VLAN on D-link

fireix

@rcoleman-netgate Indeed. Also marked the checkbox to enabled the interface and put firewall-rule in place.

One thing.. I haven't actually defined any VLAN1 on pfSense, as the main mode is non-vlan setup and I don't want to disrupt non-tagged traffic. Could that be the issue? I don't think it should, as I should anyway be able to ping the interfaces IP-address in VLAN40.

rcoleman-netgate

@fireix Doubtful. VLAN1 = unnumbered, likely your LAN.

Is this a whitebox or one of our devices? What do you see when you run a PCAP on the interface?

fireix

@rcoleman-netgate said in VLAN on D-link:

PCAP

It is a Supermicro-server with pfSense installed and 4 ports. Haven't really ran an PCAP on it. Do you mean on the entire LAN, is it easy to identify VLAN-id tags in it? I'm only really basic on wireshark-skills, no idea how those packages will look like. I have a ton of non-vlan traffic, so will be a lot of noise.

rcoleman-netgate

@fireix You can run the PCAP on just the VLAN interface in question.

https://docs.netgate.com/pfsense/en/latest/diagnostics/packetcapture/index.html

bingo600

@fireix said in VLAN on D-link:

I'd do as @rcoleman-netgate says
Try to capture some packets on pfSense , while pinging the pfSense IF.
Both the way where it failed , and the way where you had succeed (Vlan1 ??)

Tip: Capture detailed/all , save the file. Then it can be opened in Wireshark.

RE:

But only communication between ports on VLAN40, I can't communicate with Port 1. In my head, it should have been tagged port, but this interface almost looks the oposite of what I find logic... But you are two people saying it looks normal, so I will go with that for now ;)

You could make P1 (or try w P2) a Tagged port.
The only difference as i see it (30 sec glimpse at the Dlink 15xx config example) , is that you can't run Native/untagged data on it.
So you have to TAG Vlan1 data also on the pfSense, aka Tag Vlan1 & Vlan40.

This would be my preference anyways (tagged only), i'll always avoid those Hybrid ports when not needed.
UniFI AP's springs to mind , as needs Hybrid ... Well at least in older fw.

And i tend to avoid Vlan1 use anywhere in my infrastructure .. Old working habbit.

Btw:
I saw a "View Allowed Vlans Button" on the pict with the Voan40 definition.
Does that give any clue .... Ie. Vlan40 not allowed

Edit:
You could also setup a "Monitoring port" on the switch , and connect a PC w. Wireshark to that one.

Here's how it's done on a D-Link 1210 , couldn't find anything for a 1510
https://eu.dlink.com/uk/en/support/faq/switches/layer-2-gigabit/dgs-series/es_dgs_1210_como_monitorear_trafico_de_un_puerto_port_mirroring

/Bingo

fireix

@bingo600 said in VLAN on D-link:

I saw a "View Allowed Vlans Button" on the pict with the Voan40 definition.

That's the button I click to get to this screen posten above - to verify the setup:
alt text

"You could make P1 (or try w P2) a Tagged port."

That I have tried for days to do - based on everything I have read, that is the way it is done usually :) Port 1 is the main port to pfSense/Internet and is clearly a "tagged" candidate. But when I edit the VLAN40 and select Port 1 Tagged port in the screen below, it doesn't stick when I click Apply. I tried for port 2 now as you suggested and there it actually sticks/works like I want Port 1 to do. Now, if I just managed to do that with Port 1, I think it would work rigth away :)

screenshot-77.40.236.4-2022.06.23-11_41_39.png

I can't see any clear difference on port 1 vs port 2.. they are both Hybrid and both part of VLAN1 (or by default at least). But maybe this gives an important clue... Btw, after I added the Port 2, it automatically did this under Allowed VLAN-page, so config looks similar to Port 1:

Btw: I tried to remove the checkbox for "Native VLAN" on the port 1 (and 2, 3, 4) on the ports inside VLAN1, but it wouldn't stick either. Neither from the port-membership-overview page or the interface for each port. On the port-mebership-overview for VLAN40, I could remove the checkbox for all ports and that is how it is now.

Tagged VLAN40 disappeared from the Allowed VLAN on port 1 when I play around a bit. I have to re-add it manually on the VLAN interface port 1 every timeI do a small edit. I think forcing it doesn't work, it does however sticks on Port 2 as it should no matter what. So that tells me that D-Link doesn't allow it, it will be removed by the system. So even if it looks good on that last picture above, it is probably not respecting the VLAN40-tagged on Port 1.

fireix

@rcoleman-netgate said in VLAN on D-link:

@fireix You can run the PCAP on just the VLAN interface in question.

https://docs.netgate.com/pfsense/en/latest/diagnostics/packetcapture/index.html

Ah, it is built-into the GUI, nice :)

I ran it both in "Enable promiscuous mode" and without. Tried to ping both from the machine I have setup on VLAN40 (with static IP in DHCP-range) and from pfSense. The data below is from pfSense (I pinged machine 192.168.50.15 with no reply)

12:05:26.303035 ARP, Request who-has 192.168.50.15 tell 192.168.50.1, length 28
12:05:27.303720 ARP, Request who-has 192.168.50.15 tell 192.168.50.1, length 28

I think it is is purly a config error in D-Link, port 1 is simply not "connected" on VLAN40 internally.

bingo600

@bingo600 said in VLAN on D-link:

You could make P1 (or try w P2) a Tagged port.
The only difference as i see it (30 sec glimpse at the Dlink 15xx config example) , is that you can't run Native/untagged data on it.T
So you have to TAG Vlan1 data also on the pfSense, aka Tag Vlan1 & Vlan40.

Sorry i meant Trunk port above , where i wrote Tagged.
Try to set P2 as Trunk , allowing VL40

Something is is spookey with that switch or FW ....

Try to capture on interface , not Vlan40 , that way you should be able to see if it is tagging packets with VL40.

I agree with that D-Link port , not tagging VL40 packets.
We miss a "little important thing" ..... I have no idea what ....
But you might be right in , when the "D-Link gui removes the VL40 tagging" , it might be a hint ....

Strange ... It's so easy on a D-Link 1210

I just had another glance at this
https://eu.dlink.com/uk/en/support/faq/switches/layer-2-gigabit/dgs-series/es_dgs_1510_escenario_config_vlan_por_gui_y_cli

Strange ... It seems to use a totally different way to GUI configure the ports.

You did say you had success in adding the VL40 tag to P2 , did you try to connect the pfS to that port ??

/Bingo

fireix

@bingo600

I tried the console on the switch, run the command "show vla" to list all VLANs.

It reports this:


 VLAN 1
   Name : default
   Description :
   Tagged Member Ports   :
   Untagged Member Ports : eth1/0/1-1/0/33,eth1/0/35-1/0/42,eth1/0/44-1/0/50,
                           eth2/0/1-2/0/50,eth3/0/1-3/0/50,eth4/0/1-4/0/50

 VLAN 40
   Name : VLAN0040
   Description :
   Tagged Member Ports   : eth1/0/2
   Untagged Member Ports : eth1/0/34,eth1/0/43

 Total Entries : 2

bingo600

@fireix

That seems like it has accepted VL40 tagged on P2
Try to Connect the pFS IF to port2

Do you have a 4-Unit Stack ??

What port is your Management PC connected to ?
Sometimes the port where the PC is connected behaves weird , if you want to "kill" the Vlan you're actually Managing via,

fireix

@bingo600

Two units stack. The interface is showing 4 even if you have 2,3 or 4..

Indeed, Port 2 works just like I want both in the GUI and in the console.

I wish I could just switch it over :) But then I take down all customers while testing, so want to try to avoid it.

Maybe a way to copy all traffic on Port 1 to Port 2.. port mirror?

bingo600

@fireix
Have to leave ... Wife is home
BB in 3..4 hours

fireix

@bingo600 Hmm....

On my pfSense LAN, I have LACP-lag that goes to Port 1 on Switch 1 and Port 48 on Switch 2. I didn't think this mattered, but this migth be the cause.

I tried to put port 48 on Switch #2 into tagged-mode. Same symptom: The interface shows it is possible for this port to join VLAN40, but once I choose it and Submit, it is removed. When I did the same on the empty port 47 next to it, it sticked and worked like it should. Either I'm not allowed to put tagged on a live-port that is plugged in - or the switch refuse to put a port in LAG into tagged mode.

I see from a FAQ that VLAN-settings should be set to same on both individual ports that are member of the team, but how can I do that when D-link automatically removes the configuration before I can set it on 2nd unit..

Port definition is exactly the same for port 47 and 48 (like 1 and 2), so I can't see any other reason.

Edit: Using the "Clone port" option I was able to transfer the settings on Port 1 SW1 to port 48 SW2. But no such option for VLAN-membership.

fireix

@fireix

I tested tagging port #2 in a VLAN and then let it join in a LACP-bond/channel.. Boom, it removed the tagging setting on port #2.

fireix

I disabled all LAG/team links and connected pfSense to fresh port #3. As you see. port 3 on VLAN60 is tagged as it should.

The computer in port 34 on VLAN60 is Access port.

No contact between pfSense and the computer on VLAN60.

 VLAN 1
   Name : default
   Description :
   Tagged Member Ports   :
   Untagged Member Ports : eth1/0/1-1/0/33,eth1/0/35-1/0/42,eth1/0/44-1/0/50,
                           eth2/0/1-2/0/50,eth3/0/1-3/0/50,eth4/0/1-4/0/50

 VLAN 40
   Name : VLAN0040
   Description :
   Tagged Member Ports   : eth1/0/2,eth1/0/46,eth2/0/47
   Untagged Member Ports : eth1/0/43,eth2/0/46

 VLAN 60
   Name : VLAN0060
   Description :
   Tagged Member Ports   : eth1/0/3
   Untagged Member Ports : eth1/0/34

fireix

I have a computer where I can set the VLAN ID on and I put it to 70 on pfSenses LAN port. I got on to correct VLAN and got DHCP for VLAN70 rigth away. So error is 100% in the switch. No idea what more to try.. No way to get the VLAN tag passed through port 3 to any port no matter what I do.

Port 3 shows tagged VLANs 60,70.

fireix

@fireix

By defining an IP under meny for Layer 3 LAN interfaces on the switch with an IP in the DHCP-range, I suddenly managed to ping my pfSense (and all other networks). I could however ping everything on the pfSense. Is it supposed to work like that? Seems like I can block it under firewall rules.

This I found on the pfSense (it is the switch interface address on VLAN60 that has sent out UDP packets).

Still no DHCP though.. Doesn't get assigned.

fireix

And suddenly I have DHCP also!

Now just have to see that the VLAN seperation actually works, I can ping most stuff, by I assume it all goes through the pfSense and not port-to-port now and then I can at least filter out all traffic I want :)

bingo600

@fireix

Nice that you are making progress.

But watch out on enabling L3 on the switch , if done "incorrectly" you could easily bypass the pfSense fwall , and route packets between vlans directly on the switch.

fireix

@bingo600 Do you see any error in the "show vla" command on the console of the switch above? Not sure why it doesn't work without layer 3. Would be so much easier to avoid it, but I get no outside VLAN60 communication whatever I do.

One problem I discovered after enabling layer 3 and still not seeing DHCP, was that the switch had enabled DHCP-protection on most of the ports. Probably done years ago... So that was important discovery at least.

I see that I can control through firewall-rules on pfSense where VLAN60 can go. If I have a server in VLAN1, I can have a rule that by default block all traffic from VLAN60 to not go to servers inside VLAN1. That is a big positive. Doesn't this indicate that correct setup? Or do you think that if I create a layer3 IP on switch for VLAN40, it will allow traffic between VLAN40 and VLAN60 without going through the firewall?