Netgate 6100 Max - Only showing 13G (ufs) but have 128gb

umitdk

Hi guys,

I have a Netgate 6100 Max and after upgrade to 22.05-RELEASE it shows "13G" disk.

Filesystem Size Used Avail Capacity Mounted on
/dev/ufsid/60b9301175a9965b 13G 1.8G 10G 15% /
devfs 1.0K 1.0K 0B 100% /dev
tmpfs 4.0M 124K 3.9M 3% /var/run
devfs 1.0K 1.0K 0B 100% /var/dhcpd/dev

How can i claim rest of the space?

Also when i goto Diagnostics -> S.M.A.R.T. StatusInformation & Tests
then i cannot select any drive in "Select a drive and type:"

the Netgate 6100 is running orignal harddrive, and nothing physical is changed.

stephenw10

It looks like it's booting from eMMC. You can confirm that at the command line using:
glabel status
And
geom disk list

Are you sure it was installed to SSD before the upgrade?

Steve

umitdk

@stephenw10 Yes it was installed on SSD.

glabel status:

Name Status Components
ufsid/60b9301175a9965b N/A mmcsd0p2
gptid/1027920e-1c2f-11ec-a1f0-90ec771d1e9a N/A mmcsd0p3
gptid/edfff163-c4a3-11eb-98a4-44a8422fabb9 N/A mmcsd0p1
msdosfs/EFISYS N/A mmcsd0p1

geom disk list:

Geom name: mmcsd0
Providers:

Name: mmcsd0
Mediasize: 15678308352 (15G)
Sectorsize: 512
Stripesize: 512
Stripeoffset: 0
Mode: r2w2e5
descr: MMCHC TB2916 9.0 SN 322C4E04 MFG 09/2020 by 112 0x0000
ident: 322C4E04
rotationrate: 0
fwsectors: 0
fwheads: 0

Geom name: mmcsd0boot0
Providers:

Name: mmcsd0boot0
Mediasize: 4194304 (4.0M)
Sectorsize: 512
Stripesize: 512
Stripeoffset: 0
Mode: r0w0e0
descr: MMCHC TB2916 9.0 SN 322C4E04 MFG 09/2020 by 112 0x0000
ident: 322C4E04
rotationrate: 0
fwsectors: 0
fwheads: 0

Geom name: mmcsd0boot1
Providers:

Name: mmcsd0boot1
Mediasize: 4194304 (4.0M)
Sectorsize: 512
Stripesize: 512
Stripeoffset: 0
Mode: r0w0e0
descr: MMCHC TB2916 9.0 SN 322C4E04 MFG 09/2020 by 112 0x0000
ident: 322C4E04
rotationrate: 0
fwsectors: 0
fwheads: 0

Seems like its running on mmcsd0p2, how do i find the SSD drive? shouldnt it show up in geom disk list ?

stephenw10

Yes, it should show there as nvd0. Does it appear in the boot log?

If the SSD failed for some reason you would have needed to reinstall to the eMMC. Or at the very least to copy your config back into it.

Steve

umitdk

@stephenw10 i think the SSD died, becuase before i updated to latest version, then it had a crash and was factory reset. i then updated to latest version. do you know which type of ssd drive i have to order?

stephenw10

Any m.2 NVMe drive should work there, I'm not aware of any restrictions. However that must still be in warranty, you should open a support ticket:
https://www.netgate.com/tac-support-request

Steve

umitdk

This post is deleted!

stephenw10

You can always open a ticket for a hardware issue like this.

rcoleman-netgate

@stephenw10 said in Netgate 6100 Max - Only showing 13G (ufs) but have 128gb:

Any m.2 NVMe drive should work there,

Any M- and B-key NVMe drive*

keyser

@umitdk said in Netgate 6100 Max - Only showing 13G (ufs) but have 128gb:

@stephenw10 i think the SSD died, becuase before i updated to latest version, then it had a crash and was factory reset. i then updated to latest version. do you know which type of ssd drive i have to order?

There is a pretty good chance that the BIOS got it’s bootdrive changed and your install was made on the eMMC instead.
I had quite an interesting reinstall session where a BIOS reset caused the eMMC drive to become the boot device, but I still reinstalled on the SSD - that caused all kinds of problems and a pretty difficult way back to the initial state.

Open a ticket with Netgate - They can help you on this since it’s so new.

stephenw10

@rcoleman-netgate said in Netgate 6100 Max - Only showing 13G (ufs) but have 128gb:

Any M- and B-key NVMe drive*

Doh! That's a very good point. I completely forgot about that!
@umitdk take note if you're considering buying your own. It should be under warranty though.

Steve