realtek-re-kmod missing in pfSense 2.6 repository?

MxcZXAKM

@w0w thanks, his solution seemed to just be setting a static ARP/MAC for his connected rotating server. I have a direct pipe to the WAN on mine, simple home setup.

stephenw10

Usually seeing that message indicates pfSense no longer has an interface with an IP address in the same subnet as the indicate IP so it cannot ARP for it. So usually it's the gateway address on a dynamic connection and the interface has lost it's lease or similar.
Adding a static ARP entry there prevents it trying so you don't see that error but doesn't actually allow it to function in that circumstance. Usually those errors are only while a WAN reconnects.

Steve

MxcZXAKM

@stephenw10 maybe setting the default gateway to WAN instead of automatic would help but in my case I can’t because of the VPN connection.

stephenw10

Hmm, usually that's exactly when you should have it set to WAN and not auto.

This should be in a new topic though.

bepa888

It has been seven days since I upgraded to realtek-re-kmod driver version 197.00, and my pfSense 2.6 box's LAN and WAN interfaces have not flapped even once. In the previous version, 196.04, the interfaces flapped randomly every one to four days and needed a reboot to fix the issue. Due to the frequent flapping issue with v196.04, I created a cron job that is scheduled to run every minute to check if an interface is flapping. The cron job will automatically reboot the OS if an interface has flapped more than five times (down/up/down/up/down). The OS reboot took ~40 seconds.

My box is a Gigabyte EL-20-3710-32G, and my internet bandwidth is 300 Mbps for upload and download. PowerD, Crypto Hardware, Kernel PTI, MDS Mode, RAM disks, hardware checksum offload, TCP segmentation offload, and hardware large receive offload are all disabled. I haven't changed anything other than upgrading the Realtek driver to version 197.00. Hopefully, the Realtek NIC flapping issue has been permanently fixed.

Below are the settings in my /boot/loader.conf.local and /boot/loader.conf:

if_re_load="YES"
if_re_name="/boot/modules/if_re.ko"
hw.re.msi_disable=1
hw.re.msix_disable=1
hw.re.eee_enable=0
hw.re.phy_power_saving=0
hw.re.phy_mdix_mode=0
hw.re.max_rx_mbuf_sz="2048"
legal.intel_wpi.license_ack=1
legal.intel_ipw.license_ack=1
legal.intel_iwi.license_ack=1

goovich

@bepa888 any updates?

bepa888

@goovich Ever since I installed the realtek-re-kmod driver version 197.00 25 days ago, there has been no flapping on either the LAN or WAN Realtek ports. Yay!

goovich

@bepa888 thank you for the update! Hope my Zbox CI323 nano will stop locking/hanging.

HaskyCrawford

@xenium1024 i'm same erro in 196 197 and 198 repo!

stephenw10

In 2.6? Do this: https://forum.netgate.com/post/1100295

HaskyCrawford

@stephenw10 Hello Good morning from Brazil!
Thanks, but after this configuration my pfsense broken :\

image url)

I access to pfsense and its see you crash report, but i don't now how add here my log .tar

HaskyCrawford

@stephenw10 i post in gist.github

https://gist.github.com/haskycrawford/f69722c7cdb9a02c2c87e1798d665307

stephenw10

Hmm, not a crash I'm familiar with. It did load the driver correctly though.

Is that part of an HA pair? The crash is in pfSync:

db:0:kdb.enter.default>  bt
Tracing pid 12 tid 100115 td 0xfffff800058a0740
kdb_enter() at kdb_enter+0x37/frame 0xfffffe008702c5f0
vpanic() at vpanic+0x197/frame 0xfffffe008702c640
panic() at panic+0x43/frame 0xfffffe008702c6a0
trap_fatal() at trap_fatal+0x391/frame 0xfffffe008702c700
trap_pfault() at trap_pfault+0x4f/frame 0xfffffe008702c750
trap() at trap+0x286/frame 0xfffffe008702c860
calltrap() at calltrap+0x8/frame 0xfffffe008702c860
--- trap 0xc, rip = 0xffffffff8109a0c6, rsp = 0xfffffe008702c930, rbp = 0xfffffe008702c950 ---
pfsync_state_export() at pfsync_state_export+0x26/frame 0xfffffe008702c950
pfsync_sendout() at pfsync_sendout+0x280/frame 0xfffffe008702ca00
pfsyncintr() at pfsyncintr+0xd1/frame 0xfffffe008702ca50
ithread_loop() at ithread_loop+0x23c/frame 0xfffffe008702cab0
fork_exit() at fork_exit+0x7e/frame 0xfffffe008702caf0
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe008702caf0
--- trap 0, rip = 0, rsp = 0, rbp = 0 ---

Dobby_

@haskycrawford

Here it begins....

<118>Setting up gateway monitors...


Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address	= 0x0
fault code		= supervisor read data, page not present
instruction pointer	= 0x20:0xffffffff8109a0c6
stack pointer	        = 0x28:0xfffffe008702c930
frame pointer	        = 0x28:0xfffffe008702c950
code segment		= base 0x0, limit 0xfffff, type 0x1b
			= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags	= interrupt enabled, resume, IOPL = 0
current process		= 12 (swi1: pfsync)
trap number		= 12
panic: page fault
cpuid = 0
time = 1682586946
KDB: enter: panic

And that may be the point were it struggles about.

fault virtual address	= 0x0
fault code		= supervisor read data, page not present

HaskyCrawford

@stephenw10 i don't have a HA pfsense, i have 3 network cards 2 WAN and 1 LAN all Realtek 8111.

stephenw10

Hmm, OK. Since you have a screenshot does that mean it did boot correctly after that? Or did you roll back the driver to get that?