23.01 -> 23.05 upgrade failed

Raffi_

@DaddyGo said in 23.01 -> 23.05 upgrade failed:

@Raffi_ said in 23.01 -> 23.05 upgrade failed:

I had the same issue with upgrade error through GUI and then the GUI showing I already have the latest install. I was able to solve this by SSHing into console and using "pfsense-upgrade".

Hi Bro, it was the same here ,
I subscribed to this thread and I see you have been here, hope all is well with you, long time no hear from you...

all is good my friend. Been enjoying the nice west coast weather. Hope all is good with you.

BTW:
SSH solves everything, hahaha

haha we are such nerds because we find that funny.

DaddyGo

@Raffi_ said in 23.01 -> 23.05 upgrade failed:

Been enjoying the nice west coast weather. Hope all is good with you.

That's nice, hmmm the ocean is a little warmer at Lisbon - that's why I'm not complaining...:)

Now everything is OK, I had a little health problem, but it's sorting itself out. I've been away from "here" because of that, but now I'll have time and we'll push SSH hard

BTW:
I'll have time to do a bit better with this great NGFW, the "love" has remained

SteveITS

@Gertjan said in 23.01 -> 23.05 upgrade failed:

when you use pfSense+ 23.01, the pfSense package list will show you only the packages available for that "23.01" version and not the other ones.

Actually, that is not correct. It will show packages for the selected branch, which may not be the installed version if this router has not yet upgraded to the latest version, but has Current selected.

In the past one could install/upgrade a package in that state, and the package would pull in software, maybe a later PHP version, and break everything. However I think I did see they are showing a warning now about the version/repo mismatch? I would still select Previous Stable Version if necessary to make them match. There is a redmine about this.

Innz

Is this common for pfsense? I have a 6100 and 4100. Went to update both and now both of them will not load the gui? I have only had them long enough to update the software twice (this being the second time). Worse firewall I have ever used in my life when try to update.

DaddyGo

@Innz said in 23.01 -> 23.05 upgrade failed:

Worse firewall I have ever used in my life when try to update.

Hmmmm

@Innz "Is this common for pfsense?"

No it's not general, don't assume anything at first.
Always make a backup and you can restore it in no time if you're experienced.

SteveITS

@Innz You didn't provide many details. Error message? What does the console show? Logs? You might start a new thread.

If you didn't wait long enough (see my sig) more than one person has rebooted halfway through the update.

driise

@driise
more digging:

this file /usr/local/etc/pfSense/pkg/repos/pfSense-repo-stable.conf points to a hostname that doesn't exist. is this a bug?

lrwxr-xr-x  1 root  wheel  57 May 26 01:20 pfSense.conf -> /usr/local/etc/pfSense/pkg/repos/pfSense-repo-stable.conf

[23.01-RELEASE][admin@NONO]/usr/local/etc/pkg/repos: more pfSense.conf
FreeBSD: { enabled: no }

pfSense-core: {
    url: "pkg+https://pfsense-plus-pkg.netgate.com/pfSense_plus-v23_05_amd64-core",
    mirror_type: "srv",
    signature_type: "fingerprints",
    fingerprints: "/usr/local/share/pfSense/keys/pkg",
    enabled: yes
}

pfSense: {
    url: "pkg+https://pfsense-plus-pkg.netgate.com/pfSense_plus-v23_05_amd64-pfSense_plus_v23_05",
    mirror_type: "srv",
    signature_type: "fingerprints",
    fingerprints: "/usr/local/share/pfSense/keys/pkg",
    enabled: yes
}

[23.01-RELEASE][admin@NONO]/usr/local/etc/pkg/repos: ping firmware.netgate.com
PING firmware.netgate.com (208.123.73.209): 56 data bytes
64 bytes from 208.123.73.209: icmp_seq=0 ttl=43 time=12.406 ms
64 bytes from 208.123.73.209: icmp_seq=1 ttl=43 time=12.473 ms
^C
--- firmware.netgate.com ping statistics ---
2 packets transmitted, 2 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 12.406/12.440/12.473/0.034 ms
[23.01-RELEASE][admin@NONO]/usr/local/etc/pkg/repos: ping pfsense-plus-pkg.netgate.com
ping: Unknown host

jimp

@driise said in 23.01 -> 23.05 upgrade failed:

@driise
more digging:

this file /usr/local/etc/pfSense/pkg/repos/pfSense-repo-stable.conf points to a hostname that doesn't exist. is this a bug?

No.

https://docs.netgate.com/pfsense/en/latest/troubleshooting/upgrades.html#packages-netgate-com-has-no-a-aaaa-record

Different variation on the hostname but same concept.

tman222

@driise - running into similar issues as you've described not being able to update packages:

https://forum.netgate.com/topic/180382/unable-to-upgrade-packages

Any ideas/thoughts on how to further troubleshoot this?

driise

@tman222 At this time, I'm stuck I guess, tried again this morning to get it to update, same issues. Hopefully Netgate will determine the issue and fix.

driise

@jimp

Any feedback on what we're seeing?
Any logs I can provide that might help? I can reproduce the issue easy if there's debug logs or something I can pull.

I reverted my VM instance back to the 23.01 boot image so that my physical and VM (secondary) could properly sync.

aaronssh

@pdavis said in 23.01 -> 23.05 upgrade failed:

After toggling the "Current Stable Version" and "Previous Stable Version" in System/Update/System Update, the GUI now showed 23.05 upgrade option.

So I had the same problem. First attempt at update failed with certificate issues, then my device got "stuck" thinking that 23.01 was the latest. Your steps quoted here fixed it for me too. Very strange!!

Dobby_

@demux said in 23.01 -> 23.05 upgrade failed:

Why? What can happen?

If you upgrade it can be in some cases that
the cert. lease will be gone, and so you only
have to wait a while until it is renewed and then
the entire upgrade process will work again for you without any problems.

Gertjan

@SteveITS said in 23.01 -> 23.05 upgrade failed:

Actually, that is not correct. It will show packages for the selected branch, which may not be the installed version ....

Exact.

That's why I was talking about Netgate being a fortune 500 company : the pfSense package list should correspond the system you are using, which isn't necessarily the list with packages available.
The latest versions of a package become available when you use the latest pfSense version.
Something like that.

This implies that there should be a unique repository for every supported pfSense version. This means a lot of labor to main all this.

pete

Backed up my PFSense 23.01 version fine. Updated and it failed. Rebooted box and it wouldn't boot in to PFSense.

Installed new PFSense CE on the box. Got a new token for PFSense + and see this

Thank you for choosing Netgate pfSense. Your device does not require registration, we recognize it already. You may have already registered, or it may be a pre-registered Netgate appliance.

when I try registration

I should have read the forum before upgrading.

I am using PFSense now with CE release 2.6.0-RELEASE (amd64) and restored backup from PFSense 23.01. (which is wrong and seeing this on boot up)

So this morning installing PFSense CE on backup router and hopefully updating it with PFSense + and then restoring configuration.

Never had an issue like this.

SteveITS

@pete I don’t have a solution but I’ve seen other posts like that. I believe that means Netgate recognizes the calculated NDI and therefore you don’t need a new token. Maybe you can find a thread with the solution…

pete

@SteveITS

Thank you @SteveITS.

Plugged Backup PFSense CE to currently working LAN (on kitchen table - very low on the WAF).

Updated it to PFSense +. It is updating now to 23.01 and leaving it there and restoring backup from other machine.

On reboot it gets all sorts of PHP errors and stays at the login prompt. Rebooted a couple of times and it is the same on reboot. I am screwed right now.

It seemed to stall at the squid prompts. Removed squid package and it booted. Reset the box via command prompt. Restored old build. On reboot dbended on kernel load.

Will start again from scratch on back up box.

Once I get this one going then taking primary off line and redoing it hopefully to work fine.

I am retired and this is a hobby and while I have backup boxes here many folks do not.

Need to step away now and readdress issues this afternoon.

Dobby_

@pete

You could try out installing 2.6 (zfs) and then upgrading to 23.01 and once more to 23.05
and if you will be install also back the config
then it would be the best option in my eyes.
You will need perhaps 30 minutes and all is
fine again. For the spare box I would try out
the 2.7 Development, if it is only a spare box
and for home usage and on top a hobby you
will be fine with it.

pete

Thank-you @dobby.

I did that and it worked and I did not update but when I restored my PFSense + old configuration it debended.

The second time I did it it said it was registered and wouldn't update to PFSense +.

So now booting in Ubuntu and reformatting drive and trying installation again.

This is on a Qotom. I also have two Jetways which I like much better than Qotom which I may try on.

In my retirement now hoarding firewalls ;).

I am still running on the redone Qotom PFSense + box to PFSense CE with the PFSense + backup restored to it. My VPN servers are running fine.

Just that I am occupying the kitchen table with a monitor and another server which is very low on the WAF.

mark_lab_user

@Dobby_ I just finished that exact procedure. All the way back to fresh 2.6 and then the 2 steps to upgrade.

I had to do it because "Available packages" was showing as empty and I was getting an error is syslog relating to the package manager.

And then I also had to update the RTL Ethernet driver to get my 2.5 Gbit card working.

But...

php-fpm[396]: /pkg_mgr_installed.php: The command '/usr/local/sbin/pfSense-repo-setup' returned exit code '1', the output was 'pfSense-repoc-static: invalid signature failed to read the repo data. failed to update the repository settings!!!'

Has returned as of a few minutes ago.

Hmmm.