reports for total life write, etc.
-
@johnpoz said in Average writes to Disk:
I don't know of a way to check what eMMC reports for total life write, etc.
As I don't have any device here with eMMC (OK, except my Phone but that's out of my research-reach :-D ) I cannot say anything about it. Is it smart capable? Documentation says its a kind of predecesor of SD-Card ...
-
If for whatever reason the onboard eMMC died, I know you can add a msata to it.. So that would always be an option.
But would be curious if there is a way to get info from it on total data written, etc.
