[solved] pfSense (2.6.0 & 22.01 ) is very slow on Hyper-V

stephenw10

Do you see the same thing using iperf3 -c 192.168.189.10 -R as you do if you run the client on 192.168.189.10?

That opens the states the other way so it would be interesting to see if it fails in the opposite direction.

Steve

Bob.Dig

Dammit, if I only knew about the -R thing earlier.

m0nji

@stephenw10
Sure that you want to have a iperf test when the test does not even leave the vm? But no problem:

Here also the tests again from both VMs with the pfSense in between

And also a test between both VMs without pfSense (on the same subnet)

m0nji

If it helps, i also did a test from the Windows VM to the pfSense 2.6.0 VM directly

Thats kind of interesting. So that means the problem just exist when pfSense is in between, doing routing, but it does not exist when the pfSense is a direct target/source. This would also explain, why i don't see this weird results when i do the test with the FreeBSD VM (1st post, second screenshot)

m0nji

Ok did some further testing and i think i can confirm that the problem is FreeBSD 12.3 related, not pfSense specific.

I configured 2 FreeBSD VMs, one 12.3 and one 13.0 with Routing enabled (gateway_enable="YES") so that they can simulate the pfSense.

I then did iperf tests:

Win VM (192.168.189.10) --> FreeBSD 12.3 VM (192.168.187.250 / 192.168.189.250) --> Win VM (192.168.187.11)

PS C:\Users\m0nji\Downloads\iperf-3.1.3-win64\iperf-3.1.3-win64> .\iperf3.exe -c 192.168.187.11
Connecting to host 192.168.187.11, port 5201
[  4] local 192.168.189.10 port 58723 connected to 192.168.187.11 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   254 MBytes  2.13 Gbits/sec
[  4]   1.00-2.00   sec   268 MBytes  2.25 Gbits/sec
[  4]   2.00-3.00   sec   282 MBytes  2.37 Gbits/sec
[  4]   3.00-4.00   sec   302 MBytes  2.53 Gbits/sec
[  4]   4.00-5.00   sec   304 MBytes  2.55 Gbits/sec
[  4]   5.00-6.00   sec   304 MBytes  2.55 Gbits/sec
[  4]   6.00-7.00   sec   297 MBytes  2.49 Gbits/sec
[  4]   7.00-8.00   sec   302 MBytes  2.54 Gbits/sec
[  4]   8.00-9.00   sec   294 MBytes  2.47 Gbits/sec
[  4]   9.00-10.00  sec   301 MBytes  2.52 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.00  sec  2.84 GBytes  2.44 Gbits/sec                  sender
[  4]   0.00-10.00  sec  2.84 GBytes  2.44 Gbits/sec                  receiver

iperf Done.
PS C:\Users\m0nji\Downloads\iperf-3.1.3-win64\iperf-3.1.3-win64> .\iperf3.exe -c 192.168.187.11 -R
Connecting to host 192.168.187.11, port 5201
Reverse mode, remote host 192.168.187.11 is sending
[  4] local 192.168.189.10 port 58726 connected to 192.168.187.11 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.01   sec  55.6 KBytes   449 Kbits/sec
[  4]   1.01-2.01   sec  21.4 KBytes   175 Kbits/sec
[  4]   2.01-3.00   sec  21.4 KBytes   178 Kbits/sec
[  4]   3.00-4.01   sec  21.4 KBytes   173 Kbits/sec
[  4]   4.01-5.01   sec  17.1 KBytes   140 Kbits/sec
[  4]   5.01-6.01   sec  21.4 KBytes   175 Kbits/sec
[  4]   6.01-7.01   sec  21.4 KBytes   175 Kbits/sec
[  4]   7.01-8.01   sec  21.4 KBytes   176 Kbits/sec
[  4]   8.01-9.01   sec  15.7 KBytes   128 Kbits/sec
[  4]   9.01-10.01  sec  20.0 KBytes   163 Kbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.01  sec   384 KBytes   314 Kbits/sec                  sender
[  4]   0.00-10.01  sec   237 KBytes   194 Kbits/sec                  receiver

iperf Done.

Win VM (192.168.189.10) --> FreeBSD 13.0 VM (192.168.187.251 / 192.168.189.251) --> Win VM (192.168.187.11)

PS C:\Users\m0nji\Downloads\iperf-3.1.3-win64\iperf-3.1.3-win64> .\iperf3.exe -c 192.168.187.11
Connecting to host 192.168.187.11, port 5201
[  4] local 192.168.189.10 port 49997 connected to 192.168.187.11 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   268 MBytes  2.25 Gbits/sec
[  4]   1.00-2.00   sec   300 MBytes  2.51 Gbits/sec
[  4]   2.00-3.00   sec   316 MBytes  2.65 Gbits/sec
[  4]   3.00-4.00   sec   316 MBytes  2.65 Gbits/sec
[  4]   4.00-5.00   sec   318 MBytes  2.67 Gbits/sec
[  4]   5.00-6.00   sec   316 MBytes  2.65 Gbits/sec
[  4]   6.00-7.00   sec   317 MBytes  2.66 Gbits/sec
[  4]   7.00-8.00   sec   319 MBytes  2.68 Gbits/sec
[  4]   8.00-9.00   sec   319 MBytes  2.67 Gbits/sec
[  4]   9.00-10.00  sec   316 MBytes  2.65 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.00  sec  3.03 GBytes  2.60 Gbits/sec                  sender
[  4]   0.00-10.00  sec  3.03 GBytes  2.60 Gbits/sec                  receiver

iperf Done.
PS C:\Users\m0nji\Downloads\iperf-3.1.3-win64\iperf-3.1.3-win64> .\iperf3.exe -c 192.168.187.11 -R
Connecting to host 192.168.187.11, port 5201
Reverse mode, remote host 192.168.187.11 is sending
[  4] local 192.168.189.10 port 49999 connected to 192.168.187.11 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   326 MBytes  2.73 Gbits/sec
[  4]   1.00-2.00   sec   324 MBytes  2.72 Gbits/sec
[  4]   2.00-3.00   sec   337 MBytes  2.83 Gbits/sec
[  4]   3.00-4.00   sec   340 MBytes  2.85 Gbits/sec
[  4]   4.00-5.00   sec   337 MBytes  2.83 Gbits/sec
[  4]   5.00-6.00   sec   340 MBytes  2.85 Gbits/sec
[  4]   6.00-7.00   sec   341 MBytes  2.86 Gbits/sec
[  4]   7.00-8.00   sec   342 MBytes  2.87 Gbits/sec
[  4]   8.00-9.00   sec   342 MBytes  2.87 Gbits/sec
[  4]   9.00-10.00  sec   342 MBytes  2.87 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.00  sec  3.29 GBytes  2.83 Gbits/sec                  sender
[  4]   0.00-10.00  sec  3.29 GBytes  2.83 Gbits/sec                  receiver

iperf Done.

stephenw10

Ah, nice. Ok, I wonder what changed in 12.3 then. Hmm.

@m0nji said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

Sure that you want to have a iperf test when the test does not even leave the vm?

No sorry I meant swap the server and client iperf machines to see if opening the states the other way changes the direction that is slow. It seems very likely it will though.

Steve

Bob.Dig

Let's hope netgate will ditch 12.3 sooner than later...

provels

Maybe it's been mentioned already, but I have read at altaro.com that the VMQ feature can be problematic. I have it disabled and have no issues, but I'm also running an i340-T4 on 2012R2. Maybe MS has fixed it. YMMV

Article at Altaro, skip to Culprit #2

cannyit

@rmh-0 Thanks, also sovled it in my environment. Happy to be back on normal performace.

Bob.Dig

Because none of this helped in my case, I tried dda a quad-port-intel 1G-NIC into pfSense. This worked, so I was able to use no virtual NICs at all in pfSense. My test Windows-VM is still using a virtual adapter but now has to go through a physical switch every time... with that, everything is working like it should. Now I hope I can dda my 10G-NIC in pfSense too.

rgijsen

Just for some additional info:
We run pfSense in HA (carp) on 2 Hyper-V gen2 VM's. Both run on Hyper-V 2022. Both on HPe DL360 Gen10 hardware, both with 2 HPE FlexFabric 10Gb 2-port 556FLR-SFP nics, that are teamed in a VSwitch SET with dynamic loadbalancing on the nics (Switch Embedded Teaming, no LACP). We always disable RSC during the install scripts, as it gave us nothing but troubles. VMQ is not enabled for the pfSense VM's either, as in the past it didn't work with VMQ anyway. For the love of God I cannot replicate this issue of slow intervlan traffic.

However, a colleage-company we work with have this issue on their internal network. Now, that is a gen1 VM on a DL360 gen9, with a SET team on the 4 regular internal HPe 331i nics, but with Hyper-V port balancing. They have two Hyper-V nodes (clustered) and their pfSense 2.6.0 VM is on one of those nodes. They have a hardware NAS accessible through SMB. Now, accessing that NAS (different VLAN) is slow as molasses, BUT ONLY when the VM accessing the NAS is on the same host as the pfSense VM. When we move the VM, or pfSense to the other node, poof everything is up to linespeed again. We move the two VM's back together and it's turdspeed again.

When we access a SMB share from physical machines in another VLAN, when we run the VM with the SMB share on the same Hyper-V host as pfSense 2.6, access to that share is super slow. When we move that VM to another host, it all works fine. So for this specific environment it seems like the inter-vlan routing performance is only bad if those VMs reside on the same host as pfSense.

Needless to say it all works fine with 2.5.x.

The one thing I see in common with at least one person in this thread is that the problem pfSense runs on HPe Gen9 hardware. Are there more people running on Gen9 with issues? If you guys use a SET team, what is the load balancing mode?

m0nji

@cannyit you fixed your slow WAN speed but not the inner vlan routing?!
I think it needs two separate threads because we are talking about 2 different problems

m0nji

@rgijsen no i was using a lab system (Ryzen based Windows 11 Pro with Hyper-V enabled and 10Gig Asus Nic)

rgijsen

This post is deleted!

cannyit

@m0nji WAN speed or better speed between all interfaces is fine again after disable RSC. I didnt had an issue with inter VLAN routing. I have vlans tagged within pfsense but speed is OK.

stephenw10

Is the VLAN issue only happening on gen 1 VMs?
That was an early theory but I've not seen definite conclusion.

Bob.Dig

@stephenw10 said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

Is the VLAN issue only happening on gen 1 VMs?
That was an early theory but I've not seen definite conclusion.

It is not VLAN related but related to hn interfaces and or virtual switches I would say.
Just for the record:

First who encountered it
Server 2022 Gen2 VM
AMD System
WAN-Speed never was affected
Even just using virtual adapters on private switch without VLAN it happened
Most probably a bug in FreeBSD 12.3 regarding hyper-v

stephenw10

Mmm, I'd bet it's going to be one of these changes from Mar 2021:
https://github.com/pfsense/FreeBSD-src/commits/RELENG_2_6_0/sys/dev/hyperv/netvsc

And given that one of those enabled RSC support....

hendryjl

+1 for Disabling RSC. My setup...

Home "power user"
Fitlet2 with three network interfaces
Windows Server 2019
Hyper-V Gen 1 VM.
** Three virtual switches (one for each ISP, one for switch)
** 7 network interfaces at VM level (one for each ISP, 5 for 5 VLANs, set with VLAN tagging at virtual NIC level in HyperV)
** All virtual nics with every check box disabled except VLAN (no VMQ, etc)

WAN speed was terrible. Changed software receive side coalescing on the VM switches, and all good.

Commands used:

Check:
Get-VMSwitch | % { $_ | Select-Object *RSC* }

Change:
Get-VMSwitch | % { $_ | Set-VMSwitch -EnableSoftwareRsc $false }

Re-Check:
Get-VMSwitch | % { $_ | Select-Object *RSC* }

Bob.Dig

Yup, that is the main difference, it is not about WAN-Speed in my and some few others cases.
If WAN then RSC.

I had disabled RSC today a second time, even rebooted the host, it again didn't helped in my case.